Move common config options one level up to try to simplify the per-board
defconfig
Change-Id: I3d80fa494050634d0f877af2015b01b85df20d1d
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the STM32F401 chip on the board
Change-Id: I96c0799f3658ecea096fa5971bce9faf21919ee1
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F401 allows for upto 16 alternate functions on each pin.
Change-Id: Ib1c14fd31abaa2b05a5ab0f7bd1b4a4748f10f84
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements MCU-specific GPIO input interrupt integration. Added
definition of System configuration controller as well as its needed by
the GPIO code.
The SYSCFG controller is used for system-specific configuration such as:
- remap the type of memory accessible at address 0x00000000
- manage the external interrupt line connection to GPIOs
- configure the I/O compensation cell
Change-Id: Id2ebfbd1b21e77be76406d1cd6cd5d4989e9e2fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Based on the STM32F10x driver. Removing old code as we need to use the
bus number when dealing with 4 possible peripherals.
Change-Id: Id0263aa008e9b039ff9a00339e5622e289ffdf99
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds support for the STMicroelectronics STM32F4x family in the
STM32 MCU line. Configuration is included for the STM32F401RE MCU.
Acknowledgements to Pawel Wodnicki's earlier submission from February that
was used as a starting point for this port. In the end, we rewrote all of it.
Change-Id: I9797c282ac3c0cc66a63b9d34821de95df537ef6
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Fix the error in thread rescheduling:
Fix Fast IRQ exit routine error when it reschedules threads if
(prio >= 0) || (sched_locked == 0) || (next_thread == _current),
while the correct condition for thread rescheduling is:
(prio >= 0) && (sched_locked == 0) && (next_thread != _current),
Fix regular IRQ error when the regular IRQ exit routine rescheduled
threads when (next_thread == _current) instead of
(next_thread != current).
Increased IDLE_STACK_SIZE for ARC architecture, to hold saved
registers.
Change-Id: I1d87a968e231e13822844b7564567e6ca310cde2
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The mk64f12 provides RNGA hardware. Follow the implementation pattern
used by various other driver classes and enable the RANDOM KSDK shim
driver if the RANDOM driver is enabled.
Change-Id: I46bdf16cf1c48937011fb1b0e4c292615efd4c95
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
They were the same, standardize on the lowercase one.
Change-Id: I8bca080e45f3e0970697d4451e468b9081f96f5f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
SOC_TI_LM3S6965 and UART_STELLARIS are platform-specific, remove from
arch/arm/defconfig.
Change-Id: I3b37bc2ddfabb1da4e7538b5ab0e553fb2464584
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
STM32F4 requires the alternative function config to be set, so just
initialize that as part of the gpio configure call.
Change-Id: I33a4a8efec59c5ebe7dc3f3580f0dd2bf7ded7f4
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
The STM32F1 range all have the independent watchdog, enable the driver
by default if CONFIG_WATCHDOG is enabled.
Change-Id: I3869884dc51c56194367b46007c87f6cee699689
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
All M7 features common to M3/M4 are working. New features like Tightly
Coupled Memory (TCM) are not yet supported.
Change-Id: I5f7b292e70843aec415728f24c973bb003014f4b
Jira: ZEP-977
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
With this patch we introduce unified kernel support for NIOS II.
Not all test cases have been ported, but the following command
currently succeeds with 43/43 passing test cases:
$ sanitycheck --arch=nios2 -xKERNEL_TYPE=unified \
--tag=unified_capable
Issue: ZEP-934
Change-Id: Id8effa0369a6a22c4d0a789fa2a8e108af0e0786
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Existing code wasn't removing a thread from the kernel's list
of active threads if the thread terminated or aborted. (It did
remove it if the delayed starting of a thread was cancelled.)
Change-Id: Icc97917e33765696480d0e9bf31e882ef555d095
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Gets rid of unnecessary THREAD_MONITOR_INIT() macro, to be
consistent with the approach taken by _thread_monitor_exit().
Aligns x86 code with the approach used on other architectures.
Revises the associated comments and removes unnecessary
doxygen tags.
Change-Id: Ied1aebcd476afb82f61862b77264efb8a7dc66c9
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Renames _thread_exit() to _thread_monitoring_exit() to make
its purpose clearer. Revises the associated comments and
removes unnecessary doxygen tags.
Change-Id: I010a328d35d2d79d2a29b9d0b6c02097bb655989
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
The baudrate calculation present in set_baudrate() is
causing the UART to emit inital bytes incorrectly, for a
reason currently unknown, but directly related to the fact
that __aeabi_uldivmod is being invoked.
Since the nRF5x Product Specifications do not provide a
standard formula to calculate baudrates and instead list
a predefined set of divisor values, we opt here to use the
official values and remove the attempt at calculating them
manually.
Change-Id: Ic3ff42ea6d065e9a1d26a5350ce5bf5ad661160a
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Several platforms utilize a ihex image format. Rather than
duplicating the build bits in everyones makefile, pull it into the
toplevel makefile so we all share it.
