With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Adds a driver for SX1509B I2C GPIO chip. This driver only supports the
basic GPIO features and does not currently implement the LED driver and
keypad matrix features.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Add initial support for STM32L073xZ SOC which is not very different
from already supported STM32L072xZ.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Since not all boards enable all devices, we typically have the SoC dtsi
file have a device marked with status = "disabled" and have the
board.dts explicitly enable with status = "ok". Update it so USB on
Atmel SAMD21 work this way.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree support to the ARM SBCon I2C controller. We utilize
the compatiable "arm,versatile-i2c" the binding from Linux for the some
peripheral block.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The spi nodes should have #address-cells and #size-cells properties much
like i2c does. Add these missing properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most STM32F429 SoCs have 6 SPIs, but STM32F429Vx SoCs only have
4 SPIs. This is one of the rare conditions where device-tree
directive /delete-node/ should be used.
Add spi5 and spi6 node to stm32f429.dtsi. Create file
stm32f429vX.dtsi to delete those nodes and document usage of
/delete-node/ directive.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Some stm32f4 SoCs don't support spi2, so remove spi2
device-tree node from stm32f4.dtsi file.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
stm32f405 is not an expansion of stm32f411, since stm32f411 has more
SPIs than stm32f405.
Fix this by including stm32f401.dtsi in stm32f405.dtsi
(instead of stm32f411.dtsi).
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
The APA102 is a RGB LED with integrated controller. LEDs can be
daisy-chained and use SPI for communication. The SPI port is
configured via Device Tree.
Tested on the Adafruit Trinket M0.
Signed-off-by: Michael Hope <mlhx@google.com>
Configure ccm size and address via dts. According to the DT
specification, the unit-address of a node must match the
first address specified in the reg property of the node.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
stm32f334 is not an expansion of stm32f303, since
stm32f303 has more I2C, SPI ports than stm32f303.
Fix this by including stm32f3.dtsi in stm32f334.dtsi.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
When the Kconfig BOOTLOADER_MCUBOOT is selected, an overlay to place the
image at the slot0 location is required. In order to avoid having to do
this manually for all samples when targetting MCUboot, include the logic
inside the dts.cmake script to prepend a new common.dts file that then
conditionally includes mcuboot.overlay.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit updates the title and the description of the
ARMv6-M, ARMv7-M NVIC dts bindings, so that both the title
and the description reference the respective ARM architecture
and not the Cortex M cores.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This PR includes the required changes in order to support
conditional compilation for Armv8-M architecture. Two
variants of the Armv8-M architecture are defined:
- the Armv8-M Baseline (backwards compatible with ARMv6-M),
- the Armv8-M Mainline (backwards compatible with ARMv7-M).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Added a label for soc-nv-flash nodes. Made some updates to the
generation to maintain creating defines for properties like
erase-block-size and write-block-size so they we get both
FLASH_ERASE_BLOCK_SIZE and FLASH_${LABEL}_ERASE_BLOCK_SIZE (same for
WRITE_BLOCK_SIZE).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for AMS CCS811 Digital Gas Sensor for monitoring
indoor air quality. This sensor reports the following parameters:
1. Co2 concentration
2. VOC concentration
3. Sensor voltage
4. Sensor current
This driver only supports polling mode as of now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This patch changes the manner in which we collect DTS overlay files so
that they comply with the same approach taken for configuration fragment
files (.conf).
Additionally it also documents the usage of those files in the
Application Developer Guide.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds a new optional dts property to define the erase block size of a
flash device. This will be used by the mcux flash driver to implement
the flash page layout function.
The value is set for all kinetis devices to match
FSL_FEATURE_FLASH_PFLASH_BLOCK_SECTOR_SIZE.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
