Convert usb_stm32 driver to use of DT_INST macros.
Since driver is compatible with 3 different dt compatibles and
compatible string is included in DT_INST macros, I've kept the
DT_USB_ compatible agnostic macros based on DT_INST ones, which
allowed to remove fixup definitions.
Use of DT_USB symbols is now limited to usb_dc_stm32.
Additionally, compatible "st,stm32-otgfs" is removed from list
of compatibles for usbotg_hs ips.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32 spi devices, there are 2 main IP variants, with and w/o
fifo. Fifo is not really used today, but still there is some
additional code handling fifo. Today this code is protected under
Kconfig symbol SPI_STM32_HAS_FIFO.
This code carries redundant information vs dedicated compatible
"st,stm32-spi-fifo", which is provided as unique driver compatible
for devices supporting this IP as opposed to use of "st,stm32-spi"
when fifo is not supported.
Having these 2 compatibles defined exclusively is not convenient for
migration to DT_INST as DT_INST macros contain compatible string and
hence it cannot be used to provide common compatible code for devices
defining different compatibles.
Based on these observations, review stm32 spi devices compatible
declarations. Devices supporting fifo will now declare both
compatibles, as proposed by dt spec: "[compatible] property value
consists of a concatenated list of null terminated strings,
from most specific to most general". Hence field will now be:
"st,stm32-spi-fifo", "st,stm32-spi"
This way, fifo enabled stm32 spi devices will generate both:
DT_INST_STM32_SPI_FOO and DT_INST_STM32_SPI_FIFO_FOO
As well as:
DT_COMPAT_ST_STM32_SPI and DT_COMPAT_ST_STM32_SPI_FIFO
So, DT_INST_STM32_SPI_FOO could be used for device initialization.
Also DT_COMPAT_ST_STM32_SPI_FIFO could be used for FIFO handling
code inside driver. Hence use it to replace Kconfig symbol
SPI_STM32_HAS_FIFO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a property to the nxp,kinetis-gpio binding that related the GPIO
node to the pinmux PORT node.
For the kl25z we add the pinmux nodes as well since they didn't exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enable counter driver support for H7 series. Tested with H743ZI MCU
using samples/drivers/counter/alarm.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Change to code to use the automatically generated DT_INST_*
defines and remove the now unneeded configs and fixups.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Introduction of tachometer device nodes for the Microchip
MEC1501 SOC. In addition, dts bindings for are also introduced.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
LPC55S69 CPU1 definition added.
Dual Core is not enabled!
Definitions related to dual core split of SoC's CPUs.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add the girq and girq-bit fields to the binding. This allows
encoding GIRQ related information inside device tree.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The max-value should just be an int and not an array. Change the type
to 'int' in the binding and fixup the driver to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. Replace dts_fixup.h use
for DT_RTC_0_NAME with DT_INST_0_NXP_KINETIS_RTC_LABEL to be
consistent. Also, remove the aliases that had been used for this
driver in various nxp_k*.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines and remove Kconfig per instance
enablement in favor of DT_INST_ define existing. Also, remove the
aliases that had been used for this driver in nxp_rt.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert pms7003 sensor driver to utilize device tree.
DTS would look something like the following for the pms7003:
uart {
pms7003: pms7003 {
status = "okay";
compatible = "plantower,pms7003";
label = "pms7003";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ak8975 sensor driver to utilize device tree.
This also supports the ak8975 embedded in a invensense MPU9150. In such
a case the device tree node should look something like, where the ak8975
is a child of the mpu9150.
mpu9150@68 {
compatible = "invensense,mpu9150";
reg = <0x68>;
label = "mpu9150";
#address-cells = <1>;
#size-cells = <0>;
ak8975@c {
compatible = "asahi-kasei,ak8975";
reg = <0xc>;
label = "ak8975";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32g0 SoC. Enable the independent watchdog
for the stm32g0 series for use with this driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds Device-Tree instances of the Flash controller
to the SAM3X, SAM4E and SAM4S series. The Flash-Controller
is used to get the unique device identifier.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
On stm32f302/3 series, USB and CAN_1 share same IRQ lines.
To use USB and CAN_1 together, USB IRQ could be remap to other
line numbers, on which there is no conflict.
Remap the USB IRQ lines by default:
-Assign remap number in matching dtsi files
-Perform remap before usb driver init
Additionally, fix compilation issue in usb driver.
Fixes#22343
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
List the details for each type in the order they appear in the summary
of all types. Add the missing 'path' value to the summary.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Fix the following device tree warnings:
unit-address and first reg (0x20000) don't match for iccm@0
unit-address and first reg (0x80010000) don't match for dccm@80000000
Since the em_starterkit_em7d_normal has a different base address for
iccm & dccm, and most of the em_starterkit variants have different sizes
for iccm & dccm. Just define the nodes in the specific
em_starterkit*.dts file and remove them from emsk.dtsi. This removes
the issue reported in the warning.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since there are times that we include a base .dtsi file and change the
reg address we tend to end up with warnings that the reg address and
unit-address don't match. To handle this introduce a simple DT_ADDR(x)
macro that will prepend '0x' to a 'unit-address' style address.
#define DCCM_ADDR 80000000 /* in unit-address format */
dccm0: dccm@DCCM_ADDR {
reg = <DT_ADDR(DCCM_ADDR) 0x1>;
...
};
This allows the dts file to override the value of DCCM_ADDR and than to
have the unit-address of the node and the reg address match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Create an SoC definition for the Audio DSP on Intel Apollolake
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a simple binding for the Cadence Tensilica Xtensa LX4
CPU. File originally from the LX6 binding.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Convert to support devicetree.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Mark all CC2520 GPIOs as required
in binding.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the lora/sx1276 driver to the new GPIO API, using configured
active level and the replacement interrupt and active-sensitive set
APIs.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Document and assign write-protect signal as active low, and use the
active-sensitive API to control it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
