Add typecasting in dma QMSI shim to avoid compilation error.
The DMA API and QMSI have their own definitions for the
dma configuration parameters, such as handshake_interface,
handshake_polarity, source/destination_transfer_width,
channel_direction, and source/destination_burst_length.
When a API is called, the shim driver will assign values
for the above-mentioned parameters to the configuration
variable(based on QMSI's definiton) from the values in the
variable provided by the caller based on API's definition.
Even though all these parameters have similiar definition
and values in both the generic API and QMSI, QMSI uses
its own names which are different from those definied in
the generic API. Without typecasting, the parameter value
assignment will cause compilation error(even though error
only happens for some compiler).
Jira: ZEP-1031
Change-Id: I147c690799514bd611cd9f88316f44346e095359
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
As part of an effort to closely integrate with Zephyr OS,
removed the custom implementation of IRQ interfaces used
in controller code.
Jira: ZEP-841
Change-id: Ie427f45aeecad51053112371526cb7dc4817248f
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Code under SCHED_ADVANCED macro in ctrl.c is used to
disable advanced radio time space scheduling calculations
used for placing non-overlapping observer and master roles;
to populate connection parameter request/response PDU
fields, and autonomous generation of slave initiated
connection parameter requests.
This macro shall always be enabled for optimal and correct
operation of the controller, It shall only be disabled to
debug failures in other part of the controller, to rule out
this code's influence, if any, on the failure being
debugged.
Change-id: I04e5f837ef0a5658361bd3668f583f1e13504570
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Place __packed at the end of the structure definition in line
with the rest of the Zephyr codebase.
Jira: ZEP-732
Change-Id: I25aa731cbd188a6e23ca2035eb22fa919295bb25
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Leftover from previous commits, this macro is not used anymore in
the HCI implementation.
Change-Id: I376c92a6b68432d2ff818ea25e68f087131e8479
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the net_buf structure directly when populating incoming
ACL data or asynchronous events. This ensures that no additional
memcpy() operations are required and removes completely the
statically allocated buffers in hci.c.
Jira: ZEP-726
Change-Id: I6ac8bd0becb7037ce8ecfac109f44832d23fcfd2
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Preallocate a response event net_buf buffer before processing an
incoming command and provide it to hci.c so that it populates
the event directly, instead of using a temporary buffer than
must then be copied into the return net_buf.
This applies exclusively to Command Complete and Command
Status, since those are the only events that are sent in
direct respone to an incoming command.
Jira: ZEP-726
Change-Id: Ia3ea71ac497690af929c44308760f68491ea829e
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of copying the net_buf contents into a temporary
buffer byte-by-byte, the Controller HCI code now handles
incoming commands and ACL packets from the Host directly
in the net_buf containers, to avoid unnecessary memory
copying and to align with the rest of the Bluetooth stack.
Jira: ZEP-726
Change-Id: I9802607d84ee6206218b711e7e6e23dafb70581a
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As part of the effort to consolidate the BLE Controller's
HCI layer, the functions in hci_driver.c now use the "hci_driver_"
prefix when it is sensible to do so, and prefixes have been
removed altogether when they are not required.
Jira: ZEP-726
Change-Id: Icd3e56e0170f15636245ea12a389a5a9e86c166c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add PTB22, PTE26, and PTB21 to the frdm_k64f pinmux table, and helper
macros to board.h to map them to red, green, and blue LEDs respectively.
Change-Id: I257621467e71dfd9bdc5d97d6da444dfb5c58b2b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add PTC6 and PTA4 to the frdm_k64f pinmux table, and helper macros in
board.h to map them to SW2 and SW3 respectively.
Change-Id: Ia30df9015d6d3c09131b4fbb2f2009ee745f7268
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Statically compute the number of elements in the pinmux table rather
than keep a manual entry in step with the table.
Change-Id: I99634aa460a39bb8a9a10fe37d28aaae792aa641
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
MVIC does not have _REG_TIMER_CFG defined because it does
not have a timer config register. Add checks for MVIC at
places where it is used.
Jira: ZEP-1015
Change-Id: I59f5c43cc2d1b17cf9e88b940631c2542e9729ab
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Interrupt stubs now just push the ISR and parameter onto the stack
and jump to the common interrupt code, never to return.
Change-Id: I82543d8148b5c7dfe116c43f41791f852614bb28
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In some cases we can either assume they are already masked
at boot and save some cycles, or the IOAPIC has configuration
from a prior boot stage that needs to be preserved.
Change-Id: I0c71ff0f01a6ee13a3b9c9e239d5a933d6cb6542
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This reverts commit 581e15ced2.
The commit was marked RFC and should not have been merged yet.
Change-Id: Iafd3587f8840e64670c32fa5726ea20ac9c9962a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
This driver is functional, just. It is not in a fit state to be merged to master yet.
Origin: Original
Change-Id: Id29e756f33c6c0263926139188c49f9a9c3d5e09
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Updated CONFIG_SOC_QUARK_SE_SS to CONFIG_SOC_QUARK_SE_C1000_SS
Change-Id: I7dc02d91a4d739f6cd3f84001d1dd29759317163
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
No need to create new Kconfig that do exactly the same, just
reuse those from the main QMSI driver.
Change-Id: I965055f36845ac0464e4a383b0d05c3ae35c0015
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update the power sample and drivers with the new device driver power
management API using the existing logic
Jira: ZEP-954
Change-Id: Idd94232e458767635973e94e9fc673c01612c1e2
Signed-off-by: Amir Kaplan <amir.kaplan@intel.com>
Removed CONFIG_INT_LATENCY_BENCHMARK dead code.
