Setting clock-frequency as required (the driver does not build without
it) and dropping definitions that are already specified in
i2c-controller.yaml.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Replace few instances of space before colon in the binding files, not
functional, just for coherency.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
STM32L152xC SoC differs from other L1 SoCs in RAM (32KiB) and
flash (256KiB) size, EEPROM size (8Kib) and amount of interrupts
(57, see STM32Cube). Devicetree and Kconfig support.
Signed-off-by: Noelle Clement <noelleclement@hotmail.com>
after 7c699348a8
Convert drivers to new DT device macros
now the device name is aligned with label so we need
align them to default config
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
This patch adds IRQ priority support for SiFive PLIC by device-tree.
Some IRQ sources of plic use Kconfig to set priority of their IRQ.
- AON: no driver
- I2C, SPI, PWM: not use IRQ
- GPIO, UART: default 1
So this patch specifies IRQ priority 1 for all sources.
Currently these drivers (gpio and uart) do not support that they get
and use IRQ priority from device-tree. We need more patches.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
The npcx7m6fb dts defines i2c controller and ports, where the controller
is a property in the port node definition and the device nodes should be
defined as subnodes of the port.
This changes the binding definitions to reflect that, defining the port
as an i2c-controller so that in can inherit sub-nodes for i2c devices,
and the controller as a generic node.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
jedec,jesd216.yaml has properties for any memory device that conforms
to the JESD216 specification. This file at a minimum should be
included in the binding for any driver that interacts with such a
device.
jedec,spi-nor-common.yaml extends jedec,jesd216 with additional
parameters useful for memory devices that are not available from
standard JESD216 parameter tables. This file may be included instead
of jedec,jesd216.yaml if a driver is able to support additional
functionality related to the extended description.
jedec,spi-nor.yaml remains the binding for the Zephyr SPI_NOR driver
alone.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add binding for the Nordic ECB (AES electronic codebook mode
encryption) peripheral and corresponding devicetree nodes for
nRF SoCs that feature this peripheral.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Since MDK was updated and now it contains the definition of QDEC
peripheral for nRF52805, the DT node representing this peripheral
can be processed normally.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
"st,mem2mem" property is supposed to be limited to dma-v1.
Remove its use in dma-v2 components.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2 versions of DMA hardware blocks could be found across stm32 series.
In order to simplify the handling of matching Kconfig symbols,
make this visible in dts files by creating "st,stm32-dma-v1" and
"st,stm32-dma-v2" and set them accordingly in dtsi files.
Duplicate and update related bindings to reflect that new state.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Tigerlake H has less RAM and fewer cores. Both should be
supported, selectable at the board level. For now use the H
configuration as more readily available for testing.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
The STM32F105xx is effectively an STM32F107xx without Ethernet. As such,
it's possible to include the STM32F105's device tree from STM32F107, and
add in any additional nodes (currently just DMA2, though according to
the datasheet, this may be supported by the STM32F105xx and other parts
too).
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
Create a common binding file that will be included by all bindings
handled by iis2dlpc driver. For now this includes optional drdy-gpios
property and it is shared by the i2c and spi version of the driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The interrupt numbers for two socs for the gpio peripheral was wrong.
This commits corrects this issue for the relevant socs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
The watchdog and rng nodes were a sub-node of the gpio node.
This commits corrects this issue for the relevant socs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds support for ADC on G0 series.
Simple implementation: sequencer not fully configurable,
and only one common sampling time.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
There are some drivers in the tree that support devices on multiple
different buses, although so far this has not been represented in
device tree using the bus concept. In order to convert these drivers &
bindings to refer to a formal bus in device tree we need to be able to
match bindings which lack an explicit "on-bus: ..." value against any
parent bus. This will also be needed for any external bindings, since
those would not be aware of on-bus (as it's a Zephyhr-specific
extension).
The two drivers I'm particularly targeting is the ns16550 UART driver
(drivers/serial/uart_ns16550.c) and the DW I2C driver
(drivers/i2c/i2c_dw.c). They both support devices with a fixed MMIO
address as well as devices connected and discovered over PCIe. The
only issue is that instead of encoding the bus information the proper
DT way these bindings use a special "pcie" property in the DT node
entries to indicate whether the node is on the PCIe bus or not.
