Add I2C Master driver for Nios-II I2C soft IP core.
This driver relies upon the Altera HAL I2C driver for all the bus level
transactions, interrupt handling and register programming.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Just some exclusions to coverage in code which cannot be
reached, or can only be reached in error conditions
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added possibility to reconfigure CONFIG_SYS_CLOCK_TICKS_PER_SEC
for the native_posix board (before it could only be 100)
+
Fixed tickless idle support
+
Minor fixes in irq wrapping
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Whenever a Cortex-M0+ supports the VTOR register it makes no sense to
use the software vector relay mechanism. Therefore change the logic so
that SW_VECTOR_RELAY does not get enabled whenever a VTOR register is
present, but enable it if an M0+ has no VTOR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In a scenario where a platform harbours multiple interrupts to the
extent the core cannot support it, an interrupt controller is added
as an additional level of interrupt. It typically combines several
sources of interrupt into one line that is then routed to the parent
controller.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patch adds the generation and incorporation of privileged stack
regions that are used by ARM user mode threads. This patch adds the
infrastructure for privileged stacks. Later patches will utilize the
generated stacks and helper functions.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds application data section alignment constraints
to match the region definition requirements for ARM MPUs. Most MPUs
require a minimum of 32 bytes of alignment for any regions, but some
require power of two alignment to the size of a region.
This requires that the linker align the application data section to
the size of the section. This requires a linker pass to determine the
size. Once this is accomplished the correct value is added to a linker
include file that is utilized in subsequent linker operations.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Replace seldom occurrences of FLASH_DRIVER_NAME by equivalent
and commonly used FLASH_DEV_NAME.
Fixes#5919.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Some ARMv6-M Cortex-M0+-based SOCs have VTOR register
and can relocate vector table just as ARMv7-M ones.
Vector table relocation path should be choosed
by VTOR presence, not by arch.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Add Altera Nios-II QSPI Flash controller driver which has
has 1024 blocks or sectors wich each sector size being 64K bytes.
This driver supports flash erase, write, read and lock operations.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Some code in the POSIX architecture is only meant to handle
safely errors which should never occur and therefore
are not covered.
=> We exclude them from the coverage reports.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Some code in the POSIX SOC (inf_clock) will only be executed
if the program is terminated by receiving a SIGTERM in a particular
part. Therefore to avoid confusing developers with changing
coverage, let's exclude it from the coverage reports.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Some code in the POSIX arch core will only be executed
in some very atypical cases depending on the host load.
To avoid confusing developers, let's exclude it from the
coverage reports.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added a new config variable with the recommended stack
size for threads which are only meant for the posix architecture
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Defines the FLASH_DRIVER_NAME macro in soc.h for kinetis kl2x and kwx
SoC series. This macro is used by the storage and dfu subsystems, as
well as the flash_shell sample.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rename the nano_internal.h to kernel_internal.h and modify the
header file name accordingly wherever it is used.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
rename main_clean_up() to posix_exit() for consistency
with all other global functions of this architecture
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Currently in zephyr the support for the arm userspace has not be
merged. But the Kconfig always sets the userspace flag and causes a
build failure. This is blocking the test cases for userspace.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add a new Kconfig option, BOOTLOADER_MCUBOOT, that automatically sets
the required options necessary to make the resulting image bootable by
the MCUboot open source bootloader. This includes the text section
offset and the vector relay table for Cortex-M0, and in the future it
might also add the DTS overlay required to link at slot0 offset in
flash.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add device tree support for the "nxp,kinetis-ftfa" flash controller used
on the NXP KL2X and KW4xZ SoCs.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The old HAL and MDK have been removed from the source tree.
Since RADIO HAL is not yet present in nrfx, the "nrf_radio.h" file
was temporarily moved to "nrfx/hal" folder. It will be replaced with
the proper file from nrfx in its next update.
Signed-off-by: Michał Kruszewski <michal.kruszewski@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit adds a glue layer that adapts nrfx to be usable in Zephyr
as a host environment and files with static configuration of nrfx
drivers for several supported SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This moves and merges the existing board-level dts.fixup files
for STM32 L4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
disco_l475_iot1 boards fixup blocks for devices connected via SPI
and I2C stay in board level dts.fixup file, because they are board
specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F3 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F1 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
96b_carbon boards fixup block for Bluetooth HCI device via SPI
stays in board level dts.fixup file, because it is board specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F0 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For SoCs that don't support vector table relocation in hardware, may not
support bootloader like mcuboot.
We introduce a way to relocate vector table in software by forwarding
the control of incoming IRQs to a new vector table which address is save
at fixed SRAM address.
User can change the data in that fixed SRAM address in order to relocate
vector table in software way.
Signed-off-by: Ding Tao <miyatsu@qq.com>
Cortex-M0 do not have the Vector Table Base Address Offset Register, so
Cortex-M0 vector table address can not be changed.
But in some Cortex-M0 SoCs like STM32F0 series, they have some mechanism
that can remap the vector table address to the start address of SRAM.
Use this flag to indicates whether current Cortex-M0 SoC support such a
remap or not.
Signed-off-by: Ding Tao <miyatsu@qq.com>
In order to be able to build MCUboot for nRF51 we require the flash
driver name in the nRF51 soc.h header.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
