Differentiate call to ll_adv_params_set, whether used by
legacy LE Set Advertising Parameters or LE Set Extended
Advertising Parameters.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Enable Advertising Extensions features in the controller
when enabled in the Host in combined host+controller based
applications.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Update implementation of periodic advertiser's LLL to
correctly handle event counter values when latencies
introduced due to sync events cancelled by active events
operating in unreserved time space.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Update implementation of master and slave LLL's to correctly
handle event counter values when latencies introduced due to
connection events cancelled by active events operating in
unreserved time space.
When an active radio event extends into unreserved time
space, and a connection event prepare is scheduled but at
the time of pre-emption timeout if the connection event is
cancelled then the event count and latencies needs to be
continiued to get acummulated.
In the current controller usecases the above scenarios does
not get exercised, the changes in this commit is needed for
future roles that can extend into unreserved time space and
would cancel a scheduled connection event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix conditional compilation of advertising extensions and
periodic advertising do that platforms with not support in
their LLL can be built without advertising extensions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix conditional compilation of piggy back implementation.
This code should be deleted once periodic advertising
implementation is complete.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor to reuse common repeated code in ISR that reset
status, and performed abort, done and cleanup.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add implementation to support ADV_EXT_IND PDU with AuxPtr.
Changes in this commit only prepares the ADV_EXT_IND PDU
in the primary channel.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Updated the shell commands related to Advertising Extensions
to call the LE Set Extended Advertising Data command
functional interface for testing purposes.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added debug information print outs in HCI code related to
Advertising Extensions events.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add support for Bluetooth Controller GPIO Debug Pins for
nRF5340 PDK board. GPIO Pin toggling can be captured on the
P3 pinhead of the PDK.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Previous mode store function only can store single data,
change this to store as KV model, let's app-layer to manager
model data, other than by stack when node reset.
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Port advanced scheduling implementation from legacy
controller.
This implementation schedules
- non-overlapping scan window when there are simulataneous
central connections active
- central connection establishment with similar connection
intervals be placed in a non-overlapping group, temporally
- connection parameter request with calculated window offset
hints to have non-overlapping BLE radio events.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add a function to reset the variable holding the connection
context of the currently active Connection Parameter Request
Procedure.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Address the nRF5340 Engineering A Errata 16, RADIO: POWER
register is not functional.
This affects the dependency of controller's HAL
implementation that expected correct reset values being
set in the Radio peripheral.
As the SUBSCRIBE_TXEN and SUBSCRIBE_RXEN where not in their
reset value, Radio transmission and reception start using
DPPI was broken.
Fixes#25942.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The bt_l2cap_le_conn_rsp struct in l2cap_internal.h has not been
declared __packed. This can cause alignment problems on some
platforms if the struct is placed on an unaligned address.
A __packed declaration solves this issue by forcing the compiler to
use store instructions that do not required alignment.
Signed-off-by: Jim Luther <jilu@oticon.com>
Implemented an intermediate decrypt buffer to cover the CCM
overrun under CRC error conditions. The workaround is
applicable to nRF52832 SoC only, which is missing the
MAXPACKETSIZE register in the NRF_CCM peripheral.
Fixes#21107 for nRF52832 SoC.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Adds propagation of error returns from the model init callbacks in
Access, and removing any other checks for successful init in the
foundation models.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Fix missing assignment of NRF_CCM->MAXPACKETSIZE register
for PDU sizes smaller than 251 bytes. If there is CRC errors
causing PDU length fields to be higher than configured PDU
buffer sizes in the controller, without the MAXPACKETSIZE
register set to correct PDU size, CCM module could overrun
the PDU buffer and cause memory corruption. This fix is
applicable for all nRF52 Series SoCs except nRF52832 SoC.
Fixes#21107.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
After removal of legacy controller ll_adv_aux.h does not exist anymore.
This is fixed in this PR by including ull_adv_aux.h instead.
