Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We don't need to define DT_NUM_IRQ_PRIO_BITS or DT_NUM_MPU_REGIONS in
dts_fixup.h files anymore, so we can remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit enables the GMAC Ethernet support for the `atsame54_xpro`
board which includes an on-board RMII PHY.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
In order to use its serial peripheral SERCOMs SAMD socs require their
pins to be configured with pinmux. Currently pins are muxed only for the
boards' default serial interfaces. The pinmux code is written to throw
a compiler error if a user tries to use any sercom in a way it wasn't
pre-defined to be used.
This commit changes compiler errors to warnings so that user can provide
custom pinmuxing code in their app.
Fixes#23133
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
This commit enables the newly added GMAC instance in the `sam4e_xpro`
device tree.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This enable GMAC driver by default if the end application selects
NETWORKING. The driver will set MII interface since is the only one
available for SAM4E and will select a random MAC value.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This board contains an on-board Winbond W25Q16.
The chip is connected to spi1 using PB3-PB5 and PB0 as CS.
Signed-off-by: Bjarne Steinsbo <bjarne@gmail.com>
While the Cortex-R arch port does not currently support memory
protection and userspace, the `memory_protection` and `userspace` test
tags should not be ignored because doing so can unintentionally disable
other relevant tests.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This adds the support of openocd for nucleo board stm32g474re
It requires the openocd that supports stm32G4xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the support of openocd for nucleo board stm32g431rb
It Requires the openocd that supports stm32G4xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the support of openocd for nucleo board stm32g071rb
It requires the openocd that supports stm32G0xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards moving uart mcux driver to DT_INST based, we need to convert
uses of CONFIG_UART_MCUX_[0-9] to use DT_NODELABEL instead. This way
the pinmux settings are still based on specific instances of the uart.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit fixes the incorrect memory (FLASH and SRAM) size
specification in the device tree and the board test yaml files.
The `qemu_cortex_r5` board (using `fdt-single_arch-zcu102-arm.dtb` FDT)
has 64MiB RAM at the address 0 and 32MiB QSPI flash at 0xc0000000.
QEMU `info mtree`:
0000000000000000-ffffffffffffffff (prio 0, i/o): memory@00000000
0000000000000000-000000000002ffff (prio 0, ram): ddr_bank1_1@0x0
0000000000030000-000000000003ffff (prio 0, ram): ddr_bank1_2@0x30000
0000000000040000-0000000003ffffff (prio 0, ram): ddr_bank1_3@0x40000
00000000c0000000-00000000c1ffffff (prio 0, i/o): lqspi
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use the new devicetree API. Remove per-board enabling of ADC_0 by
setting ADC_0 to default y when the 'adc' node label points at an
enabled node of the expected compatible (depending on SoC).
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Those are used only in tests, so remove them from kernel Kconfig and set
them in the tests that use them directly.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as usart. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as i2c. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This change ensures that shared memory doesn't hold any pre-reset
values after Soft reset is issued. When the Network Core boots up,
shared memory is always set to zero.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Convert stm32 entropy driver to configuration based on device tree.
Select HAS_DTS_ENTROPY symbols and configure CONFIG_ENTROPY_NAME
in fixup files.
Since rng node is not enabled (or available) on all boards, it could
happen that symbol ENTROPY_STM32_RNG is not enabled and hence
ENTROPY_HAS_DRIVER not selected which ends up with a symbol
ENTROPY_NAME defined throufg Kconfig selection. Thus, in fixup file,
CONFIG_ENTROPY_NAME is defined only if not already defined.
Additionally, update boards that used to configure entropy by default.
On these boards, enable rng device in device tree and remove Kconfig
related configuration (which should not be part of default
configuration).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Correct the documentation page title for the
nRF9160 DK, to match the official Dev-Kit name.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We rename the nRF53 Dev Kit board target (nrf5340_dk_nrf5340)
to nrf5340pdk_nrf5340. We update all associated references
in the supportive documentation and all nRF5340-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The board name for the Thingy:52, so far known as nrf52_pca20020, is
renamed to thingy52_nrf52832. Its documentation and all references to
its name in the tree are updated accordingly. Overlay and configuration
files specific to this board are also renamed, to match the new board
name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52840 Dongle, so far known as
nrf52840_pca10059, is renamed to nrf52840dongle_nrf52840. Its
documentation and all references to its name in the tree are updated
accordingly. Overlay and configuration files specific to this board are
also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52833 DK, so far known as nrf52833_pca10100,
is renamed to nrf52833dk_nrf52833. Its documentation and all
references to its name in the tree are updated accordingly.
Overlay and configuration files specific to this board are also
renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board target for emulation of nRF52810 on nRF5DK, so far
known as nrf52810_pca10040, is renamed to nrf52dk_nrf52810.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF51 Dongle, so far known as nrf51_pca10031, is
renamed to nrf51dongle_nrf51422. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to match
the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a reference to the PCA number to help users identify the board and
for consistency with the rest of the boards.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>