Also, SPI 0 isn't specific to Intel, make it a generic message. This patch
only fixes the cosmetics w/o changing undering Kconfig option names.
Change-Id: Ia58f9537c594004a1b5fb8b4af21d7e8b729efb7
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Fix i2c failure seen on fast plus mode. With higher data
rate, signal ramp time becomes longer. The ramp time
required by the controller needs to be loosened.
Jira: ZEP-711
Change-Id: Icffa334ec3f059564e333d3b0759a11d1bebc5e4
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Defined in all SoCs, but never referenced anywhere. That definition has
been replaced by CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC.
Change-Id: I1801f72a03925717ded6fbfdef22b1993f843461
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Correct the argument definition inconsistency for the set
value API. To be consistent with other pwm sub drivers, the
on and off arguments for the set value api are re-defined.
On: how far (number of timer count) from the beginning of a PWM
cycle the PWM pin will be asserted.
Off:how far (number of timer count) from the beginning of a PWM
cycle the PWM pin will be de-asserted.
Jira: ZEP-642
Change-Id: I7b39f98f1935fc3499fb36dd813abed62b86c1e7
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This will lead to conflicts and warning coming from Kconfig, so just
whitelist the board in the samples where this hardware is supported
Jira: ZEP-739
Change-Id: I4a2f3bdcfdb44fc75df0e272c237789ee16e0de1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Kconfig allows selecting NETWORKING_WITH_15_4_TI_CC2520 even if the
current board doesn't support it, and also selects it by default. This
breaks building the 15.4 sample with qemu_x86. Add a config option for
having CC2520 support and enable the choise only if it is available.
In addition, remove unused function from iee802154 code, as it now
fails the tests.
Jira: ZEP-697
Change-Id: Ib082f82acdd0f86d3306bbd3bb827f61b0fd0be1
Signed-off-by: Jaakko Hannikainen <jaakko.hannikainen@intel.com>
Completing the terminology change started with change 4008
by updating the Kconfig files processed to produce the
online documentation, plus header files processed by
doxygen. References to 'platform' are change to 'board'
Change-Id: Id0ed3dc1439a0ea0a4bd19d4904889cf79bec33e
Jira: ZEP-534
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
A previous re-work of IRQ priorities was led astray by an incorrect
comment. Priority level 1 is not a non-maskable interrupt priority.
In addition, zero latency IRQs are not implemented on ARC.
Timer driver now doesn't specify IRQ_ZERO_LATENCY (as that wouldn't be
correct) and its IRQ priority is now tunable in Kconfig. The default is 0.
IPM driver on both ARC and x86 side were being configured with hard-coded
priority of 2, which wasn't valid for ARC and caused an assertion failure.
The priority level is now tunable with Kconfig and defaults to 1 for ARC.
Issue: ZEP-693
Change-Id: If76dbfee214be7630d787be0bce4549a1ecbcb5b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Per spec document, RXEN bit corresponds to bit 2
of the ECON1 register instead of bit 1.
Change-Id: I1bbfd048be248575a558679985ba9daadc43df0e
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
The rx fiber call contiki IP stack functions to register
received frames. This interaction requires more stack memory
in the rx fiber stack to avoid memory corruption.
Change-Id: I106339e7dd1ca9282426adfb54590e34297755b3
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
SPI bus is a shared resource between tx and rx processes.
The access to it must be synchronized to allow a rx process to
happen even when a tx process is taking place.
ECON1 register must be saved by the rx process and recovered
at the end to ensure that the tx process will continue operating
in the same register bank.
Change-Id: Ie9358bf02bef8ddb5bdf76c8847e998a627e5395
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
Transmision status is polled. Remove rx interruption enabling and
clearance.
Change-Id: I2893f89533adef5f77c711a36b5c1bbe21c48a23
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
Even values in ERXRDPT register may corrupt the receive buffer.
Set ERXRDPT value one address behind the next value.
If it is zero, set the value to the reception buffer end address.
Change-Id: I7150e5190c5bfb7bfafbff598eea1c26959643d0
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
These console messages are for debugging and if sent too
rapidly, could be discarded. This was causing false positives on
test cases which rely on console output to determine success or
failure.
Issue: ZEP-704
Change-Id: I5a86c761311cde90f295cd2e65f2e70608f875fa
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The Receive Packet Pending Interrupt Flag (EIR.PKTIF) does not
reliably/accurately report the status of pending packets.
