When CONFIG_NOCACHE_MEMORY=y, the .nocache section is placed in between
__rodata_region_end and _app_smem_start/__kernel_ram_start. Make sure
this region is covered by the MPU background region so that the static
region for nocache is configured correctly.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Introduce the new stm32h5 soc serie from STMIcroelectronics.
Note that stm32h503x do not have TrustZone nor SAU
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove the manually created linker section, because it's already
automatically generated for all sram regions in the DTS with the
"zephyr,memory-region" compatibility.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Change device tree VW routing to a form allowing overrides.
Add two new DT optional properties for specifying the reset
source and reset value of each virtual wire. Only virtual
wires that are enabled using the status property are modified.
NOTE: eSPI virtual wires are controlled in groups of 4 by
hardware. The optional reset signal source properties applies
to all four virtual wires in the group. If this field is
changed from the hardware default, it should be changed for
only one virtual wire in the group. If the property exists
in more than one wire in the group it must be set to the
same value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Modify Mircrochip MEC172x eSPI driver to get eSPI virtual wire
hardware routing from device tree.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The clock control driver requires three pieces of information:
PCR register index, bit position, and clock domain. Clock domain
was missing from DT information and MCHP macros.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Some pico-sdk drivers call a panic function, originally implemented
as part of the Pico's C runtime. This commit adds a Zephyr compatible
implementation of panic, so that those drivers could be compiled with
Zephyr.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Add initial version of clock control for Atmel SAM SoC series. This add
support to Power Management which allows control peripherals clock.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Product URL: https://www.ti.com/product/CC1352P7
Datasheet : https://www.ti.com/lit/ds/symlink/cc1352p7.pdf
Features:
Powerful 48-MHz Arm® Cortex®-M4F processor
* 704KB flash program memory
* 256KB of ROM for protocols and library functions
* 8KB of cache SRAM
* 144KB of ultra-low leakage SRAM with parity for
high-reliability operation
* Dual-band Sub-1 GHz and 2.4 GHz operation
Updates:
* Remove CC1352P7_LaunchXL due to compliance checks
* Add CC1352P7 updates
* Update hal_ti for CC1352P7 support
* Remove blank line at end of modules/Kconfig.simplelink
* Split struct and typedef for pinctrl_soc_pin/pinctrl_soc_pin_t
* Reference cc13x2_cc26x2/pinctrl_soc.h
* Reference cc13x2_cc26x2/soc.h
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
In general, RTC and TIMER driver implements counter API but there
are exception when those peripherals are used in a custom way
(e.g. for system timer or bluetooth). In that case, system must
prevent using counter based on a reserved instance. Previously,
it was managed by Kconfig options but that cannot be maintained
when switching to devicetree configuration of the counter driver.
A new approach removes Kconfig options and instead adds static
asserts in the files which are using direct peripherals. Those
asserts check if given node is not enabled in the device tree.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Removed the EEPROM and ESPI configuration from file
Kconfig.defconfig.mec172xnsz. Since it overrides the
setting present in the Device Tree file.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Use Device Tree bindings to configure clock source/frequency for enabled
UARTs only.
Get rid of UART clock ungating from `soc.c`, as that functionality has
been moved to the clock controller.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
Add functionality for changing the code location
based on the flash chosen node for RT devices.
Remove obsolete Kconfigs that used to be used
to set the code location for RT devices.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Allow selecting between direct SMPS and LDO on the startup. This
enables selecting to use SMPS regulators which can save bit of power.
Signed-off-by: Miika Karanki <miika.karanki@vaisala.com>
The STM32H730 series has a variant built with SMPS. It uses
`stm32h730xxq.h` header file instead of `stm32h730xx.h`, which has the
SMPS macro defined.
This commit adds the `SOC_STM32H730XXQ` configuration option to allow
the build system include the proper header file. With this change,
boards can enable `CONFIG_POWER_SUPPLY_DIRECT_SMPS` to set up the power
supply for the CPU.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Add clock initialization for MIPI and LCIDF to NXP RT5xx SOC.
Note that clock divider properties are used by both initialization
routines, as the required clock divider will vary depending on
attached display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This is a follow-up to commit 7195db01f4.
Restore the check that was accidentaliy removed in the above commit,
so that the message is again logged only once per detection of the
anomaly 160 conditions.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit fe3b97a87f.
This message should not be a warning, as it does not actually indicate
that something potentially bad happened. On the contrary, it informs
that conditions in which the anomaly 160 could occur were detected and
the anomaly was prevented from occurring. There is no need for this
message to appear in the default configuration (INFO level). In fact,
the message would undesirably flood the console in some cases (like
the kernel/mem_protect/stack_random test) and sometimes it would also
require enlarging the stack of the idle thread (the function is called
underneath k_cpu_idle()). Therefore, the logging level of this message
is changed to DEBUG.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Added initial version of Infineon CAT1 Pin controller driver.
