Add support for building and running the BT tester on the
nrf5340_audio_dk.
This is copying the configuration used for the nRF5340 DK.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Test was failing because after re-enabling QDEC there is an interrupt
REPORTRDY coming after some time. Test had k_msleep(100) added to
accomodate for that but it was added after sensor_sample_fetch and
should be added before so that sample with data from REPORTRDY event
is fetched so that next read is empty as expected.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
This patch adds tests for the wifi_credentials library.
Both the main functions and the backend implementations are tested.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Added the battery critical status char to bas service
as per bas_1.1 spec. Updated BSIM test for BAS service
to test the INDs of BAS critical characteristic.
Signed-off-by: Nithin Ramesh Myliattil <niym@demant.com>
This makes sure we always fit all configurations. Worst case is two
audio streams in 48_6 configuration in single ISO channel (2x155).
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
For now this seems to be required by PTS as there is not Upper Tester
action for this in Test Specification.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Add wsen_hids_2525020210002 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Add test suite which uses GPIO loopback to produce a "very low" and
"very high" voltage at the positive input of the comparator using the
output of a GPIO. The negative input is set to a voltage between the
high and low output voltages of the GPIO using whichever internal
reference is available to the comparator.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Add functionality to test the IGMP query handling. This test should
prevent the IGMP logic from sending IGMPv3 messages to IGMPv2 queriers.
The test does now also check backwards compatability when IGMPv3 queries
are received but only IGMPv2 is enabled.
Signed-off-by: Ibe Van de Veire <ibe.vandeveire@basalte.be>
In a uniprocessor system, _sched_spinlock may not need to be
held in all the same cases that it does in a multiprocessor
system. Removing those unnecessary usages can lead to better
performance on UP systems. In the case of uncontested taking
and giving of a semaphore, this can be as much as a +14%
performance gain.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
The production version of the nRF54L15 SoC is now available, so remove
the initial Engineering A (EngA) preview version.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A bunch of copy-paste mistakes when adding the nRF54L15 DK added stale
references to the Preview DK (PDK).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a test that checks behavior of
CONFIG_BT_CONN_CHECK_NULL_BEFORE_CREATE Kconfig option.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Some devices may belong to >1 power domain, so with the current design
this is something not possible to describe. It's worth to note that
Linux also uses the `power-domains` naming scheme, not `power-domain`.
This patch also introduces `power-domain-names` so that each entry in
`power-domains` can be given a name if needed. `#power-domain-cells`
is now required as well.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Change integration_platform -> platform_allow to not build the
shell test suite for all supported boards.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
retained_mem driver is now compatible with nrf54h20 cpuapp & cpurad.
Also add missing .conf for nrf54l15.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Tests for prometheus library support.
It contains integration and unit test
each metric types.
Signed-off-by: Mustafa Abdullah Kus <mustafa.kus@sparsetechnology.com>
Enable dma boards/test for S32Z270.
The non-cacheable memory used for DMA tests (chan_blen_transfer and
loop_transfer) is split from the system SRAM.
Signed-off-by: Ha Duong Quang <ha.duongquang@nxp.com>
Consistently use the nRF54L15 as the non-TF-M integration platform
in addition to `native_sim`, and the nRF9151 as the TF-M one.
In addition, add the `integration_platforms` specification to the
tests that were missing it.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Fix errors found in CI for missing clock_t and clockid_t types
when building the tests/posix/net testsuite against newlib.
Also use angle-brackets and prefixed path with
`<zephyr/posix/posix_types.h>` since it is not in the default
search path and is analagous to `<sys/types.h>`.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
It's more common (and more readable) convention to use lower-case
names for string-based device tree property values. Convert the HCI bus
and quirks to follow this convention. Also take advantage of the
recently added support for string-array enums to enforce that the
correct values are used.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
1. add delay read config for platforms that has capacitor with pin
2. add dts pin flags to gpio_pin_config when output.
Signed-off-by: Hake Huang <hake.huang@nxp.com>
update boards that can not use the common pins
mimxrt102x reuse with ethernet
mimxrt106x has external pull up
lpcxpresso55s3x reuse with int
add CONFIG_SKIP_PULL_TEST by default to be more general
user can enable this test in customized case with select pin
ST prefer to using D9 D10 pair to testing.
Signed-off-by: Hake Huang <hake.huang@nxp.com>
This allows to run the test 'chan_blen_transfer' and 'loop_transfer' on
the sgrm board.
The functionality tested in `chan_link_transfer` and `scatter_gather` is
not (yet) supported by the Si32 DMA driver, and those tests therefore
not enabled.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