Reception fails intermittently. The EPKTCNT register is used instead.
Change-Id: I599c3b4df1b74d769dd7104e5c6e253d9cf63bd4
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
The (currently) unused ipm_device field wasn't initialized.
Issue: ZEP-704
Change-Id: Icbeb50031c52d2513a1417f83a844e25b43429a7
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fix i2c failure while multiple slaves are connected to the
same i2c interface. Higher load on the i2c bus makes i2c
signal less nice. The requirement for signal ramp up and
ramp down time needs to be loosened.
Jira: ZEP-646
Change-Id: If698d7ba741788857694f166ecc602c2a94cb12e
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The data sample registers are ordered as X, Z, Y (not X, Y, Z), so the
driver also needs to extract the sample components in this order.
Jira: ZEP-679
Change-Id: I317994bb545539b049e2ebf3d2af94e63c7d2511
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Correct an error in ADC Kconfig. The # in the beginning of
the code lines unintentionally commented out the "if" condition.
Jira: ZEP-645
Change-Id: Ieee1bdbf4865fc39aef9a0986036fd81a75e5b58
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
Adds the ENC28J60 Ethernet module driver.
Origin: Original
JIRA: ZEP-291
Change-Id: I2b5790ecb251f9059f172bcaafadef24bd27207a
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Fix several issues which are causing the BMI160 app hang.
For SPI duplex transfer, QMSI only supports equal length.
For SPI freq, divider is used. Actual freq is no longer used.
Jira: ZEP-461
Change-Id: I1a1bcc12c6514c3797686dfdad1ce1b852f7dc78
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
One remaining reference to uart_qmsi_pm_save_config
was missed by patch bc60506d3e.
This reference is removed.
This fixes the following error:
...
drivers/built-in.o: In function `uart_qmsi_line_ctrl_set':
/drivers/serial/uart_qmsi.c:439:
undefined reference to `uart_qmsi_pm_save_config'
collect2: error: ld returned 1 exit status
...
Change-Id: I1ceda0e152db5a1c7f70d67c04b931416687031a
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Implement saving and restoring context of the PWM controller when the
application goes to SYS_PM_DEEP_SLEEP. No action is taken for other
states at the moment.
This functionality is implemented in the shim driver first to enable
the feature, but will later be moved into QMSI.
Change-Id: I5784f6a2c63caaea5785ca5d92bb6cc3bc9fa4cc
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Removed dead code inside sensor_lsm6ds0.h. There is no kconfig option
CONFIG_LSM6DS0_I2C_ADDR_6A neither 6B.
Also the #define LSM6DS0_I2C_ADDR is not in use.
Change-Id: Ib5a7f40d0d61542ed81687227df3795ba52ec725
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
In order to restore uart context after entering
SYS_PM_DEEP_SLEEP, suspend and resume functions
are called.
The following parameters are restored:
- All registers for the UART device.
- UART clocks.
The FIFO control register cannot be read back and is
not stored in the device configuration.
The default parameters are applied for them.
The suspend/resume functionality is implemented in
the QMSI shim layer as a fast and temporary solution,
it will be removed and migrated to QMSI later.
Change-Id: I4be9246f6aa5a6e0d91df54c1c69574060136607
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
ieee802154 driver is now using new system log macros, update the
Kconfig variable to be a level rather than a bool and the .conf
files at samples.
JIRA: ZEP-311
Change-Id: I640e973d880c3a222cd7c13a72d35edf49ada3a8
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
DesignWare USB driver is now using new system log macros, updated
the Kconfig variable to be a level rather than a bool and the .conf
files at samples.
JIRA: ZEP-311
Change-Id: Ief46cadd954ca4b30a3a1cf2eba6e44ccbc9bc9f
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Freescale K64 PWM driver is now using new system log macros, updated
the Kconfig variable to be a level rather than a bool.
JIRA: ZEP-311
Change-Id: I80d01ba75e8b186ef32861b372af4e2d15dd4131
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Calls to flash write or erase operations can get preempted
in the middle of the API call if a concurrent call (from
other fiber or task) to the same API is made. The patch ensures
concurrent API calls from other fiber/task is put on hold until
the current operation is completed.
The mechanism is by default not activated. To enable
it, the following flag needs to be defined:
CONFIG_SOC_FLASH_QMSI_API_REENTRANCY
Jira: ZEP-414
Change-Id: I39429e40cb6ed446123dd1a1d7c7acc1b12417aa
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
pcal9535a driver is now using new system log macros and updated the
Kconfig variable to be a level rather than a bool.