Change-Id: I9097b06e7e386a69ce6ab4d4e4d56cc776adfec2
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- the interrupt (both regular and fast) now does not do rescheduling
if the current thread is a coop thread or if the scheduler is not locked
- the _nanokernel.flags cache of _current.flags is not used anymore
(could be a source of bugs) and is not needed in the scheduling algo
- there is no 'task' field in the _nanokernel anymore: scheduling routines
call _get_next_ready_thread instead
- the _nanokernel.fiber field is replaced by a more sophisticated
ready_q, based on the microkernel's priority-bitmap-based one
- thread initialization initializes new fields in the tcs, and does not
initialize obsolete ones
- nano_private includes nano_internal.h from the unified directory
- The FIBER, TASK and PREEMPTIBLE flags do not exist anymore: the thread
priority drives the behaviour
- the tcs uses a dlist for queuing in both ready and wait queues instead
of a custom singly-linked list
- other new fields in the tcs include a schedule-lock count, a
back-pointer to init data (when the task is static) and a pointer to
swap data, needed when a thread pending on _Swap() must be passed more
then just one value (e.g. k_stack_pop() needs an error code and data)
- the 'fiber' and 'task' fields of _nanokernel are replaced with an O(1)
ready queue (taken from the microkernel)
- fiberRtnValueSet() is aliased to _set_thread_return_value since it
also operates on preempt threads now
- _set_thread_return_value_with_data() sets the swap_data field in
addition to a return value from _Swap()
- convenience aliases are created for shorter names:
- _current is defined as _nanokernel.current
- _ready_q is defined as _nanokernel.ready_q
- _Swap() sets the threads's return code to -EAGAIN before swapping out
to prevent timeouts to have to set it (solves hard issues in some
kernel objects).
Change-Id: Ib9690173cbc36c36a9ec67e65590b40d758673de
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Still missing a working timer driver, as SysTick is not really available
in this SoC series (enabled to avoid build issues, but not used).
Jira: ZEP-784
Change-Id: Ie1c8e6c5e8955ee7f260ce013f4451f9215f3457
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Integrating the IRQ definitions for both nRF51 and nRF52, and defining
the set of IRQ values that are common to both.
Also switch the controller, uart and clock drivers to use the common
header definitions.
Change-Id: Id6816d7a97720896cfe4df83656fb8b1f8fb01fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Not disabling SysTick as it is optional by the spec.
SVC not used as there is no priority-based interrupt masking (only
PendSV is used).
Largely based on a previous work done by Euan Mutch <euan@abelon.com>.
Jira: ZEP-783
Change-Id: I38e29bfcf0624c1aea5f9fd7a74230faa1b59e8b
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
EM7D was recently merged, and one change suggested there was
to remove conditional checks for NSIM. It is OK to have the simulator
use the exact same memory addresses and sizes as would be found on the
board. This submission fixes EM9D and EM11D to be the same -- i.e.
to not have NSIM conditionals.
See ZEP-966.
Change-Id: Ia990ff7bb4b7ff5071af83723ed3d1420fdff012
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
The EM7D SOC is similar to EM11D, except it has different sized
iccm and dccm memories, and also has FIRQ with RGF_NUM_BANK==1.
To select this SOC on the board, all dip switches are in the up position.
See ZEP-966.
Change-Id: I864ffe0efdf367de0a8cd58e9c46efd7e401c671
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
For the EM Starterkit, one SOC I will soon be adding is EM7D.
This SOC has FIRQ, but only has one register bank.
Thus the interrupt handling for FIRQ needs to be different
when CONFIG_RGF_NUM_BANKS==1. The handler must instead push
registers onto the stack in the same stack frame layout that RIRQ uses.
This allows for context switch to be easily done since its compatible.
The common interrupt entry point _isr_enter must save r0 before using
it, because in the FIRQ 1-bank case, it would be destroyed otherwise.
So a global variable named saved_r0 has been added for this reason.
The stack cannot be used to save r0, because it first has to determine
whether its FIRQ or RIRQ here. This change has been tested on the
EM Starterkit with EM7D SOC changes -- coming soon. To make the review
easier, these 3 files are submitted first.
Also, exceptions will no longer use the _firq_stack.
This stack is not needed in the 1-bank case, but an exception stack
is needed. I've added a new stack called _exception_stack,
and made it be 512B, which should be enough for one exception.
See ZEP-966
Change-Id: I6f228b840da7c4db440dd1cfef4ae25336c87f0d
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Those options are not being used anywhere, so remove them and avoid some
confusion.
Change-Id: Ia3767dbd2432851dfae4b1e996f02ed1b2450505
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Bluetooth controller implementation requires the low power
oscillator for radio time space scheduling and as sleep
clock; the high frequency oscillator as the active clock.
For Nordic Semiconductor's nRF5 Series SoC's select the
NRF Clock peripheral when BLUETOOTH_CONTROLLER is selected
in Kconfig build.
