Most of sensor channels defined by Zephyr use the main, unscaled
SI unit. We also have SENSOR_CHAN_ALTITUDE which is defined in
meters. So, it only makes sense to define distance in meters too
The only driver supporting SENSOR_CHAN_DISTANCE as of now is
vl53l0x.c, which was updated accordingly. Also, update doc links
in the driver based on the review comment.
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This patches fixes a few bugs with the SAM0 driver:
- txrx was trasnmitting too many bytes
- adds support for NULL buffers to the fast paths
- fixes a NULL dereference on the rx buffer slow path
The tests under tests/driver/spi/spi_loopback now pass.
Signed-off-by: Michael Hope <mlhx@google.com>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Add Altera Nios-II QSPI Flash controller driver which has
has 1024 blocks or sectors wich each sector size being 64K bytes.
This driver supports flash erase, write, read and lock operations.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Based on the discussion in #5693, the reason why humidity was defined
in milli-percent was likely following Linux which defines it as such
in its sensor subsystem:
http://elixir.free-electrons.com/linux/latest/source/Documentation/ABI/testing/sysfs-bus-iio#L263
However, Linux defines temperature in milli-degrees either, but
Zephyr uses degrees (similarly for most other quantities). Typical
sensor resolution/precision for humidity is also on the order of 1%.
One of the existing drivers, th02.c, already returned values in
percents, and few apps showed it without conversion and/or units,
leading to confusing output to user like "54500".
So, switching units to percents, and update all the drivers and
sample apps.
For few drivers, there was also optimized conversion arithmetics
to avoid u64_t operations. (There're probably more places to
optimize it, and temperature conversion could use such optimization
too, but that's left for another patch.)
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Now the native console driver also handles stdin
so we can drive the shell from the command line,
a pipe or a file
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Driver is 'Busy' can be a warning message which can be enabled with
minimum debug level CONFIG_SYS_LOG_IEEE802154_DRIVER_LEVEL=2.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Some mcu's have USART_PRESC_PRESCALER defined in the function call. Add
a prescaler of div1 to it.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
The default PWM polarity was 'inversed', which is not aligned with the
other PWM drivers. Unfortunately there is not yet an API to define the
default polarity to be used by the driver, but assume that 'normal'
(signal starts high for the duration of the duty cycle) should be the
default.
Signed-off-by: Ricardo Salveti <ricardo@opensourcefoundries.com>
Uses the new flash erase-block-size dts property to implement the flash
page layout api in the mcux flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the max30101 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxas21002 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxos8700 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Current buffers might be configured to skip data, thus only len will be
set, buf will be NULL. Buffer should be used if only len is > 0 and
buffer is valid as well.
tx/rx are "on" if len is > 0
tx/rx buf should be touched if only len is > 0 _and_ buf != NULL.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move to new Kconfig pattern in which we use an if !HAS_DTS_I2C_DEVICE
block for the Kconfig symbols that can now come from DT generation.
This pattern is useful to allow us to define default values for the
generated symbols for build-all testing.
Fixes: #5877
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Transfer is an important concept of USB specification.
During a transfer, several packets can be transmitted.
Today the usb API only provides ep_read and ep_write
functions but the transfer concept is missing.
This is typically ok for basic drivers which don't have
to take care of how data is transfered/splitted.
However there are some drivers like CDC EEM, in which
transfer concept is important for packet management.
Moreover, current ep-write and ep_read method have a
different implementation in usb_dc_dw and usb_dc_stm32
device drivers. For example usb_dc_dw supports only
1-data-packet transfers due to its implementation.
This can increase latency and reduce performance.
I think this is something we need to fix/improve by
implementing better transfer management.
This patch introduces usb_dc_ ep_transfer method which
can be used to configure IN/OUT transfers. This allows
to configure and request different transfer sizes and
should prevent usage of the current stm32 temporary
buffer.
This method has asynchronous and synchronous mode.
Synchronous mode waits for transfer completion before
returning. Asynchronouse mode (irq safe) configures
the transfer and returns immediately, the provided
callback will be then called on transfer completion.
This also update ep_write and ep_read stm32 implementation
to use this new method but keep their behavior unchanged
for legacy reasons.
Note that for now this method is local to stm32 device
driver, however the goal would be to expose this function
as a new USB device driver API method so that class
drivers use it. This will request same implementation in
the usb_dc_dw_driver.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
usb mass example need usb_dc_ep_read_wait/continue API.
test usb mass storage with RAM DISK on stm32f4 series.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Move to use an if HAS_DTS_I2C_DEVICE instead of depends on so that the
Kconfig sybmols don't even show up if HAS_DTS_I2C_DEVICE is true.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds pinmux defines to use I2C2 at PB10/PB11 for
stm32f0-based boards.
Needed for stm32f072b_disco board to use extension
connector
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
We want to move to use a common FLASH_DEV_NAME across the various flash
drivers. So samples, tests, or other code can be a bit more generic. So
replace CONFIG_SOC_FLASH_NRF5_DEV_NAME with FLASH_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
