This patch handles multiple interrupt lines for errors. Each of the
4 DW SPI error interrupts (txo_err, rxo_err, rxu_err, mst_err) can
use a different line of the GIC, instead of using a single line of
the GIC for all error interrupts (err_int).
Signed-off-by: Julien Panis <jpanis@baylibre.com>
This patch manages DW SPI driver MMIO region. As a result, the driver now
runs properly on 64 bit platforms.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
When CONFIG_SYSTEM_SLOPPY_IDLE is not set, then system
can sleep for -1 means waking Up at the max possible
counter value (INT_MAX)
When CONFIG_SYSTEM_SLOPPY_IDLE is set sleeping K_TICKS_FOREVER
means never wakingUp
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Provide multiple write transaction support for BlueNRG-MS, st_hci_spi_v1
protocol. Since by default, BlueNRG-MS write buffer supports up to 127
bytes; however, it is possible to have consecutive write transactions
so as to send data more than 127 bytes.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Added IS_ALIGNED macro to check if a pointer is aligned to
a given alignment. Additionally, removed a macro with a
conflicting name in drivers/crypto_intel.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Adds conditional usage of locking mechanisms to allow building
without multithreading.
Signed-off-by: Mateusz Michalek <mateusz.michalek@nordicsemi.no>
Now RRAMC is set to use up to 512 B burst writes by default as most
time effective.
Requested slot time was changed to 8000 us for that case, as this is
required in order to hold the longest write operation.
Drivers differs slot duration depending on configured RRAMC buffers count
(CONFIG_NRF_RRAM_WRITE_BUFFER_SIZE).
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
When radio-synchronization was on
(CONFIG_SOC_FLASH_NRF_RADIO_SYNC_NONE=n) context of writing was shifted
by 4 instead of write-length (this caused redundant, self-shortening
writes to the same block.)
write-len was unset when requested write len was less than
RRAM_MAX_WRITE_BUFFER.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Added synchronization with BLE radio operation to the RRAM flash
driver. The implementation is using framework which is already
provided for nrf52's flash driver.
Additional added resource locking mechanism while driver does writing
which solves mutual exclusion write access problem.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Added a simple driver for RRAM. It is implemented as a flash driver,
because the "RRAM eFlash" macro obeys flash-like constraints.
Although users are not required to erase before write.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Add driver for ScioSense ENS160 multi-gas sensor. The driver includes
support for I2C and SPI, attributes for setting temperature and
humidity compensation and data ready trigger.
Also add ScioSense to the list of vendor prefixes.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
Process the GPIO_INT_WAKEUP flag and set appropraite bits
in the SoC to wakeup the system from deep sleep mode.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The network tests at tests/net use simulated network interfaces
and set CONFIG_NET_TEST to indicate that. If the config option
is set, then we do not want any extra Ethernet driver to
complicate the testing scenario so all external Ethernet
network interfaces should be disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Cast val1 from sensor_value before multiplication in order to avoid
integer overflow, as indicated by Coverity CID 347136.
Signed-off-by: Renato Soma <renatoys08@gmail.com>
PR #64399 introduced checks for out-of-bounds filter IDs
in CAN drivers, along with logging of said IDs; however,
the call to LOG_ERR in the native POSIX/Linux driver is
missing the 'filter_id' argument.
This commit adds the missing argument to ensure proper
data is printed when the LOG_ERR call is performed.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The pin in the loop start counting from 0, so the condition of the
for loop should not be equal to num_pins.
Fixes#69118
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Clearing virtual wire interrupt after calling handler may cause next
interrupt miss if the same virtual wire changes due to action in handler.
As the interrupt source is read from register, it can be cleared before
calling handler to avoid next interrupt miss due to action/delay in the
callback handler.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69129
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69133
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69132
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69131
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use K_KERNEL_STACK_SIZEOF() for calculating thread stack size, as this
takes K_KERNEL_STACK_RESERVED into account.
Fixes: #69130
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fix missing check of the return value of `bq25180_set_charge_current`
function, resulting in logically dead code, as indicated by Coverity
CID 347197.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
- Fix using custom setup function
- Enable pRegOverrideTxStd and pRegOverrideTx20 in
ieee802154_cc13xx_subg_radio_div_setup struct
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
The driver seems to be designed to use the very last byte of the
buffer(scan, connect), so null terminating the status query
might have unintended consequences.
However we should not use strlen to determine the ssid_len,
to avoid depending on the following buffer(bssid) to be zeroed.
Related to CID 316354
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Clearing virtual wire interrupt after calling callback may cause
interrupt miss if the same virtual wire changes due to action
in handler.
e.g. HOST_RST_WRN pulse within 50 us
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
device power management is not yet supported with eth_mcux
except on the kinetis series, but this should not break
the build for other platforms when PM_DEVICE is set
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
A division by 0 has once been observed inside
intel_adsp_hda_dma_host_reload(). It is apparently caused by a
preceding logic or hardware error, but in any case values, read from
the hardware should be checked for 0 before being used as a divisor.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Due to a typo it is not possible to select the sub-clock oscillator
(SOSC) as a clock source for an RA Microcontroller. This patch resolves
the issue.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
Fix handling bus-off events in the Bosch M_CAN driver backend:
- Cancel all pending TX buffers when entering bus-off state
- Call all pending TX buffer callbacks with -ENETUNREACH when entering
bus-off
- Automatically initiate bus-off recovery if
CONFIG_CAN_AUTO_BUS_OFF_RECOVERY=y
Fixes: #68953
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
If the IPv6 DNS address is not a valid address, DNS will fallback
to the IPv4 DNS address.
Fix copying the IPv4 address to the IPv6 address by using
the IPv6 address destination length.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
The lower bits of the brightness control registers were erroneously
shifted even though FIELD_PREP already does the shifting. In practice,
the effect is negliglible but of course should be fixed.
Also add missing parenthesis around shifting operations to satisy static
analysis.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Replace slave_register with target_register and slave_unregister
with target_unregister.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Driver BBRAM for STM32 had a compilation error: "unknown type name
'RTC_TypeDef'" due to missing include file.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
The conversion of the raw sensor value overflows because
only a 32 bit multiplication is executed.
Fix the issue by promoting the raw sensor value to uint64_t before
executing the multiplication.
Analysis:
The current implementation overflows for all raw values grater
than 9544(14-bit).
But according to the datasheet the sensor has a maximum resolution of
20-bit. So Multiplying that value with 450.000 would need at least 39
bit to avoid an overflow, hence do it using 64-bit arithmetic.
Fixes CID 330657
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