The error only shows up when Advertisement Extensions are enabled
in the LL (CONFIG_BT_CTLR_ADV_EXT=y)
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
CC: mesh/access.c
mesh/access.c: In function 'model_has_dst':
mesh/access.c:483:10:
warning: returning 'u16_t *' {aka 'short unsigned int *'} from
a function with return type '_Bool8' {aka 'unsigned char'} makes
integer from pointer without a cast [-Wint-conversion]
483 | return bt_mesh_model_find_group(&mod, dst);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: chao an <anchao@xiaomi.com>
The existing feature exchange procedure does not give the proper
response as specified in the BT core spec 5.0.
The old behaviour is that the feature-response returns the logical and
of the features for both peers.
The behaviour implemented here is that the feature-response returns the
featureset of the peer, except for octet 0 which is the logical and of
the supported features.
Tested by using the bt shell, and having different featuresets
on the 2 peers.
This fixes#25483
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Some Kconfig defined devices may be defined using dt_chosen_label
function. Since there is no way to ensure a device enabled in dts
is also defined in Kconfig, it may happen that instance is not
actually defined.
In this case device_get_binding might return 0, leading to undefined
behavior in the function that calls it.
When not already done, systematically check return of function
device_get_binding on devices defined through dt_chosen_label macro.
Trigger ASSERT when required and return error when possible.
Fixes#20068
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commits fixes the loading of bt/cf settings into memory. Only data
was loaded and not the address.
Signed-off-by: François Delawarde <fnde@demant.com>
build breakage if SMP is disabled
In function `bt_unpair':
bluetooth/host/hci_core.c:2640: undefined reference to `bt_foreach_bond'
Signed-off-by: chao an <anchao@xiaomi.com>
The transport segmented TX nack and seg_pending fields must be at least
6 bits to avoid overflow for 32 segment messages. This change rearranges
the seg_tx fields to gather all state flag fields in one byte, while
making the counter fields whole bytes.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Fix missing transmit buffer demutiplexing before checking if
slave latency needs to be maintained or cancelled.
This bug was detected when new transmit buffer was enqueued
overlapping with on-air radio transmission of empty PDU
preceding the handling of radio event done.
Symptoms of this bug being data transmission latency of upto
slave latency plus one times connection interval.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Increases the transport segmentented tx seg_o counter to 6 bits to avoid
overflow when sending 32 segments. The check in the send loop would
previously never be false, which causes segments to repeat
unnecessarily.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Fixes bug where the transport segmented tx would decrement the attempt
counter every time it ran out of buffers. If transport ran out of
buffers 4 times before the sending could complete, the transfer would
end prematurely.
Moves the attempt decrement to only execute when all segments have been
sent.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Ensures that friend messages are enqueued, even if the packet is
received with an appkey is unknown to the friend. Previously, sdu_recv
would return EINVAL if the appkey was unknown, which would prevent the
lower transport layer from adding the packet to the friend queue. This
is irrelevant for the logic in lower transport, and should not be
returned as an error.
Fixes#24014.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
If LE Read PHY fails the code was still trying to parse the buffer as a
valid response.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix extended advertiser not using correct set random address command
to set private (NRPA) address when privacy feature has been disabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix Service Changed configuration stored in flash not deleted in flash
when calling bt_gatt_clear from bt_unpair.
When clearing the check for "is bonded" should not be made. If the
bond information is already removed this check will fail.
When clearing the check for "modified" should not be made, clearing
is in itself a modification, and should always be made.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix CCC cfg not cleared when overwriting oldest bond. Calling
bt_unpair with a pointer to the key will result in the key addr being
memset to zero and bt_gatt_clear is called with an zero-set address.
This happens because unpair (hci_core.c) calls bt_keys_clear before
calling bt_gatt_clear.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
get_phy is referenced by BT_EXT_ADV only when BT_OBSERVER is also
selected. Avoid defined-but-not-used warnings in that situation.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit adds support for bluetooth in nRF52820 SoC.
Bluetooth radio related files created and added to Zephyr.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
When using extended advertising the connection can be established on
different PHY. In order to have an updated value of the current PHY
we need to read the PHY of the connection in the connection complete
event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add application control of initiating phy change procedure and it's
parameters.
The reasons for allowing the application control over the PHY:
- Allow changing to Coded PHY.
- Application may change PHY to react to changes in environment
to balance throughput and range.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add application control of initiating data length procedure and it's
parameters.
