STM32F0 flash driver already uses FLASH_PAGE_SIZE from HAL
in flash layout part, so CONFIG_FLASH_PAGE_SIZE is redundant
and confusing.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
For ISOOUT transaction, check if the buffer is empty before starting
the DMA and for ISOIN case check if the buffer is available to start
the DMA for IN transaction. This handling was swapped. So, handle it
accordingly.
Signed-off-by: Sundar Subramaniyan <sundar.subramaniyan@gmail.com>
Problem:
cdc_acm sample outputs junk characters to the console when any key
is pressed. It is supposed to echo the same character as the input.
Analysis:
nRF52840 USB driver always reads 64 bytes from the USB peripheral's
local buffer irrespective of the data length. Even when 1 byte
is sent by the host, the usb driver receives as 64 bytes.
Since the maximum packet size value had been used when setting up
the EasyDMA's MAXCNT register for OUT transactions, DMA transffered
the entire 64 bytes of it's local buffer into the data RAM
irrespective of the OUT data length, containing garbage at the end
of useful payload. For some applications like hci_usb the extra
bytes were being ignored. But for cdc_acm, the entire 64 bytes
is getting echoed back displaying garbled characters on the terminal.
Fix:
For OUT endpoints, the amount of data received by USBD to its local
buffer should be read using SIZE.EPOUT[x] registers in the case of
BULK and INTERRUPT endpoints and SIZE.ISOOUT register for ISOOUT
endpoint. This value should be set to the EasyDMA maxcnt register
to DMA into RAM buffer. Fix this issue for Bulk, Interrupt and
ISOOUT endpoints.
Signed-off-by: Sundar Subramaniyan <sundar.subramaniyan@gmail.com>
For now tx-fifo sizes are not configured (cf usb_dw_set_fifo).
Default fifo size is 136 bytes and sending more than 136 bytes
makes the data split into incorrect chunk size.
This patch prevents this by reducing available fifo size to a
multiple of the endpoint max packet size.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Fixes#6577.
Wait for all ongoing transmits to complete before de-asserting CS.
When doing a tx then rx, wait for the previous tx to complete before
flushing the rx buffer.
Tested on the Arduino Zero against a Olimex MOD-NRF24L module.
Signed-off-by: Michael Hope <mlhx@google.com>
Add console driver that allows console session to be transferred
over a websocket connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
* Add USB device controller driver for nRF52840 SoC.
* Supports only Bulk and Interrupt endpoints for now.
* ISO endpoint support is WIP.
What's tested:
* BTUSB - LE Scanning and connection.
Known issues in btusb tests:
* Observed momentary delays during LE scanning. This is possibly
due to hci_usb's way of calling the usb_write().
* Sometimes, when LE scan stop command is issued, response is not
sent and as a result USB stops functioning. This is also related
to the way btusb is handling the write(). For some reason, the
btusb class handler seems to issue another data packet write before
the USB control transaction is complete.
Miscellaneous:
* Lots of TODO items to discuss and fix.
Origin: Original
Signed-off-by: Sundar Subramaniyan <sundar.subramaniyan@gmail.com>
nRF52840 USBD requires power events to start USB enumeration.
Add APIs to enable/disable the power events, read the USB VBUS detect
and output power ready statuses which can then be used by the USB driver
in the enumeration sequence.
Signed-off-by: Sundar Subramaniyan <sundar.subramaniyan@gmail.com>
After porting the rand driver to drivers/entropy, replace the usage of
the old, Buetooth-specific driver with the generic entropy one.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The rand driver present in the BLE Link Layer is able to provide
entropy for both threads and ISRs, and so it is more suited to be used
as a generic nRF5x entropy driver instead of the current one. This will
allow applications and the Link Layer to use the same driver without
duplicating it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Adds a driver for SX1509B I2C GPIO chip. This driver only supports the
basic GPIO features and does not currently implement the LED driver and
keypad matrix features.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
SoC dts fixups are added and the i2c_nrf5 driver is modified to use
the values generated from the device tree.
The I2C_*_DEFAULT_CFG and I2C_*_IRQ_PRI options are removed from board
defconfigs. Bitrate and IRQ priority are configured using using the
device tree instead.
HAS_DTS_I2C is selected on all nrf5 boards to prevent generation of
conflicting defines from Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Keyword FLASH_HAS_PAGE_LAYOUT is related to flash and should
be declared in its Kconfig.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
It was possible to have enable flash module while no flash driver
implementation was enabled. This cause coverity issues and unnecessary
initialization call.
This pat introduce FLASH_HAS_DRIVER_ENABLED Kconfig keyword which is
selected once any flash driver is enabled. flash_map switch its
dependency to this keyword.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Fix Coverity "Memory - corruptions (ARRAY_VS_SINGLETON)"
issue by type casting word_to_write to u8_t pointer and
adding a length check before memcpy operation.
Coverity CID: 182779
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
The arithmetic performed on the CO2 and VOC measurements is pointless as
the units of the sensor already match those of the API, furthermore the
multiplication will overflow the u32_t with CO2 or VOC readings greater
than 4294 ppm or ppb. This CO2 concentration is achievable by breathing
at the sensor.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
A condition is added to the Kconfig file to disable config options which
will be supplied from the dts.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
This driver uses a bit-banging based technique of generating a signal
for the WS2812B LED strip. Since bit-banging is very timing sensitive,
where each CPU cycle counts, the driver uses inline assembly to
perform the most critical operataions. This initial version of the
driver only supports a Cortex-M0 implementation, and can e.g. be used
with the ZIP Halo LED strip for the BBC microbit:
https://www.kitronik.co.uk/5625-zip-halo-for-the-bbc-microbit.html
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
On a stm32, When we use the k_busy_wait function to wait a
delay (500us) just after an idle tickless period the delay could be
lower than the requested one. Consecutive readings of the cycle counter
made with the function k_cycle_get_32 juste after tickeless period
provides erroneous values (value jump) after some time (100 us).
To fix this issue we needs:
- Add the update of clock_accumulated_count value in the
_timer_idle_exit function.
- Treat the case in the get_elapsed_count function when the reload value
of the timer is set to a remaining value to wait until end of tick (see
_timer_idle_exit) . In this case the time elapsed until the systick
timer restart was not yet added to clock_accumulated_count. To retrieve
a correct cycle count we must therefore consider the number of cycle
since current tick period start and not only the cycle number since the
timer restart.
Fixes#6164
Signed-off-by: Holman Greenhand <greenhandholman@gmail.com>
Shell crashes when enter is pressed. This commit reverts relevant
changes from 14735116d1 that cause
this issue.
Fixes#6322
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
There are some minor differences between the UART om SAMD20 and SAMD21
that we need to take into account:
SYNCBUSY bit for the samd20 is located in the STATUS reg.
The samd20 does not have a SAMPR bit like the samd21.
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If we could not send the packet, then do not release the net_pkt
as that will be released in net_if.c:net_if_tx() if driver send()
fails.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
