Update our vendor-prefixes.txt file to match the data in upstream
Linux's vendor-prefixes.yaml file as of Linux commit
8ac91e6c6033ebc12c5c1e4aa171b81a662bd70f.
(We can't easily switch to using the Linux YAML file directly because
our documentation tooling depends on this plain text format.)
The changes were done using a script and then cleaned up by hand in
order to not throw away any Zephyr-only prefixes, and to manually
override Linux in some cases.
List of Zephyr-only prefixes, all of which were kept:
asmedia
cadence
gaisler
lairdconnect
ovti
openisa
particle
quicklogic
ruuvi
segger
vnd
weact
zephyr
Other things to note:
- keep Espressif as 'espressif', overriding Linux's 'esp'
- 'gw' is deprecated in Linux and is unused here; just remove it
- ROCKTECH DISPLAYS LIMITED SHOULD HAVE BEEN ALL CAPS;
HOW COULD WE POSSIBLY HAVE MISSED THIS BEFORE?
- Did not include '70mai' from upstream, as that violates the legal
compatible regexp
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
based on uart rom functions, also enable console driver
on top if this driver enabling logging
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
The booter (bootloader) behavior may be different in different NPCX
chip series. One example is that the booter sets host interface type in
NPCX7 series but leave the firmware to set it in NPCX9 series.
This commit adds a new DT node to record variants in its properties.
NPCX drivers can understand if they need to configure the related
setting by checking the node's properties.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
dtc v1.6.1 produces an error without specifying #address-cells
on an interrupt-controller node.
Fixes#36495
Signed-off-by: Eric Johnson <eric@liveathos.com>
Add watchdog support to the mimxrt685 platform.
The mimxrt685 platform is excluded from the watchdog
test case because the test case uses variables in the
noinit section that need to be retained through a reset
but the rt685 does not retain this memory through a
reset.
Signed-off-by: David Leach <david.leach@nxp.com>
The Texas Instruments TCA9538 is an 8 pin GPIO port expander.
It operates on an I2C bus with 2 configurable address pins. The
device has an interrupt output pin that is asserted when any pin
configured as an input changes state.
Added under the PCA953X name to allow other similar parts to
use the same driver.
Signed-off-by: Kieran Mackey <kieran.mackey@lairdconnect.com>
Microchip MCP7940N is a Real-Time Clock/Calendar. It operates on a I2C
bus. It can be used to set a calendar time and has two alarm channels.
When an alarm is asserted the state of the MPF pin of the MCP7940N will
change (depending on gpio active high/active low setting) to trigger an
interrupt.
Signed-off-by: Kieran Mackey <kieran.mackey@lairdconnect.com>
Add Atmel sam0 sercom[uart] pinctrl bindings and implements pinctrl at
driver level. It changes all sam0 boards to use new feature and remove
pinmux driver dependency for sercom[uart]. The samples that require a
binding were update to keep consistency and avoid errors.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Busy simulator is using counter device and entropy device to
generate random cpu load. Counter device cofiguration can be
used to set cpu load interrupt priority and optional pin that
can be set during the load.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add initial basic description for Cortex-M33 based
stm32u5 soc series.
This encompass description for base nodes, such as:
- cpu
- flash
- clocks
- sram
Additionally, provide description for variant stm32u575Xi.
Related to clocks nodes, added bindings for stm32u5 specific
rcc node as well as msi and pll clocks.
Header file stm32_clock_control.h was also updated to support
these new bindings.
Note that for compatibility with existing definitions, clock
node describing main pll clock, known as "PLL1", was given two
labels: "pll" and "pll1".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The type of DMA for the stm32f0 devices was wrong
Its DMA is of type V2bis where the peripheral request is fixed.
The corresponding DMA cell has 2 elements.
The stm32f091 has two DMA instances.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add a shim that allows using the nrfx I2S driver via the Zephyr API.
Add also missing devicetree nodes representing the I2S peripherals
in the nRF52 Series SoCs.
Extend the "nordic,nrf-i2s" binding with a new property that allows
specifying the clock source to be used by the I2S peripheral (so that
it is possible to use HFXO for better accurracy of the peripheral clock
or, in the nRF53 Series SoCs, to use the dedicated audio oscillator).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Create version 2 of the MEC GPIO driver to support MEC172x to not
interfere with MEC152x. When the MEC172x ECIA interrupt aggregator
driver is ready, this driver will use ECIA for registering GPIO
interrupt callbacks instead of maintaining its own interrupt table.
Add V2 DT binding.
Add the Kconfig configuration settings for the MEC172x GPIO
V2 driver at the SoC and board level.
Add port id to DT allowing use of DT FOR EACH macro in the driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This driver supports the TI INA230 and INA231 Bidirectional Current
and Power Monitors. The devices work on the I2C interface and are
created from DT nodes with a compatible property matching "ti,ina23x".