CONFIG_INT_LATENCY_BENCHMARK depends on ARCH="x86", it will never
be true for ARM code.
Change-Id: Ia5779a69b1bf670ebb140c2923c9fe0af6b781d4
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
Removed unused workaround in loapic. There are no references
of usage.
Change-Id: I8700b4b7ce8efef5e7b95e6cdd2b201eae3f1f37
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
During USB device reset, the controller must have its device address
cleared (set to 0). This is not really taken into account by most host
side stacks, which is the reason why this bug didn't show up before.
It was found when we were trying to run the USB20CV [1] compliance test
suite on Windows.
Without this fix the device doesn't show up on the targets list, which
means device enumeration failed. With this patch in place the bug is
fixed and the device gets listed.
Tested with the CDC ACM sample application.
Jira: ZEP-950
[1] http://www.usb.org/developers/tools/usb20_tools/
Change-Id: I0b78f7ce043fa29dde0fb7f3b3aecee9844f4d11
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
The driver originally gets the full-duplex configuration
from the PHCON1 register and PDPXMD bit as stated by the
ENC298J60 specification document section 2.6 "LED Configuration".
This section trust the board to LEDB connection to signal the
full-duplex configuration.
This commit gets the full-duplex configuration from Kconfig
symbols to allow a proper functionality even when the board
is not connecting LEDB apropriately.
Change-Id: I803958409a611e23e2c3e03f40b412f1695947af
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
There is a tx semaphore that controls a single access to the
transmission service. The device is capable to manage a single
transmission call at a time. Multiple requests need to wait
for the resource to be free.
This commit adds the initial release to the tx semaphore.
Jira: ZEP-895
Change-Id: Ic9879cfd15bb1494644b2cf0f4565f7e6a2c1c22
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
ENCC28J60 specs section 6.5 "MAC Initialization settings"
state that MACON3(7:5) register configure automatic padding and CRC.
It also states that the configuration 111 and 011 both configure as
all short frames to be zero padded with a valid CRC appended.
Nevertheless, experimentally, there are ocassions when configuring as 111
frames does not have a CRC appended. This frames could be rejected
by the receiver if it is configured to do so.
This commit changes configuration from 111 to 011, which is not
presenting that behavior.
Jira: ZEP-842
Change-Id: I302bb99f7a1f23b298fe0db0245963b640644040
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
As part of the effort to consolidate the BLE Controller's
HCI layer, the following files have been renamed:
* hci.h -> hci_internal.h: contains the HCI API to be used
by the driver
* main.c -> hci_driver.c: Implement bt_driver and includes
initialization and glue code
Jira: ZEP-726
Change-Id: Ica8b3e114da42a766a1b14ce59558cacd899a1a7
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the sys_ macros from byteorder.h to access all HCI
structure members that are endianness-dependent.
Jira: ZEP-726
Change-Id: I950f8eaca7048bf7972c2c4c347cfd5bbba17eb6
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bug was introduced by a6cf6038e3
Change-Id: I91ceab2ca20c4d2f70a953b56d895152a471125a
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Provide a random driver wrapped around the KSDK RNGA driver.
Origin: Original
Change-Id: I43feeb37d8d5173c7b95af8e80434fb7dc77a83e
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In 1.0 you could set only one callback on the whole gpio controller. It
was impossible for another sub-system to add another callback, without
overwritting an existing one.
Such API has been obsolete for a long time and no one is using it
anymore. Thus removing it entirely.
Change-Id: I6a17fd99373dc6cef1fa2ebb421e992412d5015e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The LE_RAND HCI command was not filling in the rand array
with 8 random numbers as required by the spec.
Please note that the while() loop inside the command's
implementation can take up to hundreds of ms to execute.
Jira: ZEP-726
Change-Id: If27ff861ee5fa7842cd469e99d5bfa8ac47ac2fa
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Clean up, document and remove the macros used in hci.c
to access the different parameters and calculate lengths
of events and data structures.
Jira: ZEP-726
Change-Id: I476aa9e061dfe429b5181265167bffa203ed151b
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Switch to using the definitions in include/bluetooth/hci.h
for ACL data handling, both in RX and TX.
Jira: ZEP-726
Change-Id: I6b5f6de4ff568c4e73432df3edfa7d0a57f22fff
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Delete all event definitions from hci.c since the code now
uses the ones in include/bluetooth/hci.h exclusively.
This is the fourth and last commit in a series that transitions
from the event structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I625c2aecf759823a1cc73a3ea096564284fe8c52
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use Zephyr's include/bluetooth/hci.h for the HCI event
Number of Completed Packets.
This is the third commit in a series that transitions from
the event structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I179bceb2f9dc07d7a1a524c3a80f0886f712ec2b
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use Zephyr's include/bluetooth/hci.h for HCI event
handling in data-related events.
This is the second commit in a series that transitions from
the event structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I0e9e6f709091859af47d90b26f5e7baa830a2838
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use Zephyr's include/bluetooth/hci.h for HCI event
handling in control events.
This is the first commit in a series that transitions from
the event structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I6f131675add18e2ae061f0fb2cf220ea7057f852
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This changes the way that aysnchronous events are handled
in the BLE controller's HCI layer. It performs all common
operations in a single place to avoid code repetition of the
same memory accesses over and over.
Jira: ZEP-726
Change-Id: Id9e8395944e8800f32dd9749da2b4f5c901c8682
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Continue using Zephyr's include/bluetooth/hci.h for HCI command
handling in more of the commands.
This commit deletes all command and command complete and
command status event definitions and structures present in
hci.c.
This is the sixth commit in a series that transitions from
the structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I34635a1f55f3aef124fd5ff005c99cedb40b8a49
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