The reasons for allowing the application control over the data length:
- Bandwidth control adjusted based on number of active connections.
- Changing data length before switching to coded phy.
- Applying workarounds for interoperability problems.
- Controlling order of ATT MTU and data length procedures.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add Kconfig option so that the application can disable automatic
initiation of the data length procedure. This is symmetric with the
PHY auto initiation kconfig option.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Refactor setting the maximum data length parameters supported on in
auto data length procedure. This makes setting the data length of the
connection a re-usable function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
With BT_CTLR_USER_TICKER_ID_RANGE it is possible for vendors to add a
number of ticker nodes for proprietary purposes. The feature depends on
BT_CTLR_USER_EXT.
Signed-off-by: Morten Priess <mtpr@oticon.com>
The numbers should have been the sum of HCI commands count and ACL TX
buffers but instead the buffer size was used which makes the pool holds
substatially more buffer than necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add control over the use name option to advertise shell parameters as
an optional argument.
The argument count for extended advertise parameters had not been
updated for the maximum directed advertise parameter count.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Implement the BT_LE_ADV_OPT_USE_NAME when using bt_le_ext_adv_* APIs
to start the advertiser.
When starting an extended connectable advertiser the name must be
included in the advertising data, since scan response data is
not allowed in this configuration.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove setting state flags in bt_le_adv_start_ext since they are set
by le_ext_adv_param_set, except for BT_ADV_PERSIST flag.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Only persist advertising when the bt_le_adv_start API is used to start
the advertiser. For multiple advertising set a connectable advertiser
can only be started if there is a connection object available for the
advertiser. Leave the decision on which advertising set should be
advertising up to the application instead of suspending advertising
when no connection object is available.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove the BT_LE_CONN_OPT_2M option and update documentation.
This was a misunderstand about the init PHY HCI parameter.
The init PHY in the extended connection create command does not
determine which PHYs are accepted as the initial PHY of the
connection. This is instead determined by the secondary PHY of the
extended advertiser.
The init PHY parameter only specifies which conn parameters are
provided, and since we only provide one conn parameter this option
has no effect.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The last parameter to hci_cmd_done() is expected to be a valid net_buf
since the function immediately tries to dereference it. Fix this by
passing the appropriate buffer reference to the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a new flag to track if the L2CAP channel is pending waiting
for encryption to be changed to resume connecting.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for ATT_MULTIPLE_HANDLE_VALUE_NTF,
ATT_READ_MULTIPLE_VARIABLE_REQ and ATT_READ_MULTIPLE_VARIABLE_RSP.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for EATT bearer which was introduced in 5.2, they work
as extra channels to have GATT traffic, at the moment it is completely
transparent to application when they are in use since the allocation
happens automatically.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds the definitions for Enhanced ATT along with new PDUs and UUIDs
introduced in 5.2.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a callback to indicate when the stack has released all
references to a given channel so the owner free up any resources
associated with that.
This is requires since EATT channels cannot rely on the destroy callback
as it does not use a fixed channel like ATT.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This leaves only channels on the dynamic range to be offloaded to the
system queue so ATT and EATT handling are handling in the same context.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds the initial implementation of ECRED mode which can connect up
to 5 channels simultaneously and is required by EATT.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This introduces new Enhanced Credit Based Flow Control PDUs and related
definitions which were introduced in 5.2.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Split BT_CTLR_CONN_RSSI option into two, the base option enables the
Read RSSI command, while the new BT_CTLR_CONN_RSSI_EVENT enables the
connection RSSI events. There is no handling of RSSI events, only a
BT_INFO log.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The bluetooth subsystem is now fully compatible with the new timeout
API, so remove the selection of the legacy API.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert bluetooth mesh to using k_timeout struct. Many of the mesh
modules uses timeout calculations, so it is most practical to keep
the s32_t type and only initialize a k_timeout_t struct when
calling the kernel.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert bluetooth host to using k_timeout_struct for the timeout values.
This is mostly replacing s32_t with k_timeout_t.
In l2cap the handling of no timeout in send channel request was removed
since the timeout is both documented as minimum of 1 second and never
given any no timeout value.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert bluetooth controller to using the new k_timeout_t API so that
CONFIG_LEGACY_TIMEOUT_API can be turned off.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove logging of individual threads spread out throughout the
bluetooth subsystem. The stacks can be analysed by enabling the
following options.
