A 1KHz counter is also available inside the NXP LPC RTC
block. Add a binding to support that counter.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This commit implements `otPlatResetToBootloader` in two ways:
- trigger reset to bootloader using boot mode retention API
- trigger reset to bootloader by triggering GPIO pin (applicable
for nRF52840 Dongle)
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
Use the common io-channel-cells name "input" instead of "channel" to make
this binding work with the various ADC DT macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This is a driver targetting the Bosch BMA 4-series accelerometers. It
has been specifically developed for the BMA422 but should be compatible
with others in that line, excepting the BMA400. Supports key attributes
and async RTIO one-shot operation. I2C operation is supported, with
stubs for a SPI implementation provided for future improvement.
Signed-off-by: Tristan Honscheid <honscheid@google.com>
In preparation for supporting all synchronization modes, this
commit introduces the rx_sync_mode/tx_sync_mode DTS properties.
Using these, the user will be able to specify which synchronization
mode the SAI should use.
At the moment, the driver does nothing with the values from
said properties but still checks if their values are sane
(i.e: it checks if the directions are both in SYNC mode which
is forbidden). By default, if "rx_sync_mode" or "tx_sync_mode"
is not specified, the direction will be set to ASYNC mode.
As such, below one may find a couple of valid examples
depicting this idea:
tx_sync_mode = <0>;
rx_sync_mode = <0>;
is the same as not specifying any of the properties,
tx_sync_mode = <1>;
rx_sync_mode = <0>;
is the same as:
tx_sync_mode = <1>;
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add support for specifying the domain/kernel clock along with a common
clock divider for the STM32H7 CAN controller driver via devicetree.
Previously, the driver only supported using the PLL1_Q clock for
domain/kernel clock, but now the driver defaults to the HSE clock, which is
the chip default. Update existing boards to continue to use the PLL1_Q
clock.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Some MCU have limitations with GPIO interrupts. Add a polling mode to
the gpio-keys driver to support those cases.
This required a bit of a refactoring of the driver data structure to add
a instance wide data, and move the pin specific pointer in the config
structure.
For polling, reuse the button 0 delayed work so we minimize the resource
waste, the two work handler functions are only referenced when used so
at least those are discarded automatically if no instance needs them.
Fix a bug in the PM structure instantiation as well.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add an input driver to read data from an analog device, such as a
thumbstick, connected to an ADC channel, and report it as an input
device.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add driver that based on RPI-PICO's PIO feature for ws2812.
This driver can handle WS2812 or compatible LED strips.
The single PIO node can handle up to 4 strips.
Any pins that can be configured for PIO can be used for strips.
I verified the samples/driver/led_ws2812 sample
working with WS2812(144 pcs) led strip using following patches.
- samples/drivers/led_ws2812/boards/rpi_pico.overlay
```
/ {
aliases {
led-strip = &ws2812;
};
};
&pinctrl {
ws2812_pio0_default: ws2812_pio0_default {
ws2812 {
pinmux = <PIO0_P21>;
};
};
};
&pio0 {
status = "okay";
pio-ws2812 {
compatible = "worldsemi,ws2812-rpi_pico-pio";
status = "okay";
pinctrl-0 = <&ws2812_pio0_default>;
pinctrl-names = "default";
bit-waveform = <3>, <3>, <4>;
ws2812: ws2812 {
status = "okay";
output-pin = <21>;
chain-length = <144>;
color-mapping = <LED_COLOR_ID_GREEN
LED_COLOR_ID_RED
LED_COLOR_ID_BLUE>;
reset-delay = <280>;
frequency = <800000>;
};
};
};
```
- samples/drivers/led_ws2812/boards/rpi_pico.conf
```
CONFIG_WS2812_STRIP_RPI_PICO_PIO=y
```
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Switch to using named IRQs as index-based access makes no guarantees about
devicetree interrupt order.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch to using named IRQs as index-based access makes no guarantees about
devicetree interrupt order.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Consistently use "int0" and "int1" as interrupt names for CAN controllers
based on the Bosch M_CAN IP core. This aligns with the upstream Linux
bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use the common io-channel-cells name "input" instead of "positive" and
"negative" to make this binding work with the various ADC DT macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This is in preparation for xmc4xxx mdio/ethernet patch set. In the
ethernet drivers, the DMA memory (including descriptor and buffers)
must live in dsram1 or dsram2.
Currently, in xmc47_relax_kit the RAM is the psram1 region meaning
that DMA transfers will not work. Switch to using dsram regions instead.
Also, merge dsram1 and dsram2 into a single region since they are
contiguous.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
S32K1xx devices have a maximum of 3 FlexCAN peripherals. Each part may
define a different maximum number of instances and message buffers,
hence the interrupt lines are defined in the part specific dts.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The zephyr-gpio w1 driver introduced in this commit implements
all routines for the w1 api on top of the zephyr gpio driver.
W1 bit read, write, and reset operations are executed by
bit-banging the selected gpio.
Signed-off-by: Hudson C. Dalpra <hudson@bduncanltd.com>
Some STM32F4xx chips have an R division factor in PLL. Add possibility
to configure that.
Even though the output from the R division is not used, it can be
increased to reduce power consumption.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Added GPIOTE0, GPIOTE1 instances for legacy devices,
GPIOTE20, GPIOTE30 for Moonlight and GPIOTE130,
GPIOTE131 instances for Haltium.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
The sci devices described in the device tree source for RA MCUs are
incorrectly specified as being UARTs when they should be SCIs (serial
communication interfaces) which can not only operate as UARTs but also
as I2C, SPI etc.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
This commit modifies the I2S driver to work for STM32H7
family of MCU's. Currently only TX is working.
Tested on nucleo_stm32h743zi. Requires dma1 & dmamux1 to be enabled.
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
Devices like the ATSAM series chips have retained registers
which are used to store memory. The memory is accessed just
like RAM, but since they are registers, their size and
address is used directly.
This commit adds a near complete copy of the generic retained
ram driver and bindings file, adding the reg property to
the bindings file, and updating the init macro in the driver
to use the reg address and size.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Rename old rpl_crb to rpl_s_crb, which is needed for adding other
Raptor Lake boards. Main changes should be in the board device tree
configuration raptor_lake_p vs raptor_lake_s.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add SOC definition for MK22F12 series, larger LQFP-144 K22 series
parts that feature additional peripheral instances.
Additionally, these parts differ from the standard MK22 in the following
ways:
- SYSMPU peripheral is present, so an MPU definition is required
- No external oscillator divider is present
This commit also updates the NXP HAL to include pin control files for
these SOCs.
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
Declare the SRAM0 region as memory-region
for the stm32f745 serie. Will be included for the stm32f746
for the stm32f765 serie. Will be included for the stm32f767
for the stm32f722 serie. Will be included for the stm32f723
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit updates the Ambiq Apollo4x series soc clock frequency
of defined instances to align with context of these dts files.
Signed-off-by: Aaron Ye <aye@ambiq.com>
