- To link image loadable by MCUboot, zephyr,code-partition
must be set in the DTS.
- Move partition definitions from SoC DTS to the board DTS.
- Remove scratch partition since MCUboot does not recommend to use it.
- Increase bootloader partitions to 48K to fit recent MCUboot.
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The newly added "power-amplifier-output" property for STM32WL SubGHz
radio nodes is mandatory.
Add the property to all affected modules and boards with the
appropriate value for the factory-default hardware configuration.
Add the "rfo-XX-max-power" properties to all affected modules and
boards with the appropriate value for the hardware configuration.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Add STM32WL-specific sx126x_set_tx_params function based on the
STM32CubeWL modifications to LoRaMac-node.
Add the "power-amplifier-output" DT property to
"st,stm32wl-subghz-radio" for selecting between the RFO_LP and RFO_HP
output configurations provided by the above mentioned function.
Add the "rfo-lp-max-power" and "rfo-hp-max-power" DT properties for
defining the maximum design power of the respective outputs' matching
networks.
closes#48511
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Adds a retention system which builds on top of retained_mem
drivers to allow partitioning of areas and data integrity with
magic header prefixes and checksum of stored data.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds address cells of size 1 and size cells of size 1 to GPREGRET
instances for Nordic devices.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This commit adds support for the `drivers.adc` test by adding an overlay
for the `efr32bg22_brd4184a` board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
EFR32MG24 uses the Secure Element's mailbox for entropy gathering
purposes. Reflect that in the device tree structure.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
- Add Gecko BURTC sys_clock driver to handle wake up from EM2,3 states
- Remove custom PM policy and dependency on HAL sl_power_manager service
- EM1 supported in all configurations
- EM2,3 supported only if SysTick is replaced by BURTC
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The efr32bg22-pinctrl.dtsi file was shared between bg22 and bg27 files.
It's better to name it efr32bg2x-pinctrl.dtsi.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
This commit splits device tree into more logical structure. Peripherals
which are on a board are in board dts files, while those which are parts of
a SoC are in SoC dtsi files.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
The general structure of efr32b27_sltb010a board is shared by more than one
board. This commit intrduces changes to the organization of board files,
which aim to take that into account.
Signed-off-by: Krzysztof Boronski <kboronski@antmicro.com>
This commit makes the alarms-count dts property of the
rtc-device.yaml optional, setting the default to 0.
This simplifies the dts rtc dts node by not requiring
the property to be set to 0 if it is not supported.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
- Add initial version of Infineon CAT1 i2c driver.
- Add initial version of binding file for Infineon
CAT1 I2C driver
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
This adds the SPI driver for the Renesas SmartBond(tm) DA1469x MCU family.
The driver only supports controller mode. All four SPI modes are supported.
Note that the lowest supported speed is 2285714Hz.
Requesting speeds higher than 16MHz, will result in a 16MHz SCLK.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Move the devicetree bindings for Analog-to-Digital Converters (ADCs)
from dts/bindings/iio/adc to dts/bindings/adc as Zephyr does not have
an IIO layer.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
1. Increase sram to 256KB.
A block sram of SCAR0~15 is 4KB.
A block sram of SCAR16~19 is 16KB.
A block sram of SCAR20~23 is 32KB.
2. Removed the register of RVILMCR which has no effect.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The alternate pins of UART2 have been remapped, and the remapped
alternate pins must be added to the pinctrl map.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add the pinctrl node that has been remapped in the chip of it82xx2.
And modify kscan's pinctrl for the it82xx2.
And swap I2C default pins.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
On iMX.RT devices, the number of GPIO pins exceeds the maximum of
64 that the PINT interrupt controller can support. Therefore, two
interrupt lines are now shared between the GPIO modules.
This patch allows the user to set the interrupt source for a GPIO
peripheral. For most LPC devices, this will always be the PINT. For some
RT devices, the PINT cannot use pins on GPIO modules other than 0 and 1
as input, and thus the INTA and INTB sources should be used.
Since Zephyr does not support sharing these interrupt between all GPIO
controllers, the user must configure a subset of all GPIO controllers to
use the shared module interrupts. An example of how to do so is provided
for the RT595 EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce PINT driver, for NXP pin interrupt and pattern match engine.
The driver currently supports only the pin interrupt feature of the
PINT.
Add DTS entires for the PINT on LPC and RT devices that support this
peripheral, and remove the interrupt defintions that are PINT specific
from the GPIO module on these devices.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This patch adds HDA to device tree for LNL platforms.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The I2CLCTL_MLCS setting was recently added to MTL
platform. LNL has these registers in separate space, therefore
new field is added to intel,ssp-dai.yaml and appropraite definitions
to LNL device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Repleace usage of shim2 device tree field with hdamlssp.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In current implementation the HDAMLI2SL register is represented by
shim2 field in common SSP device tree file. This could be misleading
since the filed is is different location to I2S IP.
Adding separate device for this register following DMIC case.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
