In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Differently from ESP32, the ESP32-S2 SoC has native
hal support to reset its own I2C FSM in case of failure.
This commit removes warnings related to unused reset
logic, which does not really apply to ESP32-S2.
It also removes code and data structures related to pin
information from the build when the target SoC supports
hardware mechanisms to reset the I2C FSM.
Finally, it checks at compile time if the preconditions
for correct bus recovery are being met.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
though using pinctrl's subsystem, the I2C driver
keeps pin information in case of communication
failure. This information is needed in case of
FSM failure.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
STOP command was issued in the same transmission message
and as from esp-idf, this should be moved into a new
transmission.
Although it works in most scenarios, SHT3X sensor is one
case that presents reading error.
Closes#41385
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
irq_line and irq_enabled call is not necessary as the interrupt
allocater enables it during its initialization.
it also adds end packet to all write transmission instead
of only at the end (burst data scenario)
Add check in gpio configuration check to avoid wrong gpio pins
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Adds the ability for I2C drivers to report synchronous transfer stats
using a I2C specific macro to define the device instance.
The macro creates a container for device_state which allows for per
instance device class common data structure to be used in the device
class api (ex: i2c.h). This is used to maintain per driver instance
stats for all i2c drivers. This is a reusable idea across other device
classes as desired.
Using Kconfig device class stats may be turned on/off individually
this way as well, in this case I2C_STATS.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
- added messages check and fix before transfer
- fixed START and STOP signal generation conditions
- fixed semaphore release for empty messages
Signed-off-by: Konrad Sikorski <znfgnu@gmail.com>
Use i2c_hal functions to enable support for
multiple SoCs.
Use DT compat to enable I2C from device
tree configuration
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Replaces the prefixes of gpio_matrix_in and gpio_matrix_out
to unify those function calls on all supported socs.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Current impĺementation fails due to missing stop bit
when reading data. This fixes it and refactor the implementation
by adding k_busy_wait when waiting I2C bus completion.
Also, this implementation is based on esp-idf v3.0.
It will be refactored based on latest esp-idf v4.3 using proper
low level calls.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Fixes#34015
Now that we generate a header that extern's all possible devicetree
based device struct we can remove DEVICE_DT_DECLARE and
DEVICE_DT_INST_DECLARE as they aren't needed anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Disable RTC WDT enabled (by default) by 2nd stage bootloader in ESP-IDF.
This WDT timer ensures correct hand-over and startup sequence from
bootloader to application.
Enabling bootloader caused system clock initialization to fail
when clock rate is greater then 80MHz. This also fixes
esp32 clock source code.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- Change default CPU Clock to 240MHz
(PLL is activated)
- I2C, UART will use sysclk from clock driver
- esp32_enable_peripheral replaced by
clock_control_on
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There are issues using lowercase min and max macros when compiling a C++
application with a third-party toolchain such as GNU ARM Embedded when
using some STL headers i.e. <chrono>.
This is because there are actual C++ functions called min and max
defined in some of the STL headers and these macros interfere with them.
By changing the macros to UPPERCASE, which is consistent with almost all
other pre-processor macros this naming conflict is avoided.
All files that use these macros have been updated.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
The Kconfig symbols for RX/TX LSB first didn't match between the driver
and the Kconfig file. Change driver to match Kconfig symbol names
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
irq_lock returns an unsigned int, though, several places was using
signed int. This commit fix this behaviour.
In order to avoid this error happens again, a coccinelle script was
added and can be used to check violations.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
On 'drivers/i2c_esp32.c' there are functions useful for other
drivers. Functions and struct went moved to:
* arch/xtensa/soc/esp32/peripheral.h
* arch/xtensa/soc/esp32/soc.h
* include/drivers/gpio/gpio_esp32.h
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
to_read is the minimum value between I2C_ESP32_BUFFER_SIZE
and (msg.len - 1) rather than the maximum value.
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
When I2C Master writes to slave on CMD_Controller, opcode WRITE
was set twice instead of 1 WRITE at the beginning of the
transmission.
And when Master reads from slave, on CMD_Controller,
byte_num = 1 + data_lenght instead of byte_num = 1 at the
beginning of the transmission.
Note that is for 7 bits addresses, to 10 bit adressess is added
more 1 in byte_num as can be seen in the code above this fix.
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