CONFIG_THREAD_ANALYZER=y
CONFIG_THREAD_ANALYZER_AUTO=y
CONFIG_THREAD_ANALYZER_RUN_UNLOCKED=y
Optional:
CONFIG_THREAD_NAME=y
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Include the RPA addresses in the enhanced connection complete debug
log. This makes it easier to debug privacy failures.
Use a new debug statement so that the debug print will work correctly
when log_strdup does not copy the string.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix local RPA field for the legacy controller. This failed without
compilation errors because of blind pointer cast between two
structs of similar definition.
Set the local RPA field of the enhanced connection complete event only
when the address was generated by the controller. If the host has
set an RPA and this one was used the controller should return all
zeroes.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Set the local RPA field of the enhanced connection complete event only
when the address was generated by the controller. If the host has
set an RPA and this one was used the controller should return all
zeroes.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix compilation issue for extended advertising beacon. Adv pool was
mistakenly put under BT_OBSERVER define.
Both observer and broadcaster use the bt_lookup_id_addr. SMP cannot
be enabled without connections, so for broadcaster and observer there
will not be a lookup.
Fix compilation warning for extended scanner-only build.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
According to the BT Core spec. The local RPA field in the enhanced
connection complete event should be set if the own-address type was
set to 0x02/0x03 and the controller generated an RPA using a non-zero
IRK, otherwise the controller should return all zeroes.
In the case where we generate the RPA in the host instead we need to
handle set the on-air RPA address based on the random address set by
the host.
If this is not handled then pairing will fail because the on-air
addresses are used as input to the pairing procedure.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove handling of extended advertising from connection complete
event. If extended advertising has been enabled and is supported by
the controller then enhanced connection complete must be supported.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This is a rework for OpenISA SW LL of
"b7220cef86 Bluetooth: controller: split: Fix densely scheduled event
preemption"
Fix LLL implementation handling preemption of currently
active radio event with densely scheduled events in the
pipeline.
Preempt timeout was stopped without consideration to there
being more queued events in the pipeline. Also, added
chaining of preemption timeouts one after the other expiry
so as to preempt currently active events by the densely
scheduled events in the pipeline.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
This is a rework for OpenISA SW LL of
"b0826a7f65 Bluetooth: controller: split: Reduce time to setup tIFS
switch"
Refactor to reduce the setup next tIFS switch within tIFS
period of the Radio ISR.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
This is a rework for OpenISA SW LL of
"4547bfb452 Bluetooth: controller: split: handle latency for cancelled
conn events" as well as subsequent fixes
Update implementation of master and slave LLL's to correctly
handle event counter values when latencies introduced due to
connection events cancelled by active events operating in
unreserved time space.
When an active radio event extends into unreserved time
space, and a connection event prepare is scheduled but at
the time of pre-emption timeout if the connection event is
cancelled then the event count and latencies needs to be
continiued to get acummulated.
In the current controller usecases the above scenarios does
not get exercised, the changes in this commit is needed for
future roles that can extend into unreserved time space and
would cancel a scheduled connection event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
This is a rework for OpenISA SW LL of
"62c1e1a52b Bluetooth: controller: split: Fix assert on invalid packet
sequence"
Fix to remove assertion failure check on detecting invalid
packet sequence used by peer central and that no non-empty
packet was transmitted.
Fixes#22967.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
User of bt_buf_get_rx may attempt to push their own headers, e.g. ACL
headers, so move the H4 header logic to bt_recv after logging into the
monitor since otherwise the buffer would contain H4 headers which is
not expected by the monitor.
Fixes#24646
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
According Mesh Profile 1.0.1. A application key shall
binding single network key. And Device key shall bind all
network key, and dev key only known by cfg_cli and node self,
only used by cfg_cli & cfg_srv.
Fixes: #21088
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Fixes bug where the config client's net_key_status handler would attempt
to pull two key indexes from a message which only holds one.
