Introduce driver for NXP DCNANO LCDIF (lcd interface) peripheral,
present on iMX.RT500. Currently this driver only supports updating
the primary framebuffer, and does not implement support for the cursor
buffer present on this IP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce driver for MCUX MIPI DSI 2L. This IP block differs slightly from
the existing MCUX MIPI peripheral, and uses a different hardware
abstraction layer. For these reasons, a new driver was introduced rather
than extending the existing mcux_dsi implementation.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Allow configuration of AHB RX buffer allocation. This allows sections
of the AHB RX buffer to be reserved for specific masters, which can
enhance performance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
STM32L432 SDMMC issue
RM0394 :SDMMC
Not available on STM32L42xxx, STM32L432xx and STM32L442xx devices.
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
The driver utilizes ST Microelectronics library (which
exists in modules\hal\st\sensor\vl53l1x. Platform specific
headers and source files used by the library are included
and adapted for Zephyr.
The driver can be configured in proj.conf to use a
interrupt/polling methods and the use of the XSHUT pin on
the VL53L1X. All uses were tested successfully.
Signed-off-by: Mark Watson <mwatson@prosaris.ca>
This patch adds watchdog driver for Renesas Smartbond SOCs.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds driver for SmartBond TRNG peripheral that with separate
ISR an thread data pools.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Add support for configuring power on delay when using SPI SDHC. This
allows cards that reliably initialize with a shorter (1ms) delay to
avoid the long initialize delay otherwise imposed.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add I2C bus recovery support to the STM32 v1 and v2 driver. The STM32 i2c
peripheral does not natively support I2C bus recovery so recovery is
performed using GPIO bitbanging. This mirrors the bus recovery
implementation for NXP MCUX LPI2C driver.
Fixes: zephyrproject-rtos#54917
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
Microchip XEC devices specify GPIO pin using octal numbering and
organize pins in banks of 32. Chip documentation does not use
bank naming rather naming each pin by its octal number. This has
led to the developer having to calculate the bit position of a pin
in its 32-bit bank when a specifying the pin for GPIO usage. We
created a set of defines for all possible GPIO pins that specify
the DT GPIO bank name used in the chip level DTSI files and the
bit position in that bank.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The dma-requests specified for dmamux is changed to
the correct number of 107. This can be found in the
Reference Manual RM0455 Section 17.1.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Extends dmamux driver to support DMAMUX 2,
which supports the BDMA on STM32H7 devices.
Co-authored-by: Jeroen van Dooren <jeroen.van.dooren@nobleo.nl>
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
update MEC172x adc driver to support device PM.
Implement pm resume and suspend actions to put adc
pins in proper state for suspend and resume.
Notify kernel of busy when adc sampling is in progress.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Added initial version of Infineon CAT1 GPIO driver.
Added initial version of binding file for Infineon CAT1 GPIO driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 UART driver.
Added initial version of binding file for Infineon CAT1 UART driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Add initial version of Infineon CAT1 clock control driver.
- supports clock initialization based on board DT configuration.
Added initial version of system_clocks.dtsi for Infineon PSoC 6 SOC.
Includes: clk_imo, path_mux0..4, fll0, pll0, clk_hf0..4, clk_fast,
clk_slow and clk_peri.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 Pin controller driver.
Added initial version of binding file for Infineon CAT1 Pinctrl driver.
Added initial version of dt header for Infineon CAT1 pinctrl driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Devicetree for Infineon PSoC 6 SOC with following
structure:
1. MPN devicetree files
|--> psoc6
|--> mpns
|--> CY8C6016BZI_F04.dtsi
|--> CY8C6036BZI_F04.dtsi
|--> CY****.dtsi
Those file describes cpus, flash-controller, sram memory, nvic option. It
includes the package dtsi (e.g. psoc6_02.124-bga.dtsi) with information
about gpio (based on package e.g. 68-qfn, 128-tqfp, 124-bga, etc.) and
peripherals for (based on PSoC 6 series, psoc6_01, psoc6_02, etc).
MPN devicetree file is main platform dtsi file, which should be included
from board dts (e.g cy8cproto_062_4343w.dts), example:
#include <infineon/psoc6/mpns/CY8C624ABZI_S2D44.dtsi>
2. Devicetree files for PSoC 6 series 02 (2M).
Includes: psoc6_02.dtsi - peripherals dtsi psoc6_01.xxxxx.dtsi - package
dtsi. User does not directly include those files.
It automatically includes via MPN dtsi.
|--> psoc6_02
|--> psoc6_02.dtsi
|--> psoc6_02.100-wlcsp.dtsi
|--> psoc6_02.124-bga.dtsi
|--> psoc6_02.128-tqfp.dtsi
|--> psoc6_02.68-qfn.dtsi
In future PR/commits will be added Devicetree for support all
PSoC 6 series:
- for PSoC 6 series 01 (1M)
- for PSoC 6 series 03 (512)
- for PSoC 6 series 04 (256)
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Provide dts binding for F412 PLL I2S.
This I2S dedicated PLL is fully configurable and take same
input as Main PLL
Only one output clock (PLLR) is supported for now.
This PLL could be found on STM32F412 and F413 parts for instance.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide dts binding for F4 PLL I2S.
This PLL share input source and input M diviso with F4 Main PLL.
Only one output clock (PLLR) is supported for now.
This PLL could be found on STM32F401 parts for instance.
Additionally, provide related header definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Polarity support added to XEC PWM driver. This allows (for example) PWM
controlled LEDs that are active low to actually be turned off when set
to off.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Rework the Host Command support. It includes:
-change API to backend
-change a way of defining rx and tx buffers
-fix synchronization between the handler and backend layer
-simplify the HC handler
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Follow naming pattern in the subsystems(logging or shell) and name
the layer between generic handler and peripheral driver "backend".
The name doesn't suit that well to the SHI backend, because there isn't
SHI API itself and the SHI interface is used only for the host
communication. So the backend code includes the peripheral driver itself.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
