The macro defining the device_pm_ops structs is located inside an
ifdef for CONFIG_UART_QMSI_0, so when the UART_0 is disabled at build
time, but UART_1 is still used, it references a struct not defined.
Fix it by placing the DEFINE_DEVICE_PM_OPS line outside the ifdef block.
Change-Id: I7dafda162741201ee47b5b480c07ec8c1f373d64
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The slip driver revert (3e63a74) was incomplete, missing the Kconfig and
Makefile changes, causing 'make clean' to fail.
Change-Id: I9d944148e6be3756b62d2371a5ab5528365e1ec1
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
The idle status check before a i2c transfer is not a reliable
way to check whether i2c master is ready to transfer data. If
the data transfer for the previous API call is done, but, a
stop condition is not sent by the previous API, the i2c master
is not idle, but, it can start new data transfer.
Change-Id: I93dbf46cef6272f3da69a0d67fb737c9b480791f
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
We have already done this on x86 and ARM. The policy is as follows:
* IRQ priority levels starting at 0 all have the same semantics and
do not have special properties. The priority level is either ignored
on arches which do not support programmable priority levels, or lower
priority levels take precedence over higher ones.
* Special-case priorty levels are specified via flags, in which case
the supplied priority level is ignored.
Issue: ZEP-60
Change-Id: Ic603f49299ee1426fb9350ca29d0b8ef96a1d53a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This will guard the driver API to be safe for concurrent
invocation from fibers or tasks.
The machanism is by default disabled. To enable it, the
following flag needs to be defined:
CONFIG_GPIO_QMSI_API_REENTRANCY
Jira: ZEP-441
Change-Id: Ia3ee738aff2f8e70e4f9a7ec76346138ff6f5031
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This will allow the driver API to be safe for concurrent invocation
from fibers and task.
The machanism is by default disabled. To enable it, the following
flag needs to be defined:
CONFIG_GPIO_QMSI_SS_API_REENTRANCY
Jira: ZEP-411
Change-Id: I5b738532f2eefec6d5d78ab6a668790dfe9faaff
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
At the moment firmware reads everything we send to it over UART and
when an application tries to send too much notifications we are stuck.
The proper approach would be forcing firmware to read from UART only
when there is available memory. In this case we would block on UART
FIFO and everything handles gracefully.
This workaround mimics solution used by firmware project by allowing
to send next notification only after previous was sent correctly.
Change-Id: I56dd5abc4d13735d285415da04db75e7bb8bc459
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Depending on advertising options this can be non-connectable address.
NFC pairing application document also allows broadcaster/observer
roles.
Change-Id: I9b104ac8fb9752a083a7a31fc20598c66f23f608
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Follow up to TSC decission for further discussion in the networking
WIG.
Change-Id: I148b484dfe308661573e47ed3e60cceed673bddf
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This adds some basic suspend/resume support in the uart_qmsi
driver. This is part of a change to enable device suspend/resume
and deep sleep support in sample PM application.
Jira: ZEP-512
Change-Id: I38cfbfb352d0027b7beaadebedbc10002dade50a
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
This adds some basic suspend/resume support in the rtc qmsi
driver. This is part of a change to enable device suspend/resume
and Deep Sleep support in sample application.
Jira: ZEP-512
Change-Id: I79ccfb56de5b3cbfb5bc91e9cacca68554aa46ee
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
This is part of a change to enable device suspend/resume and
Deep Sleep support in applications. Adds suspend/resume handling
in loapic timer.
Jira: ZEP-512
Change-Id: I9da2c8419bd9109fb71ef5a6caf736de7c7de9e1
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
This will guard critical regions in the driver API so that the API
operation called from one thread (task or fiber) can complete
without the context being over-written by any simultaneous call
of the API from other thread (task or fiber).
The locking mechanism is by default disabled in the build. To enable it,
the following flag needs to be defined:
CONFIG_AON_API_REENTRANCY
Jira: ZEP-424
Change-Id: I1b0eae70a4ab97229931033153662874d7c4a68e
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This allows to query information needed for Out Of Band pairing
or connection creation. Currently supports only BT addresses.