Jira: ZEP-897
Change-id: I6f99e90b3485e757be61e91c749e485dd0cfdaba
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
The driver performs one shot PHY setup. There is no support for PHY
disconnect, reconnect or configuration change. The PHY setup,
implement via KSDK contains polled code that can block the
initialization thread for a few seconds.
There is no statistics collection for either normal operation or error
behaviour.
Origin: Original
Change-Id: Ia0f2e89a61348ed949976070353e823c178fcb24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
There is a convention in the soc implementation for other
(non-ethernet) classes of driver that enabling a generic driver has the
effect of enabling the specific flavour of driver required for the
board. Extend this convention such that when ETHERNET is enabled, the
quark_x1000 enables the DW ethernet driver.
Change-Id: I525471d259c9582024cd44d6cc4557260abe6451
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Build breaks when enabling CONFIG_NEWLIB_LIBC because it has its own
sched.h file.
This is a bad symptom of a greater issue: the build system passes many
'-I<path>' options to the compiler, and that allows including header
files by simply specifying their names (when located somewhere else than
<zephyr>/include/) and can cause clashes when several files in different
locations have the same name, like in this case.
Fixes ZEP-1062.
Change-Id: I81d1d69ee6669a609cd0c420b1b8f870d17dcb67
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Builtin might not be available for ARMv6 (Cortex-M0/M0+) depending on
the toolchain used (not available by Zephyr's SDK GCC), so move the
atomic operations selection to the Cortex-M family Kconfig file.
Change-Id: I20a5a0c5fdd2bcff2d304139f5a7e8502fdb1cb3
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
When adding a thread to the ready queue, it is often known at that time
if the thread added will be the next one to run or not. So, instead of
simply updating the ready queues and the bitmask, also cache what that
thread is, so that when the scheduler is invoked, it can simply fetch it
from there. This is only done if there is a thread in the cache, since
the way the cache is updated is by comparing the priorities of the
thread being added and the cached thread.
When a thread is removed from the ready queue, if it is currently the
cached thread, it is also removed from the cache. The cache is not
updated at this time, since this would be a preemptive fetching that
could be overriden before the newly cached thread would even be
scheduled in.
Finally, when a thread is scheduled in, it now becomes the cached thread
since the fact that it is running means that by definition it was the
next one to run.
Doing this can speed up considerably some context switch times,
especially when a thread is preempted by an interrupt and the same
thread is scheduled when the interrupt exits.
Change-Id: I6dc8391cfca566699bb9b217eafe6bc6a063c8bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The unified kernel calls a function (_get_next_ready_thread) to fetch
the next thread to run: it thus must save caller-saved registers that
are expected to hold a value before calling such function.
The callee-saved registers are available after saving them in the
outgoing thread's stack, so use some of those instead to reduce the
number of registers to save before calling _get_next_ready_thread. Also,
save caller-saved registers in callee-saved registers instead of on the
stack to reduce memory accesses.
This issue did not show up previously, probably because
_get_next_ready_thread did not use the regsiters that had to be saved,
but an upcoming optimization to that function stomps on them.
Change-Id: I27dcededace846e623c3870d907f0d4c464173bf
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The code density registers are NOT saved on the stack.
This is controlled by bit 13 in AUX_IRQ_CTRL, which didn't even have a symbol
defined for it. I've also added _ARC_V2_AUX_IRQ_CTRL_LP for bit 13.
Change-Id: Ie80853b72bed4e60a5cf1cf0a8c905a3d86180d9
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
In order to add the EM7D SOC, I will be implementing a version of the FIRQ
interrupt handler that saves and restores registers on the stack when
RGF_NUM_BANKS==1. All other ARC SOCs at this time have RGF_NUM_BANKS==2,
allowing for a faster handler that can use the registers in the 2nd register bank.
But EM7D doesn't have this 2nd bank, hence the need for this new configurable choice.
(See ZEP-966)
Change-Id: Ie089f1f079902552cf279c2cda23ee0805b01eed
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Using AON for GPIO kconfigs is very specifc to quark se, there
is no need to make this special for this platform. Use the
existing scheme instead.
Change-Id: I946431490380dc0f537d6056277a94c9c9c80fed
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Not used anymore as the support for dynamic IRQs was removed by
commit 844e212.
Change-Id: I624bbd777b2dbcbf905cedc61e63cef21e8a0bce
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Move SRAM_BASE_ADDRESS and FLASH_BASE_ADDRESS to Kconfig.soc since
it will most likely be the same values for all STM32 socs.
Change-Id: I682dc441e34155a19a4f90757707008ef299e9d4
Signed-off-by: Fabien Parent <fparent@baylibre.com>
i2c_quark_se_ss driver is deprecated and replaced
by i2c_qmsi_ss. So remove i2c_quark_se_ss definition.
Change-Id: Idcc6a7f01ffae626ae7d5f9966eac67be78599af
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
