This patch is disabling the dma channel before reloading
source and dest for memory and peripheral addresses
Then the channel is enabled to re-launch the transfer.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace having dts_fixup.h files define DT_ADC_{0..2}_NAME with using
the new devicetree.h macros. We test to see what driver compat is
enabled via DT_HAS_COMPAT and set DT_DRV_COMPAT to that compat. Than we
can utilize the DT_INST_LABEL() macro to extract the name of the device.
We also replace the Kconfig ADC_{0..2} symbols with DT_HAS_DRV_INST.
This will allow us to remove those Kconfig symbols as this was the only
usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_USB* to just USB*.
Also fixup how USB_MAXIMUM_SPEED was defined. We should only define it
if the property exists.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Substitute integral constants where call sites passed named constants
that have timeout values as arguments to parameters that expect
millisecond durations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The goto instruction was removed when adding the RX thread.
While still working, this clearly break the clean handling of
error cases.
Re-instantiate the goto instruction.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
ipm_busy is meant to be used as mutex on transport layer accesses.
Due to wrong configuration on rx_thread, imp_busy was a no-op.
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_LIS2DH_INT* to just LIS2DH_INT*.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_INST_AT2X* to just INST_DT_AT2X*.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_INST_MCP320X* to just INST_DT_MCP320X*.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On cortex M4, AHB clock is equal to SystemCoreClock
On Cortex M7, AHB clock is equal to SystemCoreClock/HPRE
By the way, D1CPRE is of no use when starting from SystemCoreColck.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
TCP contexts are referenced twice,
once for the app and once for the stack.
Since TCP stack is not used for offload,
unref a second time to release the context.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree.
We add a property ('calib-offset') for the SAM{D,E}5x family of SoCs
that is the bit position offset from ADC0 BIASCOMP in the NVM Software
Calibration Area Mapping. For ADC0 this is typically 0 and for ADC1
this will be 14.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the missing prefix z_ required to make the ESP32 version override
the weak implementation.
General practice in ESP32 seems to be to use the MAC address, so
extract that in its canonical byte order.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new path access helpers to avoid hard-coding devicetree paths
in Kconfig, which is a bit messy.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove logging of individual threads spread out throughout the
bluetooth subsystem. The stacks can be analysed by enabling the
following options.
CONFIG_THREAD_ANALYZER=y
CONFIG_THREAD_ANALYZER_AUTO=y
CONFIG_THREAD_ANALYZER_RUN_UNLOCKED=y
Optional:
CONFIG_THREAD_NAME=y
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add a Kconfig option that allows user to set any necessary config
using management interface before interface be operational. A use
case is set the EUI-64 address from an external EEPROM by the
NET_REQUEST_IEEE802154_SET_EXT_ADDR command. After all configs
are done net_if_up() can be invoked to bring interface up.
Fixes#23193.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add local-mac-address on DT and enable it on rf2xx driver. If user
define local-mac-address this value will be used as default mac address.
Otherwise driver automatically add a random mac address.
On application level user can change default mac address using net_mgmt
command with NET_REQUEST_IEEE802154_SET_EXT_ADDR parameter defined on
include/net/ieee802154_mgmt.h header.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fasten events handling by unloading callback treatment.
A RX thread is created. IPM RX events are dumped in a FIFO
which is processed in the thread context.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options and dts fixups for GPIO instances.
A side-effect to using DT_INST_FOREACH is that GPIO ports A0 and A3
are now enabled, whereas they were originally disabled by default as
an optimization.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Changing more of DT_* prefixed macros that refer to instances to use
DT_INST macros in GPIO, I2C and UART drivers.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert various DT_DTCM_* macros to use DT_CHOSEN(zephyr_dtcm) and
associated macros from devicetree.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert pinmux driver to use nodelabels to get references to devicetree
nodes using the new devicetree.h macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
