Add a GPIO nexus binding for Pmod interface connectors.
This commit also includes a header file with macros
that map signal names in the Pmod specification to
the corresponding indices in the GPIO nexus, meant for
use in devicetree files.
Signed-off-by: Alexander Mihajlovic <alexander@eub.se>
Add an input device to take input key events as an input and generates
short press or long press devices as output.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The number of available EasyDMA MAXCNT bits is now defined per-instance
in Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Change device tree VW routing to a form allowing overrides.
Add two new DT optional properties for specifying the reset
source and reset value of each virtual wire. Only virtual
wires that are enabled using the status property are modified.
NOTE: eSPI virtual wires are controlled in groups of 4 by
hardware. The optional reset signal source properties applies
to all four virtual wires in the group. If this field is
changed from the hardware default, it should be changed for
only one virtual wire in the group. If the property exists
in more than one wire in the group it must be set to the
same value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Modify Mircrochip MEC172x eSPI driver to get eSPI virtual wire
hardware routing from device tree.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The clock control driver requires three pieces of information:
PCR register index, bit position, and clock domain. Clock domain
was missing from DT information and MCHP macros.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Deleted adc_mchp_xec.c and microchip,xec-adc.yaml file.
DTSI, yaml, CMakeLists.txt and Kconfig.xec files are
updated for compatible.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Updated the "adc_mchp_xec_v2.c" adc driver to support both MEC172x and
MEC15xx SOC.
ADC smapling clock configuration updated using DTS.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Start using zephyr power management in cavs platform in a similar way
that is already done in ace. This commit only addresses the power off/on
sequence. Runtime power management is not implemented.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
The regulator driver has a configured min/max range that is used
to limit set values, and to initialise the regulator.
A new init value has been added, so that the startup voltage can
be higher than the lowest permitted value.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Added initial version of Infineon cyw43xxx BT (
H4 HCI extension drivers/bluetooth/hci/CMakeLists.txt)
Add initial version of binding file for Infineon CYW43xx BT
HCI extension driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
This adds a basic Intel TCO watchdog driver. The driver doesn't support
windowed timeouts (a non-zero window.min value) or callbacks. The driver
currently assumes TCO version 6, which can be found e.g. on Elkhart Lake
and Raptor Lake platforms. The driver also expects the TCOBA base
address to be specified through DTS, rather than doing runtime lookup
(using e.g. ACPI or PCIe).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remedial rework to handle the enabling of the I2S master clock
output based on the presence of an introduced DT property.
For details see issue/54841.
Signed-off-by: Raul Pando <raul.pando@bytegrity.co.uk>
This update devicetree entries and Kconfig definition to allow use of
reset cause on all SAM series.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add initial version of clock control for Atmel SAM SoC series. This add
support to Power Management which allows control peripherals clock.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