The following datasheets were referenced while developing the driver:
https://www.ti.com/product/INA230https://www.ti.com/product/INA231
Twister passed:
twister -T tests/drivers/build_all/sensor/
Testing was performed on the stm32g071b_disco board with the following:
Load: ~170 ohms
Voltage: 5V
Measured Values:
Voltage: 5.1 V
Current: 0.032 A
Power: 0.157 W
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
This CL moves the phandles which don't contain 'reg' prop. from 'soc' to
'soc-if' node since they are the interface phandles only. It also
prevents "missing or empty reg/ranges property" warning messages.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Update Microchip XEC RTOS timer driver adding MEC172x support and
using more device tree properities in the driver. We must also update
the XEC counter driver to use the new GIRQ DT properties.
Add new properties to RTOS timer and RTC timer YAML. These two timers
are linked due to option using a high speed timer for kernel busy wait.
Add Kconfig logic for XEC RTOS timer to MEC172x SoC.
Enable the Microchip XEC RTOS timer in the MEC172x evaluation board.
Add device tree nodes for most peripeherals.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
In the eeprom read operation, when rambuf was available
mutex was not unlocked after the read. Consequence of that is
that device was blocked after that read for incoming operations.
This commit fixes the issue
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add driver implementation and header files for a MEC172x
aggregated interrupt driver. Enable the parent(ECIA) node
to have the driver initialize interrupt hardware for use.
Enable child nodes for those GIRQs used for aggregation.
Refer to chip documention for the list of GIRQs restricted
to aggregation and those which support direct mode.
Add chip level device tree node for MEC172x EC interrupt
aggregator parent and GIRQ children. Each child node contains
a list of sources representing the source bit position in the
GIRQ registers.
Add DT bindings for ECIA and GIRQ nodes.
Add build file(s) and configuration items for the MEC172x ECIA
aggregated interrupt driver. Add and enable the MEC172x interrupt
driver on the MEC172x evaluation board(EVB). Enable parent node to
initialize ECIA hardware. Child nodes are left disabled until a
future driver needs them.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add basic counter driver based on Timer Counter (TC) module for Atmel
SAM family.
Remarks:
- The driver is not thread safe.
- The driver does not implement guard periods.
- The driver does not guarantee that short relative alarm will trigger
the interrupt immediately and not after the full cycle / counter
overflow.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds dt definitions for the hw aes accelerator
on stm32g0 Series.
The accelertor is available on the following socs:
stm32g041, stm32g061, stm32g081, and stm32g0c1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds a dt node for the hw aes accelerator of the
stm32l5 series.
The stm32l562Xe.dtsi file now includes the newly created
stm32l562Xe.dtsi with the additional aes definitions instead of the
stm32l552Xe.dtsi file.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds bindings for the STM32 AES accelerator.
Common properties of st,stm32-cryp are moved into
st,stm32-crypto-common.yaml.
The accelerator supports ECB, CBC, CTR, GCM, GMAC, and CCM
chaining modes.
128 bit bit data blocks with cipher key lengths of 128 and 256 bit are
supported.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Add support for power management and the shutdown mode for bq274xx fuel
gauge sensor. This now allows boards that have any kind of low power
mode to turn on or off the sensor.
Tested on a Company's custom board with bq27421 sensor on it.
Signed-off-by: Luka Lopotar <luka.lopotar@greyp.com>
Each stm32 dma can be of V1 or V2 or V2bis type. Each type
has a dma-cell with specific nb of element. The feature and slot
properties are not required depending on the stm32 family.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This will define a new bindings for any stm32 dma feature
Depending on the soc family, the DMA is of V1 or V2 or Vbis type
And give a factored definition for feature
The difference is on the dma-cell structure.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Implement a clock control driver for Microchip MEC172x handling
configuring the 32 KHz input sources for the PLL and peripheral-32k
clock domains. MEC172x differs from MEC152x. MEC152x had one 32K source
for both PLL and peripherals. MEC172x allows the two domains to use
independent 32 KHz sources. Device tree updated to provide addresses
of hardware used by the driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This adds the dts to PASS the tests/drivers/dac/dac_loopback
on the nucleo_f429zi board, when PA0 and PA4 are connected.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds a driver implementation for the LM75 I2C temperature
sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@leica-geosystems.com>
reuse the lpc's lpadc driver for rt1170, modify the dts and add
some macro to shield some code of LPC series. Also add the
board support inside the tests/drivers/adc/adc_api/src/test_adc.c,
and a dts node:zephyr,user inside
samples/drivers/adc/boards/mimxrt1170_evk_cm7.overlay
Signed-off-by: Crist Xu <crist.xu@nxp.com>
