Clean up whitespace etc. using clang-format after previous changes. No
functional changes intended.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Added support for interrupt-driven GPIO for this driver if an interrupt
line is defined. Note that interrupt support is optional in the GPIO
core so it may or may not be present.
The core provides a single state change notification whenever any line
changes state on a given bank, so we need to check the states of the
lines ourselves to determine what has actually changed.
Also, the driver treats the first and second GPIO banks as mostly
separate devices, but a single interrupt is shared by both banks, so the
ISR ends up being registered by the first bank which also triggers
handling on the second bank if required.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
The properties being read for the all-inputs and all-outputs flags in
the driver for the second GPIO channel did not match the ones listed in
the DT schema or the existing device tree files. Fix this.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Added to the configuration function to enable
channel chaining for the DMA_LPC that utilizes
the total of the SOC OTrig channels.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Use CONFIG_USB_DC_NXP_LPCIP3511 instead of FSL_FEATURE_USB_USB_RAM
as the behaviour variation is based on the SDK driver used and not
if the SoC has a dedicated USB SRAM.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Conditionally enable the USB_DC_HAS_HS_SUPPORT as the
USB_DC_NXP_LPCIP3511 controller can have both HS and FS only.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Ports the Jinghua Display JHD1313 LCD (with RGB backlight) driver
to use the new auxdisplay driver interface. This driver is used on
the seeed grove LCD RGB display, and replaces it.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
If you compile this code with Clang it will complain about casting a larger
type into a smaller enum.
```C
zephyr/drivers/clock_control/clock_control_nrf.c:120:37:
warning: cast to smaller integer type 'enum clock_control_nrf_type'
from 'clock_control_subsys_t' (aka 'void *') [-Wvoid-pointer-to-enum-cast]
enum clock_control_nrf_type type = (enum clock_control_nrf_type)subsys;
```
Adding `size_t` to the cast removes this issue. Another option could be to
add `-Wno-void-pointer-to-enum-cast` flag to the compile flags.
Signed-off-by: Sigvart Hovland <sigvart.hovland@nordicsemi.no>
The indended value for the delay after the software reset of adxl372 is
1ms. Adjust the value accordingly.
Fixes: a3e7cea
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Driver should just say the channel is not busy if
it is not setup rather than returning an error.
Also, change the channel index to int8_t rather
than uint32_t since it is being assigned negative
values and that width is more appropriate.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Clean up slashes in init macro to be less messy
Update copyright to reflect recent code changes by NXP
Update outdated driver description comment
Change irq driven api variables naming to be more specific
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The flexcomm uart mcux driver init macros have a lot
of unnecessary and confusing redundancy, so let's
simplify them.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The NPCX I2C controller has a port-controller hierarchy and the driver
is split in two files, with separate device struct and init functions.
These are currently initialized at the same level and priority, so the
actual order depends on what the linker does.
To avoid relying on the linking order, add a dedicated priority option
for the port that is set to go after the normal I2C one by default.
Found this by building with CONFIG_CHECK_INIT_PRIORITIES.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The uart_ite_it8xxx2 is relying on a node that depends on a matching
ns16550 symbol, such as:
ite_uart1_wrapper: uartwrapper@f02720 {
compatible = "ite,it8xxx2-uart";
...
uart-dev = <&uart1>;
};
But the two are currently setup to initialize at the same level and
priority. Add a dedicated priority symbol so that the wrapper device is
always initialized after the main one, regardless of the linker order.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Always clearing the interrupt status register was causing issues for
the sensor shell when interrupts were enabled but trying to read
one-off samples.
Signed-off-by: Yuval Peress <peress@google.com>
Update the sensor shell logic to use the new sensor_read() APIs and
make triggers an option of the sensor_shell sample (this avoids the
trigger stealing the interrupt status from one-shot reads).
Signed-off-by: Yuval Peress <peress@google.com>
Add a new async API based on the RTIO subsystem. This new API allows:
1. Users to create sampling configs (telling the sensor which channels
they want to sample together).
