Remove CONFIG_IPM_IMX_REV2, as this Kconfig is no longer needed. The
driver can now be enabled with CONFIG_IPM_IMX.
Update NXP HAL to remove this Kconfig as well.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The ipm_cavs_idc driver was used with the old intel_s1000
board which has been removed. On the audio DSP side,
the IDC under CAVS is being handled by SoC layer code.
Now the ipm_cavs_idc is not needed anymore for anything.
So remove it.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add ipm driver to use Inter Processor Interrupts
on Xilinx ZynqMP platform. This patch also adds sample
application that shows use of xlnx ipm driver.
This driver uses default arm gic interrupt controller
and works only for lockstep mode of cortex-r5f
cluster for now.
In split mode the cortex-r5 cluster will
have two r5f cores and they are expected to work in AMP
mode. If both r5f cores run simultaneouly, only one of
the core is able to receive IPI interrupts at this time
and it will be the one that started later. In future
this limitation shall be removed.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
This driver is built on top of the IVSHMEM doorbell
notification mechanism providing an unified way
to generate inter VM interrupts.
Signed-off-by: Felipe Neves <felipe.neves@linaro.org>
This adds a few line use zephyr_syscall_header() to include
headers containing syscall function prototypes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Intel Audio DSPs have "IPC" interrupt delivery and shared memory
window hardware. The Sound Open Firmware project has historically
used the combination of these to implement a bidirectional
message-passing interface. As it happens, this protocol is an
excellent fit for Zephyr's somewhat geriatric but still useful IPM
interface.
This implements a SOF-protocol-compatible transport that will
hopefully prove a bit more futureproof for non-Intel SOF
architectures. It is a software-only device, built on top of the
underlying SOC APIs for the SRAM windows (in cavs-shim) and IPC
(cavs_ipc).
Note that SOF actually has two protocol variants (ipc3 and ipc4): in
both, the command header (passed as the "id" parameter in IPM) is sent
via the hardware doorbell register. But in ipc4, the second hardware
scratch register is used to transmit the first four bytes of the
command before involving the SRAM window (in ipc3, it's ignored).
Both modes are supported by this driver, set IPM_CAVS_HOST_REGWORD to
choose the "ipc4" variant.
Finally: note that the memory layout for the windows in question is
inherited from SOF, and for compatibility (with both SOF and with the
offsets used by the host!) these can't be changed without major
surgery. They're defined in kconfig, but should be treated as
read-only until we get a chance to rework the way Zephyr does its SRAM
window management (and probably in concert with the host drivers).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
With a number of the i.MX SoCs (e.g., the i.MX8M Plus), NXP has moved to
supporting the integrated Cortex-M cores with the MCUXpresso SDK (MCUX).
As a result, certain Zephyr drivers (such as the IPM driver) need to be
updated to utlize this new MCUX-based SDK.
This change adds support for the MCUX Messaging Unit driver pulled in by
this PR:
https://github.com/zephyrproject-rtos/hal_nxp/pull/130
Additionally, this change enables the new IPM_IMX_REV2 config for the
mimx8ml8_m7 SoC target which utilizes this new revision of the driver.
Signed-off-by: Chris Trowbridge <chris.trowbridge@lairdconnect.com>
This is dead code. It's based on the cAVS "IPC" mechanism to allow
communication to and from the host CPU. But there is no test rig in
the Zephyr tree for the protocol defined. And in fact the only
Zephyr-based user of the IPC mechanism (Sound Open Firmware) has its
own IPC driver and speaks its own protocol with the host kernel. That
driver needs to migrate into Zephyr soon and this legacy bit is just
confusing.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Some STM32 SOC, like stm32h745 and stm32h747 doesn't have IPCC.
Provide a STM32 HSEM based ipm driver for these SOC.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
This set of functions seem to be there just because of historical
reasons, stemming from Kbuild. They are non-obvious and prone to errors,
so remove them in favor of the `_ifdef()` ones with an explicit
`CONFIG_` condition.
Script used:
git grep -l _if_kconfig | xargs sed -E -i
"s/_if_kconfig\(\s*(\w*)/_ifdef(CONFIG_\U\1\E \1/g"
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This adds a rather primitive driver for use with the Intra-DSP
Communication (IDC) on the DSP on certain Intel SoCs. The IDC
generates interrupts from one core to another by writing to
certain registers. This is also being utilized as
the scheduler IPI since it can interrupt other cores.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add driver for i.MX Messaging Unit peripheral which can be used for
i.MX6SoloX, i.MX7D and other i.MX socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