JIRA: ZEP-311
Change-Id: Ic3d6c72630e66ac116c1e8954c32254677c51566
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
GPIO drivers are now using new system log macros also updated the
Kconfig variable to be a level rather than a bool.
JIRA: ZEP-311
Change-Id: I9a49626d816080cb8081c2dd445bae31f5dbf409
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Drivers that implement power management should use the preferred
device_pm_ops method instead.
Change-Id: I9ae06e26b77325265bbe46bdee82ba39dedb6b79
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Drivers that implement power management should use the preferred
device_pm_ops method instead.
Change-Id: I337722b1e06afe8508b5c84c00c3542571232e07
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The suspend and resume hooks in the spi_driver_api struct are relics
from before the current power management infrastructure was in place.
The correct way to implement this now is through the device_pm_ops
struct, by way of the DEFINE_DEVICE_PM_OPS and DEVICE_AND_API_INIT_PM
macros, which make the hooks available through a generic mechanism for
all devices, rather than using per-type APIs.
Since the existing spi_suspend() and spi_resume() functions don't check
if the driver_api hooks are NULL, there's now a place holder function
to prevent breaking functionality until the hooks are removed.
Change-Id: I48287c58e9a8649d3e1be7547e3d0d293c84327a
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The suspend and resume hooks in the spi_driver_api struct are relics
from before the current power management infrastructure was in place.
The correct way to implement this now is through the device_pm_ops
struct, by way of the DEFINE_DEVICE_PM_OPS and DEVICE_AND_API_INIT_PM
macros, which make the hooks available through a generic mechanism for
all devices, rather than using per-type APIs.
Since the existing spi_suspend() and spi_resume() functions don't check
if the driver_api hooks are NULL, there's now a place holder function
to prevent breaking functionality until the hooks are removed.
Change-Id: I6a3e3db370860ad46f428d287943b1ca58a80ae1
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Drivers that implement power management should use the preferred
device_pm_ops method instead.
Change-Id: Ice9e0469a1fcb50eb64dcb240dddea56755b6e84
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The suspend and resume hooks in the pwm_driver_api struct are relics
from before the current power management infrastructure was in place.
The correct way to implement this now is through the device_pm_ops
struct, by way of the DEFINE_DEVICE_PM_OPS and DEVICE_AND_API_INIT_PM
macros, which make the hooks available through a generic mechanism for
all devices, rather than using per-type APIs.
Since the existing pwm_suspend() and pwm_resume() functions don't check
if the driver_api hooks are NULL, there's now a place holder function
to prevent breaking functionality until the hooks are removed.
Change-Id: Ib6b03053b483f97a1f7441af5ba51503270b8674
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Added CONFIG_SYS_LOG_I2C_LEVEL define, so that DW I2C driver will
not print traces unless requested with CONFIG_SYS_LOG_I2C_LEVEL.
Currently it doesn't obey it, so DW I2C spams DBG traces when
logging is enabled.
Change-Id: I87dc1d922ba61d39f26945627602864c75d9bf33
Signed-off-by: Jani Pajarinen <jani.pajarinen@intel.com>
Fixed undefined CONFIG_ISL29035_LUX_RANGE_4 in #elif
Change-Id: I2a7a6e46ffa0236da126d4e2c321e59302e54527
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
Guard critical section of the driver API, so that multiple
simultaneous calls from tasks/fibers won't corrupt the driver
state.
The locking mechanism is by default disabled. To enable it,
the following flag needs to be defined:
CONFIG_PWM_QMSI_API_REENTRANCY
Jira: ZEP-430
Change-Id: Ia3eb2a962f4176a3ac94163b9843ab068abe4b4e
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
In order to restore GPIO context after entering
SYS_PM_DEEP_SLEEP, the suspend and resume
functions for GPIO and GPOIO_AON are called. The
following parameters are restored:
- All non-sticky RW registers for the GPIO device.
- The MASK register (interrupt routing register).
Note: No need to sve/resume AON_GPIO registers as
they all are sticky registers.
The suspend/resume functionality is implemented in
the QMSI shim layer as a fast and temporary solution,
it will be removed and migrated to QMSI later.
Change-Id: I68e25c9da4bb8ea65f312e3686d9ef090cb775ff
Signed-off-by: Dragan Cvetic <dragan.cvetic@intel.com>