Change-Id: I60bf9344baee552e7743fa8fc1b3cfb3a4765334
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This lets the callback take advantage of the powerful net_buf API for
parsing the advertising data content.
Change-Id: Id65e6e83efd60c0f36c47bc5446a2e8ec2833d7c
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This makes bt_gatt_write consistent with the rest of the API where the
parameters are passed back to its callback.
Change-Id: Ie94208aa661d3620d0cbc5be4a4fb5b3c3ef061c
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fixes SEC/AUT/BV-11 PTS test case at least in GUI mode.
Change-Id: I60e7013f1c66027dabc1b94df87f2da991a5718c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
QMSI provides more than just peripheral drivers, and it may be used
from the SOC or by applications that need finer grained control of the
platform.
This also makes the QMSI HAL consistent with the others.
Change-Id: I27490c98ccf1c1afcc090ce1e65f0e066eddc777
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Correct that handle is attribute one, print flag to notice cancel
prepared write requests.
Change-Id: I46d747f0466a44460e92fcbaef4e436066c09f4a
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The latest NBLE firmware includes a new version
exchange mechanism that is independent from the
RPC function definition. It also allows using
firmwares that are automatically generated by
the official builders without needing a local
build.
The upgrade of the softdevice fixes several
issues in PTS tests. The major change in
term of API introduced by this upgrade is that
upon write requests, the offset and data of the
write request must be sent back to the softdevice.
Change-Id: Ie574047a09a4e6fdcbf775bc98d8a61f981cee0c
Signed-off-by: Louis Caron <louis.caron@intel.com>
The comments state that higher-numbered vectors have priority,
but the function was doing the opposite. The code now agrees
with the comments.
Change-Id: I1a689fc22c8355458bdd734d95ff637da0655533
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Created menu for Ethernet driver and moved driver + debugging setting
under it. Changed prompt from "Grove log level" to more describing and
fixed typos.
Change-Id: If2f79fee1a002a42e89e2493a2294332abec05ee
Signed-off-by: Jani Pajarinen <jani.pajarinen@intel.com>
As there is a L2 in the middle, there is no need for a net_if to provide
such information.
Change-Id: I58a35d4d124cd8a67026f32e71713ef06f43b7c5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Net core then does not know anything about l2 related logic.
For instance ARP is used in ethernet l2 API and nowhere else.
This will be helpful when adding different technologies altogether.
Currently, only SLIP driver is enabled to use relevant l2 layer.
Change-Id: I03c93326321028d04222733ca4083e3c6b785202
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2 warnings happens when CONFIG_SLIP_DEBUG is set, thus fixing it.
Change-Id: I032d7481942e86911764da35cdd6f7b8e05cdeaa
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If CONFIG_SLIP_TAP is defined, then ethernet link layer header is
used before the packet.
Change-Id: I3d266017f85683999d3c67de49b75b60686d7ba7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use IOAPIC_EDGE instead of IOAPIC_LEVEL to fix missing interrupts.
During tests it was found that using IOAPIC_LEVEL interrupts for UART at
some points are lost.
Proposed by Calando, Antoine <antoine.calando@intel.com>
Change-Id: I18b20217c4d73fdeaa424bf59d00f6be1ec6ef1b
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Renamed net_recv() to net_recv_data() so that the more generic
name can be used by applications. The net_recv_data() is only
meant to be used when L2 layer feeds data into L3 (IP) layer.
Change-Id: Iba155d51f81e3b99964fa916fe87a05a8bf8766a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Check if we have received IPv4 packet and call a handler
function to process it.
Change-Id: I9f9e5f0888d2c3b91401c98f4925647ddce09962
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The SLIP driver is using UART pipe driver to communicate with
host when Zephyr is running in Qemu. Currently this is only
used by networking sub-system when testing the networking
stack.
Change-Id: I432b4136670766a7fc190f146057924c266f9bea
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Debug macro definition at this file was repetitive and has been
superseded by new system logging API. Furthermore it was not being
used on this .c file.