Added initial version of binding file for Infineon CAT1 Pinctrl driver.
Added initial version of dt header for Infineon CAT1 pinctrl driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Since PINCTRL and pinctrl-0 is now required, there's no point in doing
extra validation at driver level. Modify the macro to just check that
sleep state is present when needed, since it was the only remaining
assertion that was not covered. Renamed the macro to make it more clear
what it does: NRF_DT_CHECK_NODE_HAS_PINCTRL_SLEEP
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Drop the non existing option PINMUX_XEC, this has been removed in
d76f4f2c8a drivers: pinmux: mchp_xec: drop driver
And is currently causing build errors.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add the stm32U5 serie for the support of the STM32_BACKUP_SRAM
The PWR peripheral is enabled by the soc/arm/st_stm32/stm32u5/soc.c
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This is a follow-up to commit fe3b97a87f.
Add a cmake warning issued when the workaround for the nRF5340 anomaly
160 cannot be applied because the application is configured with no
system clock.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Drop STM32 pinmux driver in favor of pinctrl. Some definitions located
in pinmux headers were used by the pinctrl driver, so they have been
moved there.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Cleanup core if booting from bootloader using RT5xx. This is required
because the call to SystemInit will push data to the stack, and the
bootloader may have configured stack limits or MPU settings. Either
would cause the core to fault if these settings are not first
cleaned up.
Perform this cleanup if the boot header is not present, as in this case
the application was likely kicked off via a bootloader.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Allow to include boot header for code linked into
not only FlexSPI controlled memory.
Fixes#53867
Signed-off-by: Mikhail Siomin <victorovich.01@mail.ru>
Implement a workaround for the nRF53 anomaly 160. This consist of
a set of writes to certain hardware registers that is done at boot
and a piece of code that is executed when the CPU is made idle and
that prevents the CPU from switching between active and sleep modes
more than five times within a 200 us period.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use CMSIS SystemInit for all NXP iMX.RT SOCs, to simplify initialization
flow, and remove redundant code where possible.
Introduce Kconfigs to disable Cache at boot, since SystemInit will enable
code cache on these platforms, which may be undesirable behavior.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert NXP LPC SOCs to use CMSIS SystemInit, and remove redundant code
where it exists. This will enable initialization flows to be more
standardized across all platforms.
Since LPC54xxx and LPC55xxx series enables SRAM banks in SystemInit,
provide Kconfigs to bypass this setting and keep additional SRAM
banks unclocked.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add call to SystemInit for all NXP Kinetis SOCs and remove any
redundant code from initialization flow. This allows watchdog
initialization to be removed from all Kinetis SOCs as it is handled
by SystemInit.
Since Kinetis watchdog is enabled by default at boot, allow watchdog
setup to by bypassed with CONFIG_WDOG_ENABLE_AT_BOOT. This
setting requires the user to provide a watchdog configuration hook
using z_arm_watchdog_init, but will allow the watchdog to remain
enabled.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
update the endpint in dts to 6 to alignd with RM
enable usb-device for LPC55S28
all USB supported tests/samples PASS
samples:
scripts/twister -p lpcxpresso55s28 \
--device-testing --hardware-map ~/map.yml \
-T samples/subsys/usb/
...
INFO - 7 of 25 test configurations passed (100.00%),\
0 failed, 18 skipped with 0 warnings in 73.49 seconds
...
tests
scripts/twister -p lpcxpresso55s28 \
--device-testing --hardware-map ~/map.yml \
-T tests/subsys/usb/
...
INFO - 3 of 4 test configurations passed (100.00%),\
0 failed, 1 skipped with 0 warnings in 36.39 seconds
...
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Allow the the SoC to enter deep sleep when CONFIG_PM_DEVICE
is enabled. This will allow to selectively add low power
support for certain drivers like UART and ADC.
The previous checking of ifndef CONFIG_PM_DEVICE was
incorrect. The MEC172x requires the soc power file to perform
some operations when CONFIG_PM_DEVICE is enabled to allow
the hardware to shut down the PLL.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
PR #30403 implemented nocache regions for ethernet DMA buffers in sram3 to
fix issue #29915. Unfortunately, some STM32H7 variants do not have any
sram3 so they still suffer from #29915.
All H7 variants have sram2 though, so use that for targets without sram3.
Signed-off-by: Björn Stenberg <bjorn@haxx.se>
