In case of dualcore, STM32H7, STM32W and STM32MP1,
protect concurrent register write access with HSEM.
Done for following drivers:
clock_control, counter, flash, gpio, interrupt_controller
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This patch set the EXTI line 17 as the RTC alarm pin
on the stm32f2x serie from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace individual device instance definitions with the macro that
expands to the equivalent change.
F='struct device DEVICE_NAME_GET'
git grep -l "$F" \
| xargs sed -i -r \
-e "s@$F"'\(([^)]*)\);@DEVICE_DECLARE(\1);@'
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add +1 tick to alarm in order to compensate the partially started tick.
Alarm will expire between requested ticks and ticks+1.
In case only 1 tick is requested, it will avoid that +1 Tick event
occurs before alarm setting is finished.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The driver-specific config_info structure referenced from the device
structure is marked const. Some drivers fail to preserve that
qualifier when casting the pointer to the driver-specific structure,
violating MISRA 11.8.
Changes produced by scripts/coccinelle/const_config_info.cocci.
Some changes proposed by the script are not included because they
reveal mutation of state through the const pointer, though the
code works as long as the driver-specific object is defined without
the const qualifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
init_fn is not anymore part of struct device, so let's test instead the
driver's API structure pointer which is also unique per device driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The DS3231 is an I2C real-time clock with internal temperature
compensated oscillator, maintaining civil time to 1 s precision with
nominal 2 ppm accuracy from 0-40 Cel.
The basic functionality is exposed as a counter that is always running
at 1 Hz. Much more functionality is exposed as driver-specific API,
including the ability to translate between the time scale of the DS3231
and the time scale of the Zephyr uptime clock. This allows correlation
of events in the system clock to UTC, TAI, or whatever time scale is
used to maintain the DS3231.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree. Move the prescaler setting
from Kconfig to devicetree as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These drivers use legacy DT APIs to access data by node label. Update
them to use the new API.
Leave the existing Kconfig options in place. This helps with
bisectability in case of regressions and lets us proceed
incrementally. Removing the per-instance Kconfigs is also nontrivial
in these cases because of hard-coded dependencies in other subsystems.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Add counter driver for the NXP Kinetis Low Power Timer (LPTMR). The
driver can be configured either as 16 bit counter or 16 bit pulse
counter.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert older DT_INST_ macro use in microchip drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in silab drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
z_vrfy_counter_get_value should check the size of memory pointed to
ticks and not the size of the pointer.
Fixes: #22431
Coverity CID :207984
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Convert driver to use DT_INST_ defines.
Removed DT_RTC_0 fixup macros but keep DT_RTC_NAME_0 as it is
still in use across RTC users.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable counter driver support for H7 series. Tested with H743ZI MCU
using samples/drivers/counter/alarm.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Convert driver to use DT_INST_ defines. The preferred defines for
drivers are DT_INST_.
As part of this change we utilize the device tree for GIRQ info and
rename timer3 to 2 since we are doing this by instance number.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. Replace dts_fixup.h use
for DT_RTC_0_NAME with DT_INST_0_NXP_KINETIS_RTC_LABEL to be
consistent. Also, remove the aliases that had been used for this
driver in various nxp_k*.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines and remove Kconfig per instance
enablement in favor of DT_INST_ define existing. Also, remove the
aliases that had been used for this driver in nxp_rt.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Introduce a new counter API function for reading the current counter
value (counter_get_value()) and deprecate the former counter_read() in
favor of this.
Update all drivers and calling code to match the new counter API.
The previous counter driver API function for reading the current value
of the counter (counter_read()) did not support indicating whether the
read suceeded. This is fine for counters internal to the SoC where the
read always succeeds but insufficient for external counters (e.g. I2C
or SPI slaves).
Fixes#21846.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Refactors the mcux rtc driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux gpt driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The GPT based counter is a count up timer.
This fixes counter_basic_api tests.
Fix over 80 chars coding style issue.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