JIRA: ZEP-311
Change-Id: Id5828d1144fa03cc24f100ae94ecc596502c1131
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Clock control drivers are now using new system log macros. also update
the Kconfig variable to be a level rather than a bool.
JIRA: ZEP-311
Change-Id: Ia64e79e4e083df580861f64c661f8dbaa8a3985d
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Protect FIFO writes against other USB register accesses.
According to "DesignWare Cores USB 1.1/2.0 Device Subsystem-AHB/VCI Databook":
"During FIFO access, the application must not access the UDC/Subsystem
registers or vendor registers (for ULPI mode). After starting to access a
FIFO, the application must complete the transaction before accessing the
register."
Change-Id: I2aed833acaa2970310b6fd48f41a95bee2182ec1
Signed-off-by: Adrian Bradianu <adrian.bradianu@windriver.com>
Designware, Amtel and Quark SE i2c drivers are now using new system
log macros. also update the Kconfig variable to be a level rather than
a bool.
JIRA: ZEP-311
Change-Id: Iac009b20fb74deb8ce72098378651bbec3b2ef17
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
This replaces the use of delayed fiber with delayed work which doesn't
require extra stacks.
Change-Id: I3db0c168baabea2503163e26020bf5e4971ce584
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Correct ADC resolution definition and default value in Kconfig.
QMSI uses different definition for sensor. But, Kconfig did not
reflect the difference.
Change-Id: I8e57aa5670bff0e5b29bf0772159834e4b902d88
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Use the function provided in misc/util.h to do the sample
conversion.
Change-Id: I21179982b6001bf79448e4eb289e9cffaf97f3fb
Signed-off-by: Mariusz Ryndzionek <mariusz.ryndzionek@firmwave.com>
This allow the PWM QMSI shim driver to implement the set duty cycle
API, and correct the behavior of Set Value
Jira: ZEP-69 ZEP-156 ZEP-158
Change-Id: I47744958fed889116fbb5024343ea00f76ed7706
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Fix a bug in i2c_qmsi_transfer function in the shim driver.
The function did not wait for the completion of a msg transfer
before starting another msg transfer. Similar issue exists in
the i2c sensor shim driver. It is also fixed.
Change-Id: I1f8ad2281fa185d85db25a4682ed596c02ea322e
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Revert patch fixing Bluetooth application with Debug enabled crashing.
This reverts commit 029d3beb57.
Change-Id: I0004dae656ca5a0b44da9f12542088d47c38b837
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
QMSI 1.1 Beta is available on Github:
https://github.com/01org/qmsi/releases/tag/v1.1.0-beta
Update the QMSI drop we maintain in Zephyr and
keep the modification to qm_soc_regs.h introduced on commit
6b88a6b945 "ext qmsi: Add USB base and interrupt defines" since
that patch hasn't made into the QMSI 1.1-Beta release in time.
Also, fix the build where needed:
- add hard dependency from qm_i2c to qm_dma
- fix spi_qmsi_ss.c due to new parameter naming
- fix adc_qmsi.c and adc_qmsi_ss.c due to a new parameter
Change-Id: I01388c787f5ee6ee97fece2e42b24a717522207f
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
SPI drivers for K64 is now using system log.
Change-Id: Ifd0d321e2ff84c581261b7cb3a7a4485afbd67f6
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
JIRA: ZEP-311
ADC driver is now using new system log macros, also update the Kconfig
variable to be a level rather than a bool.
JIRA: ZEP-311
Change-Id: Iac96c37989e44484808ded515397d457186240e0
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Fix bug that caused negative temperature values to be computed incorrectly.
The sign bit needs to be perserved, when extracting the data sample from
the TMP007_REG_TOBJ register.
Jira: ZEP-499
Change-Id: Idbebd48b3164d7d4883352ef7128ef73be70e1b2
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Add hyphens so that the .rst file is formatted properly
Change-Id: Ic798590d4a892f4f4d5312e86949db23a3b3abe0
Signed-off-by: Mariusz Ryndzionek <mariusz.ryndzionek@firmwave.com>
