Turn the GATT notify multiple feature off as default value.
This feature changes the behavior of the bt_gatt_notify API in a way
that might not be backwards-compatible.
This is because the notify multiple header is larger, and therefore
limits the amount of bytes that could otherwise have been sent in a
normal notify PDU for a given ATT MTU.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix use of conn_handle in LE Advertising Set Terminated event not
converting from serial Little Endian to native CPU endianness.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use an unspecified reason when disconnecting a connection that did not
have a pending connection in the host.
We don't allocate connection objects in the connection complete anymore
so using memory-capacity-exceeded is misleading.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This patch fixes an issue with the advertiser not resuming connectable
advertiser if the last bt_conn_unref happens from something other
than the disconnected callback.
In this case this last bt_conn_unref was from gatt.c notify_cb called
from application main thread.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix host RX thread being deadlocked. The deadlock occurs because the
RX thread is stuck waiting in conn_tx_alloc with K_FOREVER but if the
connection is disconnected only the RX thread can unblock it in the
handling of the disconnect event.
This commit fixes this deadlock by splitting the processing of the
disconnected event into two parts.
The part needed to unblock the RX is to release resources held by
unack'ed TX packets and mark the connection state as not connected
anymore.
The RX thread waiting for free_tx fifo and the TX thread waiting for
the bt_dev.le.pkts semaphore will both check the connected state after
having acquired them and will abort if disconnected.
The rest of the processing will be handled at normal RX thread
priority like normal.
Move the bt_recv_prio handling to the Bluetooth host when the host
has defined its own RX thread (CONFIG_BT_RECV_IS_RX_THREAD=n).
If the HCI driver has the RX thread (CONFIG_BT_RECV_IS_RX_THREAD=y),
then the responsibility to call bt_recv and bt_recv_prio correctly
falls to the HCI driver.
The helper function bt_hci_evt_is_prio() is replaced with
bt_hci_evt_get_flags() so that the HCI driver can do this correctly.
This decision to replace was made so that existing HCI drivers
maintained out-of-tree will fail at compile time with the new system.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bluetooth: host: Move bt_recv_prio to host when RX thread is defined
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Save link key to settings_subsys, no need to re-pair after restart.
Overwrite old pairing records with aging counts.
Signed-off-by: ZhongYao Luo <LuoZhongYao@gmail.com>
The hci-cmd currently accepts only a 1 byte parameter. This
disables use of commands that requires more than 1 byte,
for ex. the feature exchange that requires a 16 bit parameter.
This commit allows a datafield parameter up to 65 bytes long.
65 bytes comes from the nr. of parameters for the
HCI_LE_Generate_DHKey command
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Friend Request is also transmitted over local queue and
if both Friend and LPN features are enabled then we would
try to establish friendship with ourselves.
Fixes MESH/NODE/FRND/LPN testcases.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
The hardcoded value was arbitrary and interfered with message cache
mechanism causing invalid behavior and PTS test to fail.
Fixes MESH/NODE/RLY/BV-02-C.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
According to Mesh Profile Test Specification we should still
relay messages with DST address that is RFU.
Fixes MESH/NODE/RLY/BV-01-C.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Key refresh procedure was ignored on non-primary subnet.
Mesh Profile Specification v1.0.1:
3.10.4 Key Refresh procedure
"This procedure is used when the security of one or more network
keys and/or one or more of the application keys has been compromised
or could be compromised."
"It is possible to update each NetKey independently of all other
NetKeys. A Key Refresh procedure for one NetKey can be in a different
phase to another Key Refresh procedure for other NetKeys."
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Reset provisioning bearers when bt_mesh_reset() is called. Accept
another provisioning attempt after link close.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
This value was used quite often in the file so adding a
descriptive name should improve readability.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
The comparison of a current tx link transaction id caused
us to not send ack and in effect fail provisioning.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Fix the advertise object not release when a high-duty cycle directed
advertiser timeout happens. If the extended advertising feature has been
enabled in the host, but not supported by the controller then the
advertising object must be released in the connection complete event
since there will not be a advertising set terminated event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix issue with directed advertiser not accepting connection request
from non-privacy enabled peer that has given us a non-zero IRK.
When device privacy is enabled then ull_filter_lll_rl_addr_allowed will
return true, and update the rl_idx to entry in the resolving list.
When the directed advertiser is not privacy enabled then lll->rl_idx is
set to FILTER_IDX_NONE and will not use RPA for the target address.
The check rl_idx != lll->rl_idx will then fail (0 != 0xff) and the
connect request is denied, even though all addresses matches on-air.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Removes the memset of the prov_bearer_cb in PB-GATT during resets. This
allows the provisioning link to disconnect and reconnect again without
having to call pb_gatt_open.
Fixes#26343.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Add explicit opcode check when handling received unknown
response PDU.
