Add clock sources bindings on F0/F3/G0/G4/L0/L1/L4/WB/WL series.
Due to inconsistencies, some common bindings are now split:
F1 -> F0/F1/F3
L4 -> L4/G4/WB
Update .dtsi files when required
In a first step, allowed sources are limited to already supported
clocks: LSI/LSE/HSI/HSE/MSI/PCLK/PLLCLK/SYSCLK
Support for other clocks such as HSI48, SAIXCLK, ... is left for a
next step.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This new binding allows to work on providing stm32u5 specific
alternate and complementary device clocks.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add STM32 clock mux binding.
Only property of a node using such compatible is to
select a clock input.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
e8e88dea incorrectly changed registers
used in `sys_clock_cycle_get(32|64)` functions.
This commit fixes that.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
This is a follow-up to commit 586e26e8fc.
Add missing `qdec0` node labels in definitions of SoCs that have only
one QDEC instance so that the `HAS_HW_NRF_QDEC0` option is properly set
for them. Use the same pattern as in the WDT case and keep the existing
`qdec` labels for backward compatibility.
Also update validation of base addresses so that both QDEC0/QDEC and
QDEC1 are checked.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the UPLLCK clock for the CAN controller as recommended by the Atmel SAM
E70 data sheet.
Move the configuration of the clock prescaler from Kconfig to devicetree
and limit it to the values recommended by the SAM E70 datasheet.
Fixes: #45012
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
In #45014 the m_can compatible identifier was changed from "m-can-base"
to "m_can-base" while #45216 was being developed. This commit updates
the dts for u5 to the latest format.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
In order to bring consistency in-tree, migrate all dts code to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Cleaned up the IPC configuration for nRF5340 SoC in Device Tree. This
change fixes the (simple_bus_reg) warning about the missing or empty
reg/ranges property.
This is a follow-up to commit cf6a58d.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Adds addresses and names for individual CSR registers to device tree.
This way liteuart driver no longer depends on CSR data width being 8
bits.
Also when register names or their number changes, then overlay generated
by LiteX will be incompatible with one defined here.
This should make finding breaking changes easier.
I also appended `_ADDR` suffix to defines, to distinguish them from
normal values like `LITEETH_EV_RX`.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Adds addresses and names for individual CSR registers to device tree.
This way liteuart driver no longer depends on CSR data width being 8
bits.
Also when register names or their number changes, then overlay generated
by LiteX will be incompatible with one defined here.
This should make finding breaking changes easier.
I also appended `_ADDR` suffix to defines, to distinguish them from
normal values like `UART_EX_TX`.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Adds addresses and names for individual CSR registers to device tree.
This way timer driver no longer depends on CSR data width being 8 bits.
Also when register names their number changes, then overlay generated by
LiteX will be incompatible with one defined here.
This should make finding breaking changes easier.
I also updated register names to those used in current LiteX and
appended `_ADDR` suffix to defines which lacked them.
Because register `total` was renamed to `value` and `update_total` to
`update_value` I updated variables accordingly as well.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Add support for the fdcan peripheral to the stm32u5 series device tree
include. This can be applied here since (at present) all of the stm32u5
series MCUs have an FDCAN peripheral.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
All DT nodes end up being part of the generated 'devicetree_unfixed.h'
header, wether they are referenced or not. The number of entries in that
file can grow quickly when using pre-generated pinctrl nodes.
Considering <devicetree.h> (file uncluding devicetree_unfixed.h) is used
in lots of places nowaday, not using /omit-if-no-ref/ can lead to
increased build times.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The OpenISA RV32M1 pinctrl groups need a dummy pinctrl node to populate
with pinctrl options at the board level.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
