Add 'inversion-on' property to st7735r.
Issue INVON(21h) command on initializing if inversion-on was enabled.
As a result of this command, the display color is inverted.
Otherwise, INVOFF(20h) will be issued.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add partial pin control support for the imx8mp. Since the UART driver is
not currently enabled, pin control cannot be tested on this platform.
Therefore, only the DTS definitions required to set the pinmux options
are present for this platform, and are not being applied (since
CONFIG_PINCTRL=n).
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add initial pin control support for the A53 core of the imx8mm. Since
the UART console driver is not currently enabled for this platform,
there is no way to test the full pin control enablement. Therefore,
CONFIG_PINCTRL is still not selected for this platform, although the
required DTS definitions and pin control headers are present.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for IOMUXC peripheral present
on mimx8ml8_m7 soc. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a
new header and compatible binding to handle the
different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for IOMUXC peripheral present
on mimx8mq6_m4 soc. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a
new header and compatible binding to handle the
different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for mcimx7_m4 SOC. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a new header and
compatible binding to handle the different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for mcimx6x. The IOMUXC peripheral present on
this SOC is identical to the one used on the iMX RT10xx series, so the
dts bindings are reused.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add the DTS binding for OCTOSPI interface for the stm32 devices
from STMicroelectronics.
This corresponds to a NOR octo SPI flash.
In this config, there is only on NOR-flash device.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx eSPI and host_subs driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx adc driver. Please notice users need to
configure the corresponding pinctrl nodes in 'pinctrl-0' property in the
adc0 DT node. For example, if ADC0 and ADC2 channels are selected for
the application, please add the follwoings in your board DT layout file.
&adc0 {
status = "okay";
/* Use adc0 channel 0 and 2 for 'adc_api' driver tests */
pinctrl-0 = <&adc0_chan0_gp45
&adc0_chan2_gp43>;
pinctrl-names = "default";
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx tachometer driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in ps2 driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in pwm driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in i2c driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in uart driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL is the initial version for npcx pinctrl driver and introduces
pinctrl nodes for both IO-pads and peripheral devices for each npcx
series. Users can set pin configuration via these nodes in the board
layout DT file. It also wraps all configurations related to pin-muxing
in pinctrl_soc.h. Regarding the other pin properties, we will implement
them later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The drive-mode property is nRF specific, so prefix it with `nordic,`,
same as the `nordic,invert` property.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Removes label and compatible properties
from the flash section. The properties are
provided by included stm32h723.dtsi.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Removes label and compatible properties
from the flash section. The properties are
provided by included stm32h723.dtsi.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
* Corrects SRAM0 size. The `TCM_AXI_SHARED`
is `000` after reset. That means ITCM
is shared with SRAM0.
* Adds missing SRAM1,2,4, and ITCM
regions.
* Adds label and compatible properties
to the flash section.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Enable pin control for lpc11u6x i2c driver, and remove pinmux usage from
board level DTS files.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
convert lpc11u6x syscon clock driver to pin control, and remove all
pinmux usage from driver and syscon dts node.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update pin control driver for lpc11u6x. This SOC does not have a HAL,
so fsl_clock is not available. It also lacks a slew-rate field in the
IOCON register, so this property must be optional.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
switch gpio driver to use pio nodes to configure pin control settings,
and stop using pinmux driver within gpio driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
soc: arm: privilege: add Cyclone V SoC FPGA suppport
Add support for the Intel Cyclone V SoC FPGA (arm Cortex-A9).
Signed-off-by: Esteban Valverde <esteban.valverde.vega@intel.com>
Since implementation of clock source selection in consumer device drivers
could be achieved without usage of a clock-names property and no
example of usage is provided up to now, remove this property from existing
examples.
Additionally, make it clear in stm32 clock control binding that it is
driver's responsibility to correctly access clock source information
and use it as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
