To better delimit renesas ranges dts, we need to use ranges folder.
It will also help maintainers to better delimit their files to
be notified about.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Add myself as codeowner of the previously committed PWM
driver for the MAX31790.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Add myself as codeowner of the previously committed GPIO
expander driver for the PCAL64XXA.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Add myself as codeowner of the previously committed GPIO
expander driver for the BD8L600FS.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Add myself as codeowner of the previously committed ADC
driver for the ADS114S0X.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Add myself as codeowner of the previously committed SoC
STM32H735 and its disco board.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
I'm using a new account now.
Do the corresponding CODEOWNERS change just for consistency as well.
Signed-off-by: Martí Bolívar <mbolivar@amperecomputing.com>
This driver is built on top of the IVSHMEM doorbell
notification mechanism providing an unified way
to generate inter VM interrupts.
Signed-off-by: Felipe Neves <felipe.neves@linaro.org>
Removes duplicate code and inconsistencies in the naming of the
cc13xx_cc26xx devicetree and RTC driver hierarchy and alignes it with
the actual TI product series naming hierarchy.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The mcumgr subsystem as a whole is already maintained by @nordicjm
(#57780) and I am no longer actively using mcumgr, so removing myself
from the equation and letting more capable hands take over.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
This driver implement basic functions of ili9342c controller
which comes mostly with IPS displays.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
With significant contribution to MCUmgr that brought increased
upload speeds and various other improvements in RAM and CPU usage,
general improvements in MCUmgr architecture and documentation,
Jamie has shown his vision for the subsystem and therefore
lets welcome him as a new MCUmgr subsystem maintainer.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Bsim won't be limited anymore to BT tests.
In preparation for adding more tests in network areas
swap the tests/bluetooth/bsim with tests/bsim/bluetooth
There is no other changes in this commit beyond that.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
- Add Ian Fyall (@ifyall) as codeowner for Infineon/Cypress sources.
- Add Nazar Palamar (@npal-cy) as codeowner for Infineon/Cypress sources.
- Remove Gerson Fernando Budke (@nandojve) from codeowner
of Cypress sources.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