Fixes#24601.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
After #22013, bt_le_adv_param got additional fields which were passed to
the bluetooth API uninitialized in the BT Mesh module. This
zero-initializes the entire structure in all usages to avoid passing
uninitialized data now and in the future.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Add support for multiple advertising set. Move the advertising state
flags to be per advertising set and loop over advertising sets instead
of looking up legacy advertiser set or handle 0.
Since it is not certain that the advertising set terminated event can
arrive directly after the connection complete event there is currently
a limitation that there can only be one local identity used by
connectable advertisers at a time. This guarantees that we know
the local identity being used in the connection complete event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Only attempt to restart the background scanner in connection complete
event when the new connection is a master role connection or the
initiator was successfully canceled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Enable enhanced connection complete when extended advertising has been
enabled. This event is mandatory if extended advertising is supported.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This makes hci_raw to manage RX and TX buffers so its logic don't have
to be replicated on each an every driver/application, it also makes it
simpler to deal with extra headers for H:4 mode since that then can be
done at earlier at buffer allocation.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for registering a command extention table which is
used to match incoming commands and then pass the buffer to its
function handler.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds 2 config options which enables hci_raw to work in
H:4 mode and enable it by default automatically.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds USB_PID_BLE_HCI_H4_SAMPLE along with it driver which uses H4
over bulk endpoints.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When legacy advertising enable command is issues,
the BT_ADV_ADVERTISING has to be set, because this
flag is checked in many scenarios to see if the
advertising is ongoing or not.
Signed-off-by: Ahmed Shokry <ahmed.shokry@synopsys.com>
When receiving an unknown command send the unknown command response
as a command status event instead of a command complete event.
A command complete event has no status field, although by convention
all command parameters has a status field as the first parameter the
command status event seems like the more fitting option.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add option for low power node automatically subscribe
all-nodes-address to friend sub list.
Fixes: #24009
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Give NULL pointer when ad_len or sd_len is zero, this stops the host
from setting a zero length advertise data or scan response.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix the advertise command not setting the peer address parameter to
NULL, this could turn it into a directed advertiser.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This patch adds the selection of the necessary CONFIG_*
options for allowing the use of privacy on VEGA platform
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
The radio on the VEGA platform will now be able to resolve Resolvable
Private Addresses through the use of the CAUv3 hardware. With this
patch the RPA feature is now fully supported on the Controller:
RPA addresses are generated with local IRK and resolved with
previously exchanged peer IRK.
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
When disconnecting att_reset is called and all requests are notified
but instead of passing req->user_data like it should it pass the req
itself which nowdays comes from a k_mem_slab, rather than being a
contiguous memory that would contain the request and its user data,
which would likely cause invalid access.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add shell options to configure an extended advertiser for directed
advertising.
Add shell options to provide arbitrary advertising data as well as
giving scan response data.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This patch introduces two major changes to the directed advertising
feature of the bluetooth host.
Deprecating the bt_conn_create_slave_le, and removing
bt_conn_le_create_slave which has never been released. This behaviour
has now been moved by to providing the peer direct address into the
advertising parameters.
Introducing directed advertising support for nonconnectable
directed extended advertising, both scannable and non-scannable.
A bug was also fixed in the the directed-adv command in the shell
when the argument "low" was given. The advertiseng parameter pointer
declared with BT_LE_ADV_CONN_DIR_LOW_DUTY was declared in a scope that
was no longer valid when it was used to start the advertiser.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Makes a common link_closed function for PB-GATT, getting rid of a bug
where cb_data is reset before the link closed callback. Also ensures
that the link close and reset order is the same in both scenarios.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The LE Connection Complete HCI event, unlike its Enhanced counterpart,
only uses 0x0 and 0x1 for Peer Address Type. Fix it so that it reflects
the specification correctly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This PR fixes#23482. The preamble size for a 2M phy was incorrect.
There is a bug in calculation of time for the DLE procedure:
the preamble size is incorrect for the 2M phy
Fixes#23482
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
When PB-GATT Procedure timeout, func `bt_mesh_pb_gatt_close`
will also dumplicated with `link_closed()`
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Check the return value of LE Set Extended Advertising Parameters
command when starting an advertiser from bt_le_adv_start with
CONFIG_BT_EXT_ADV enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The LE Set Extended Advertising Set Random Address command may be
issued at any time after an advertising set identified by
the Advertising Handle parameter has been created using the
LE Set Extended Advertising Parameters command.