2. Sample data in an asynchronous manner which provides greater control
over the data processing priority.
3. Fully backwards compatible API with no driver changes needed for
functionality (they are needed to improve performance).
4. Helper functions for processing loop.
Signed-off-by: Yuval Peress <peress@google.com>
Enable direct framebuffer rendering using DCNANO LCDIF, to improve
performance when the call to display_write is attempting to refresh
the full display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable the ELCDIF driver to directly write the framebuffer using
hardware, when an entire framebuffer update is requested. This will
enable better performance for applications that avoid partial
display updates.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added intel LPSS DMA interface using dw common to support
usage of internal DMA in LPSS UART, SPI and I2C for
transfer and receive operations.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Added support for 64bit address source and destination
usage for dw common.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Use the DMA reload flag to indicate we wish to use
a circular chain of DMA descriptors to reload DMA
receive buffers.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
1. Transfers are not limited by XFERCOUNT transfer length of
LPC DMA descriptor. Added code to handle block sizes
greater than XFERCOUNT.
2. Use the reload_en flag to decide if we should setup
a circular descriptor chain.
3. Improve handling of source and destination width.
4. Number of DMA descriptors are defined by a Kconfig value.
5. Changed the dma_reload function to handle transfers
greater than XFERCOUNT.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The OpenTitan watchdog driver is a watchdog driver that can be configured
with two stages: a watchdog "bark", which generates an interrupt, and a
watchdog "bite", which resets the system. The two-stage watchdog can be
enabled by setting CONFIG_WDT_MULTISTAGE=y. Otherwise, the driver
functions as a single-stage watchdog.
A callback function may be set for the bark interrupt through the
wdt setup interface, but will only be used if the two-stage watchdog is
enabled. It must be configured for the first watchdog stage.
The driver controls only the watchdog portion of the OpenTitan AON timer.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
All posix arch boards are required to provide the same
tracing/print API.
So, instead of having a different driver for native_posix and the
bsim boards, let's have a common one which uses this API.
This in turn results in the printk strings being printed in
the same underlaying backend as before with individual drivers.
A part from this, the native_posix console driver was a full
backend for the now long gone Zephyr console shell
(named legacy_shell from 527256501f
until it was retired in fd0b7f7767).
The whole input handling in this driver was dead code
(since 140a8d0c8a)
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commit enabled the Silicon Labs Bluetooth interface driver on the
EFR32BG27 SoC series in the Kconfig.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commits adapts the driver to the newer version of the EFR32 BT
blobs:
* libbluetooth_controller
* libbgcommon
* librail
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Since not all GPIOs support voltage selection, configure voltage
selection register only if it is present.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This adds support for the USB interface for the
Renesas Smartbond DA1469x device family.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
Copy the LUT to SRAM before updating it. This avoids the application
reading LUT entries from FlexSPI while trying to write them to FlexSPI
configuration registers, which could result in invalid LUT entries being
added.
This update is applied to all in tree flash FlexSPI drivers, although
the failure has only been observed with the flash_mcux_flexspi_nor
driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add I2C target mode support for NPCX i2c driver. Verified with
i2c_target_api test suite on npcx9m6_evb.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Clean up the include/source lists in the sensors subsystem. Sort the
list, drop the empty lines that makes it look super long for no good
reason, get away with the tabs to align the file names that does not
really work anyway.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This make MCUboot build as Zephyr application.
Providing optinal 2nd stage bootloader to the
IDF bootloader, which is used by default.
This provides more flexibility when building
and loading multiple images and aims to
brings better DX to users by using the sysbuild.
MCUboot and applications has now separate
linker scripts.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Like other stm32 drivers, especially the stm32 flash ospi,
the DMA callback accepts a null or positive status.
It returns an error in case of negative.
BTW it also sets variable as unused, like stm32 flash ospi does.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Define two macros for calibration and oversampling for STM32 series that
possess these features, and use these macros instead of a list of series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Rework oversampling by creating a const table containing possible
oversampling values and using this table instead of switch case.
Also disable ADC for all series before setting oversampling.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
