Convert lis3dh accelerometer driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
FIX issue #10571 and #10593
atomic_xxx() functions expect the bit argument to be the
position index inside the target integer and not its
numerical representation (e. g. 5 means the 5th bit and not 32).
The original code could potentially override an adiacent variable.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The sensor signal cannot be cleared by the application, so enabling
level triggers causes the system to hang as the callback is invoked
repeatedly. We want notification when the alarm state is entered, and
when it's exited, so use a double edge.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add symbolic names to bus type (LIS2DH_BUS_TYPE) and trigger mode
(LIS2DH_TRIGGER_MODE) in order to be defined in board defconfig
files.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis2dh accelerometer driver to get the device name as well
as i2c/spi slave information from device tree. Updates the build_all
test accordingly. (issue #11605)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Remove an unnecessary local variable to store the
return value, instead return directly thereby saving
few bits of memory.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Converts the adxl362 sensor driver to get the device name and spi slave
properties from the device tree rather than Kconfig. Updates the
build_all test accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the BMI160 to use Device Tree to get SPI and GPIO params instead
of Kconfig. Updated samples, tests, and arduino_101_sss board support
for this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Couple of findings which were revealed after changing
LOG_MODULE_REGISTER macro:
- missing semicolons after LOG_MODULE_REGISTER()
- missing LOG_LEVEL defines
- other
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Provide necessary error handling for `lis2dh_reg_read_byte` function
which might fail.
Also, use a common `status` variable to be used for storing the
error code.
Fixes#10590
Coverity-CID: 188733
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Remove the redundant semicolon used as a terminator in
`if`, `switch`, `while` statements.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
i2c_burst_read can fail during read/write procedure. Therefore,
add a sanity check for its return value.
Fixes#11101
Coverity-CID: 189505
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Driver for LSM303DLHC accelerometer now supports API function
sensor_attr_set for attribute SENSOR_ATTR_SAMPLING_FREQUENCY.
Signed-off-by: Dennis Wildmark <d.wildmark@gmail.com>
Macro is used to create contiguous bitmask between the
arguments passed to the macro.
BITS_PER_LONG is computed as the multiplication of predefined
macros `__CHAR_BIT__` and `__SIZEOF_LONG__`.
Both gcc and clang support these predefined macros.
With this change, replace the redundant defintions of
GENMASK with the new generic macro available.
Fixes#10843
Suggested-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Check the return value of i2c_reg_read_byte() and return
if unable to read the register
Coverity-CID: 188740
Fixes#10585
Signed-off-by: Satya Bhattacharya <satyacube@gmail.com>
Driver fxos8700 can also be used for the MMA8451
accelerometer and offers more functionality.
Revert the commit to avoid duplicate code.
This reverts commit 9c0d7813e5.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add basic verification of the supported devices.
Add IDs for MMA8451, MMA8652, MMA8653 and FXOS8700 and
remove Kconfig FXOS8700_WHOAMI option.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The existing API defined sys_clock_{hw_cycles,ticks}_per_sec as simple
"variables" to be shared, except that they were only real storage in
certain modes (the HPET driver, basically) and everywhere else they
were a build constant.
Properly, these should be an API defined by the timer driver (who
controls those rates) and consumed by the clock subsystem. So give
them function syntax as a stepping stone to get there.
Note that this also removes the deprecated variable
_sys_clock_us_per_tick rather than give it the same treatment.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Added support to LIS2MDL Magnetometer sensor provided
with following features:
- I2C interface
- Mag data
- Temperature data
- ODR configurable by config or at runtime
- Trigger mode selectable by menuconfig
- IRQ pin configurable (by dts or Kconfig)
- Hard Iron offset setting at runtime
- Include yaml file
Tested on ST MEMS IKS01A2 + NUCLEO STM32F411RE board.
LIS2MDL connected to I2C master interface (SPI 3 wire not
supported yet).
Test run with all ODR {10, 20, 50, 100} Hz in poll and
trigger mode.
GPIO IRQ dts configuration has been tested by adding
to boards/arm/nucleo_f411re/nucleo_f411re.dts file
this patch:
&i2c1 {
status = "ok";
clock-frequency = <I2C_BITRATE_FAST>;
+
+ /* ST Microelectronics LIS2MDL mag sensor */
+ lis2mdl-magn@1e {
+ compatible = "st,lis2mdl-magn";
+ reg = <0x1e>;
+ irq-gpios = <&gpioa 4 0>;
+ label = "LIS2MDL";
+ status = "ok";
+ };
};
and adding boards/arm/nucleo_f411re/dts.fixup with following
content:
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_LABEL
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BASE_ADDRESS
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BUS_NAME
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_CONTROLLER
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_PIN
For more info on this LIS2MDL please follow this link:
http://www.st.com/en/mems-and-sensors/lis2mdl.html
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_PINS and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