This commit fixes the advertising set issueing the set random address
command before the advertising set is created in the controller.
Since the le_adv_set_random_addr function has is used to get the the
own address parameter for the it could not simply be moved, and
moving the own address parameter handling out of this function
would create a potentioal maintaince problem.
Also this function is used for both with and without advertising
extension feature so changing it is not trivial without breaking all
the previous random address handling already put in place.
The simplest solution was therefore to postpone the command until the
parameters has been set using 2 flags.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use bluetooth assert on HCI command send error since this assertion is
always enabled and we should not continue after this has failed.
Log command status failure with information in order to make it more
visible as the HCI status code is more interesting than the -EIO error
code returned by the function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add BT_ASSERT_MSG assert mechanism that can print assertion messages
when verbose bluetooth asserts are enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix seg_tx occupy when no segment not send
and allocate rx_seg when receive such message.
Fixes: #24101
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
For the ll code we know the exact entropy device as its the one for the
SoC that we are on. So use the new DT macro's to get the entropy device
via DT_INST rather than using CONFIG_ENTROPY_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the pending slave set connection latency and timeout values not used
in the connection update procedure when
CONFIG_BT_GAP_PERIPHERAL_PREF_PARAMS has not been enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The board target for emulation of nRF52810 on nRF5DK, so far
known as nrf52810_pca10040, is renamed to nrf52dk_nrf52810.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Extends the bt_conn_le_create_param struct to provide the option
to set a custom timeout for the initiation of the connection.
The logic for the default values of window_coded and interval_coded
were moved to conn.c in order to resolve all defaults for the
create_param struct at a single location.
Timeout is not added as a parameter to the BT_CONN_LE_CREATE_PARAM
macro due to the expectation that CONFIG_BT_CREATE_CONN_TIMEOUT
will be the typical value that users will expect.
Fixes#23468
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Fixed overflow risk when `poll_timeout` is 1s,
although it is not recommended to use it like this,
when it is used like this, `POLL_TIMEOUT_MAX`
will overflow.
When the poll timeout set like above, the default `6`
req_attemps for first pull request lost,
may cause this procedure bigger than poll_timeout,
Well, stop scanning when lpn terminated friendship,
this will save lots of energy, when lpn mode enable,
the scanning will be start after `FRIEND_REQ_RETRY_TIMEOUT`
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Fix an an issue where established bonding information in the peripheral
are deleted when the central does not have the bond information.
This could be because the central has removed the bond information, or
this is in fact not the central but someone spoofing it's identity, or
an accidental RPA match.
This is a regression from: a3e89e84a8
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The net_buf subsystem is now fully compatible with the new timeout
API, so move the selection of the legacy API to those specific
subsystems that use net_buf and still need converting.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Update implementation of master and slave LLL's to correctly
handle event counter values when latencies introduced due to
connection events cancelled by active events operating in
unreserved time space.
When an active radio event extends into unreserved time
space, and a connection event prepare is scheduled but at
the time of pre-emption timeout if the connection event is
cancelled then the event count and latencies needs to be
continiued to get acummulated.
In the current controller usecases the above scenarios does
not get exercised, the changes in this commit is needed for
future roles that can extend into unreserved time space and
would cancel a scheduled connection event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add additional build configurations to the shell to catch build errors
when enabling extended advertising.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix compilation issue when extended advertising is enabled but privacy
is disabled. In this case the rpa_update work is compiled out.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Run the int_literal_to_timeout Coccinelle script to fix places where
it is clear that an integer duration is being passed where a timeout
value is required.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Most places used an int so that should have handled most cases but
keys_set was using an unsigned int, which meant that checking len > 0
is an expression that is always false, and the error handling is not
working.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The publication context is checked for NULL in bt_mesh_model_publish()
however it was dereferenced before that. Move the assignment to
ctx.send_rel to the same place where other ctx members are set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix regression in cancelling slave latency during Connection
Update Procedure.
Slave latency should not be applied between the ack of a
Connection Update Indication PDU and until the instant.
