spi1 and i2c0 share peripheral ID number 3.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
UART0, TWI0, and SPI0 have different peripheral IDs (2, 3, and 4
respectively) on this SoC and therefore should not be mutually
exclusive to use.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
There is a choice to log btmon logs over UART or RTT.
You can choose number of RTT buffer, set its name and size.
Replaced CONFIG_BT_DEBUG_MONITOR with CONFIG_BT_DEBUG_MONITOR_UART
for UART usage and CONFIG_BT_DEBUG_MONITOR_RTT for RTT.
Signed-off-by: Magdalena Kasenberg <magdalena.kasenberg@codecoup.pl>
SMP support on cAVS is implemented by using uncached addresses
for all writable data sections except for stack, i.e. for .data,
.bss and some other specialised ones. So far that has been
implemented for cAVS 1.5. This patch does the same for cAVS 1.8.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
According to RM0041.pdf clock tree for stm32f100xx devices is
different from both STM32F10X density and connectivity lines devices,
but is a combination of both.
Rework symbols definitions so that STM32F100xx is neither of those
and uses:
- CLOCK_STM32_PLL_MULTIPLIER as on SOC_STM32F10X_DENSITY_DEVICE
- CLOCK_STM32_PLL_PREDIV1 as on SOC_STM32F10X_CONNECTIVITY_LINE_...
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fixes an issue with mcuboot where the SoC will freeze when the dpll is
disabled since `atmel_samd_init` was already run in the bootloader.
Signed-off-by: Abram Early <abram.early@gmail.com>
We need to clear interrupt status, before we enable the interrupt.
So I let ite_intc_isr_clear() to be global function.
Signed-off-by: Ruibin Chang <ruibin.chang@ite.com.tw>
Allow SMP processing for SOF on ADSP. Note, that after this
SOF will build with SMP support enabled on all cAVS versions,
but secondary cores will remain disabled unless an SMP
topology is loaded by the host.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
With SOF secondary cores are booted later at run-time instead
of the traditional simultaneous booting of all the cores.
Adjust arch_start_cpu() to make that possible.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
To disable the IDC interrupt on the interrupt controller a bit
must be set in the MSD register instead of clearing the bit in
the MCD register, which has no effect.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
irq_enable() should be called with the composite IRQ code as its
argument, not just the Xtensa proper part of it.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
BT support requires lots of PROVIDE calls that cannot
be added into this linker file. All necessary includes
were moved into hal module to proper handled as needed.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
During configuring the low-voltage power supply of IO pads, the npcx
GPIO driver needs to set the related PORTx_OUT_TYPE bit to 1, i.e.
select to 'Open Drain IO type', also. This CL provides a mechanism that
configuring these bits via 'def-lvol-io-list' node automatically in case
the flag of gpios that have been configured to low-voltage power supply
doesn't contain GPIO_OPEN_DRAIN.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move the STM32F0 specific ram vector table sections into a dedicated
linker snippet included by the new `SRAM_VECTOR_TABLE` symbol.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add a new Kconfig symbol that explicitly controls whether the vector
table should be placed in RAM. This eliminates the side effect of
`IS_BOOTLOADER` controlling vector table location. Making the condition
a positive assertion also allows the config to be used in CMakeLists
conditions (`zephyr_linker_sources_ifdef()`, etc).
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
The NPCX power management code gets a compile error if CONFIG_PM is
enabled but CONFIG_ARM_MPU is disabled.
Signed-off-by: Keith Short <keithshort@google.com>
It was found that npcx7 series' GPIOs which support low-voltage power
supply, there is an excessive power consumption if they are selected to
low-voltage mode and their input voltage is 1.8V.
To avoid this excessive power consumption, this CL suspends the
connection between IO pads and hardware instances before ec enters deep
sleep mode. Then restore them after waking up.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add support for the FVP Base RevC 2xAEMv8A board to be emulated using
the same FVP. For now the virtual platform is only exposing one core and
the basic set of peripherals (GICv3, ARM arch timer, PL011, etc...).
INFO - Total complete: 256/ 256 100% skipped: 933, failed: 0
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The NATIVE_TASK macro uses macros from the toolchain header.
Instead of relaying on the header to be included by somebody else,
include it explicity here.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Fixes#29915.
Implements the memory layout and MPU configuration for Ethernet buffers
for STM32H7 controllers as recommended by ST. 16 KB of SRAM3 are
are reserved for this. The first 256 B are for the RX/TX descriptors and
configured as strongly ordered, shareable memory. The rest is for RX/TX
buffers and configured as non cacheable memory. This configuration is
automatically applied for H7 chips if the SRAM3 memory is enabled in the
device tree.
Signed-off-by: Mario Jaun <mario.jaun@gmail.com>
Optionally configure Kconfig SYS_CLOCK_HW_CYCLES_PER_SEC using
clock-frequency provided by dt if sysclk node is enabled
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To allow transition to device tree based clock configuration on
stm32 targets, rework clock_control driver to use intermediate
STM32_ macros initially defined as the equivalent Kconfig macros
for now.
Propagate the change in all code using these macros.
The reason to introduce these new macros instead of configuring
Kconfig flags using dt kconfigfunctions is that we'll need
to be able to inform users that Kconfig flags are deprecated
once the whole family conversion is done, to encourage
out of tree users to adopt this new configuration scheme.
Note: For now STM32H7 series and code is excluded.
This is the same for some series specific code such as
PLL mul/div for L0/L1 and XTRE prescaler on F1 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This CL adds a override mechanism for pwm module's input clock source
assignment. If the 'clock-bus' property exists, the NPCX_DT_PROP_ENUM_OR
macro function will return an enum upper token value. Otherwise, it
expands to default value in 'clocks' property.
For example, if the users want to select LFCLK as pwm0's input clock,
ths node can be overridden by adding 'clock-bus' property with an enum
string, "NPCX_CLOCK_BUS_LFCLK".
&pwm0 {
status = "okay";
clock-bus = "NPCX_CLOCK_BUS_LFCLK";
};
Signed-off-by: Keith Short <keithshort@google.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Kconfig symbol NFCT_PINS_AS_GPIOS may be defined for all
Nordic nRF SoCs that have the NFCT hardware, so we move
the option definition in nRF common Kconfig file. Also,
we correct the help text to reflect that nRF52 series DKs
and nRF5340 DK have different pins for NFC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds the soc config for the STM32F031k6 and STM32F031X6.
Add the STM32F031k6 as choice to the Kconfig.soc.
Signed-off-by: Sebastian Schwabe <sebastian-schwabe@gmx.de>