Being able to convert the above two drivers to use the DT bus concept
allow the removal of "hacks" like this:
if DT_INST_PROP(0, pcie) || \
DT_INST_PROP(1, pcie) || \
DT_INST_PROP(2, pcie) || \
DT_INST_PROP(3, pcie)
to the more intuitive:
if DT_ANY_INST_ON_BUS_STATUS_OKAY(pcie)
This also has the benefit that the driver doesn't need to make any
arbitrary assumptions of how many matching devices there may be but
works for any number of matches. This is already a problem now since
e.g. the ns16550 driver assumes a maximum of 4 nodes, whereas
dts/x86/elkhart_lake.dtsi defines up to 9 different ns16550 nodes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the driver for Omnivision OV7725
Color CMOS VGA Sensor.
The driver currently provides a simple capture
function, the output format only provides
RGB565,640x480.
Signed-off-by: Frank Li <lgl88911@163.com>
This patch enables the rtc clock on the stm32g4 soc
from STMicroelectronics.
Even if the set by default (reset value of theRCC_APB1ENR)
the bit is marked as 1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Instead of hard-coded values for interrupt priorities in DT nodes, use
a macro that additionally can be overridden at the board or application
level. This allows, for instance, changing the interrupt priorities for
all but one peripheral without using a lengthy overlay file.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This file originally added a "nordic,nrf-sw-pwm" node with a few basic
properties that were common to all nRF51 and nRF52 series SoCs. There
is no implementation of SW_PWM available for other nRF series. At the
time this file has been created, there was only nRF91 apart from nRF5x,
but when nRF53 appeared, the name of this file became misleading.
Recent addition of common disabling of the systick node made it clear
that such common file for all nRF SoCs is convenient.
To prevent further confusion, rename this file to nrf_common.dtsi and
keep there only stuff actually common to all nRF series, moving the
SW_PWM related node to particular SoCs that use it (this is actually
consistent with how all other nodes, that also have some properties
common to several or even all nRF SoCs, are defined).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Change io status of host-uart device to "disabled". It was caused by a
mistake during solving conflicts.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add a new display-inversion property to ili9xxx based display drivers to
send a "Display Inversion ON (0x21)" command during initialization.
This seems to be required for some ILI9xxx based displays to work
correctly, such as BuyDisplay ER-TFT028A2-4 (ILI9341 basd IPS display).
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Define a binding for zephyr,fstab which contains multiple child nodes
each of which identifies a file system type and configuration
parameters and associates it with a fixed partition. The base entry
properties specify the mount point and other generic fs mount options,
while bindings specific to a file system type provide the
configuration parameters necessary to describe the file system.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This change adds support for configurable interrupt capabilities
in the emulated GPIO controller via Devicetree bindings.
Fixes#26477
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
The NPCX SMB modules provides full support for a two-wire SMBus/I2C
synchronous serial interface. Each SMBus/I2C interface is a two-wire
serial interface that is compatible with both Intel SMBus and Philips
I2C physical layer. There are 8 SMBus modules and 10 buses in NPCX7
series.
In NPCX7 series, the SMB5 and SMB6 modules contain a two-way switch to
support two separate SMBus/I2C buses (ports) with one SMB module
(controller) Please refer Section 4.7.2 in the datasheet. In order to
support it, this CL seperates the i2c driver into port and controller
drivers. The controller driver is in charge of i2c module operations
and internal state machine. The port driver is in charge of pin-mux
and connection between Zehpyr i2c api interface and controller driver.
All of modules have separate 32-byte transmit FIFO and 32-byte receive
FIFO buffers. These FIFO buffers reduce firmware overhead during long
SMBus transactions by allowing the Core to write or read more than one
data byte at a time to/from the SMB module.
The CL also includes:
— Add npcx i2c port/controller device tree declarations.
— Zephyr i2c api implementation.
— Add "i2c-0" aliases in npcx7m6fb.dts for i2c test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The System Glue module includes the three major functions:
— Power Switch Logic (PSL)
— SMBus multi-bus, wake-up support
— Simple Debug Port (SDP)
In NPCX7 series, the SMB5 and SMB6 modules contain a two-way switch to
support two separate SMBus/I2C buses (ports) with one SMB module
(controller). Since a single SMB module is able to serve only one
SMBus/I2C bus at a time, SMB_SEL registerin Glue module is used to
control theconnection of I2Cn_0 and I2Cn_1 interface pins to the SMBn
module (where n is 5, 6).
This CL provides a soc specific pin-control function called
"soc_pinctrl_i2c_port_sel" to switch buses (port) of the same SMB module
(controller). It will be used in the following i2c driver.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This commit adds the dtsi config for the stm32f303k8.
In addition fixing to long line for author.
Fixing sram0 memory size.
Signed-off-by: Sebastian Schwabe <sebastian.schwabe@mailbox.tu-dresden.de>