When caching was introduced, implementation missed this
consideration.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Ticker is now fixed to avoid catch up of periodic timeout under
large ISR latencies.
Revert commit a749e28d98 ("Bluetooth: controller: split:
nRF: Use ticker compat mode as default").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If must_expire is set for a ticker instance, then ticker
expiry shall still perform catchup.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Reset ticker state in ticker_job for ticker instances that
have been skipped in the ticker_worker.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix ticker to avoid catch up of periodic timeouts in case of
large ISR latencies like in case of flash erase scenarios.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix regression in cancelling slave latency during Connection
Update Procedure.
Slave latency should not be applied between the ack of a
Connection Update Indication PDU and until the instant.
When caching was introduced, implementation missed this
consideration.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Simplify the Data Length Update Procedure state check when
processing incoming LENGTH_REQ/RSP PDUs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Simplify the Data Length Update Procedure state check when
processing incoming LENGTH_REQ/RSP PDUs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add validation of channel map and hop increment value
received in CONNECT_IND PDU.
Zero bit count leads to controller assert or divide-by-zero
fault.
Hop increment shall be between 5 and 16 by BT Specification.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add validation of channel map and hop increment value
received in CONNECT_IND PDU.
Zero bit count leads to controller assert or divide-by-zero
fault.
Hop increment shall be between 5 and 16 by BT Specification.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix high-duty cycle directed advertising when extended advertising
feature has been enabled. The duration parameter when starting extended
high duty cycle directed advertising has to be set to a non-zero value
less than or equal to 1.28 seconds.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Avoid removing identity keys from the controller during the pairing
procedure. During the pairing procedure the keys will be cleared before
they are updated. This causes an unnecessary warning from HCI core where
it tries to remove an IRK key-set from the controller that has has not
been added yet.
While this is not an issue, the warning from HCI core is misleading and
might lead to unnecessary questions and investigations.
Warning appeared after: 6c6bd8c49e
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the pending ID keys add and delete flag out of keys storage area.
These flags are runtime flags and should not be stored in persistent
storage.
Due to struct alignment storage start has to be aligned so that
variables added before storage start does not affect the storage bytes
by introducing padding in the storage area
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Add shell advertise set info get command to print advertiser set local
identity and TX power selected by the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Skip feature testing of controller features when legacy advertising
commands are not supported. For combined builds or builds where the
capability of the controller is known it is not required to have runtime
check of controller extended advertising support.
This gives the following size reduction for hci_core.c:
Without legacy support
hci_core.c 19980 7.75%
total 257679
With legacy support
hci_core.c 21816 8.41%
total 259519
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Handle updating the identity keys in the controller while a scanner
limited by timeout or advertiser limited by number of events or timeout
is active in the controller. For this case we mark they keys as pending
and handle the update of the resolving list ones the roles are stopped.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add RPA handling for scan limited by timeout. The scan limited by
timeout has no information about elapsed time when stopped. So pausing
the scan at RPA timeout has no new scan timeout value to set.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add shell command to retrieve advertising set OOB information for the
selected advertising set.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add error code to API for starting directed advertiser. Also rename the
API in order to follow the established naming pattern.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add advertising sent connected and scanned callback and print the
information available.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add shell arguments to control scanning phys for scanner and initiator.
This allows to scan on coded or create connections on coded.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add scan recv callback and print extended scan information available.
Add scan timeout callback to print when scanner has stopped.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Print the error codes in hex so that it is easier to lookup, error
codes are usually given as hex.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support for creating and advertising with an advertising set.
This has support to advertise with extended data and with long range
feature on Coded PHY.
Limited to only supported one advertising set.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support to use the extended conn create options to establish
connections on LE Coded PHY or 2M. This uses the connection options
set by bt_conn_set_scan_params.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add API to set the scan parameters used in the LE Create Connection
HCI command used by bt_conn_create_le and bt_conn_create_aute_le.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support for the new scan options and use the LE Extended Scan
HCI commands if they are available in the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Refactor scan and initiator random address handling to a helper function
so that it can be re-used.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add reference count old to new value transition in the debug print, this
makes it easier to interpret the printed line when debuggin reference
count bugs.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Extract setting advertising filter policy parameter from the adv params
options field to a helper function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