Without this, for example, an in progress Data Length Update
procedure state was reset when receiving an unknown response
to slave initiated feature request.
Fixes#26252.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add options for phy update procedure. User can now set no preference
option for a particular PHY as well as preference for LE Coded PHY
coding scheme.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
These functions don't work with buffers that do have fragments, instead
this replaces their usage with net_buf_{put,get}.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
ATT_PENDING_SENT does severely impact the throughput since multiple
packets no longer can be scheduled at same time, so instead of always
setting it regardless of the bearer/channel it is now only used for
EATT since that cannot set its own callbacks.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
bt_l2cap_send_cb may fail if there are no context available which means
that the request would not be sent, also due to the use of custom
callback it cannot be queued either so the only option is to return the
error and let the application handle it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since the TX semaphore is used for all types of PDUs a request may have
to be put on the request list while there is no pending request pending
which means no response will be generated to trigger att_process,
previously this condition was handled by setting the request as
currently pending and append its buffer to tx_queue but this is no
longer efficient since there could be more than one channel active the
code should try all of them before queueing back to request list.
To fix this the request list will now be processed each time a PDU has
been sent.
Fixes#26070
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
ATT channel sent callback shall not be overwritting until the
operation completes as it can result in breaking flow control when
CONFIG_BT_ATT_ENFORCE_FLOW is enabled.
Fixes#25964Fixes#26071
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Disable the controller advertising extension feature default setting
until the feature is complete. The zephyr host requires the
LE Advertising Set Terminated event to function.
Without this event a peripheral connection cannot pair because the
local on-air address is not set, and the advertising state will not be
cleaned up, so advertising cannot be started again.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The frnd->last buffer can potentially be NULL if friend_clear is called
after the adv.c buf->busy check, but before the adv_start callback.
The current design is based on the adv.c thread being cooperative, and
therefore not yielding between the busy check and the adv_start
callback, but as the bt_le_adv_start call has to acquire a semaphore,
there's a possibility for friend_clear being called inbetween.
Fixes#26177.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Add warning about enabling the options below so that users are
aware that this is a security risk.
- CONFIG_BT_DEBUG_SMP
- CONFIG_BT_DEBUG_KEYS
- CONFIG_BT_OOB_DATA_FIXED
- CONFIG_BT_USE_DEBUG_KEYS
- CONFIG_BT_STORE_DEBUG_KEYS
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the NRF RNG entropy device as the entropy device for bt_rand and
controller internal functions when LLL is Nordic.
Using an entropy source with a significant increase in stack usage
will invalidate all stack size configurations in the system and lead
to stack overflow issues.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix compilation regression due to addition of const
qualifier to tx_pwr_lvl parameter of ll_tx_pwr_lvl_set
function. Support for BT_CTLR_TX_PWR_DYNAMIC_CONTROL
needs the tx_pwr_lvl to be updated and returned.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
For some reason GCC 9.x doesn't seem to be able to realize that set_num
will always be > 0 and so the local variable status will always be
initialized. Use a do {} while instead to keep it happy.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix missing implementation of initialization of common
advertising header bit fields when new auxiliary channel PDU
is instantiated. This caused corrupt invalid Bluetooth
Device address being copied from uninitialised previous
auxiliary PDU instead of copying from primary channel PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Review rework, added comments, TODOs, FIXMEs and converted
magic number use in advertising set state flags to defines.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added comments and code to make note that disabling all
advertising sets is not yet implemented.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor pdu.h defined in anticipation of reused in
Advertising Extensions implementation. To reuse in
calculating ticks_slots etc.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix segmentation fault detected by BabbleSim test due to
incorrect number of tickers being allocated.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Avoid ticker from null pointer dereferencing when storing
operation callback functions to be called during collision
resolution.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix scan set allocation using BT_CTLR_SCAN_SET instead of
an incorrect duplicate BT_CTLR_SCAN_MAX.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Integrate the generated extended adv report PDU list into
HCI layer to generate the HCI LE Extended Advertising Report
event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Change the implementation of extended scan PDU rx list to use
the extra pointer as the next field in the linked list node.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix missing Auxiliary PDU when primary PDU is calculating
the offset. Schedule the auxiliary PDU ticker before primary
PDU ticker is scheduled.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the Low Latency Prepare Done that disables ULL_LOW
context executions inside a radio event, so that
ticker_job_idle_get is invoked from ULL_LOW instead of LLL
context so that its enqueued alongwith others scheduled
in ULL_LOW. This is avoid premature disable of ULL_LOW
context executions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When Privacy is not supported in the build and Advertising
Extensions is enabled, HCI LE Enhanced Connection Complete
event was missing. This is fixed now.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix incorrect adv_addr type in auxiliary PDU when address
is removed from primary and added to auxiliary PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added implementation to calculate the window widening for
the reception of auxiliary PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix to avoid a crash due to missing aux_ptr in current
primary PDU constructed by LE Set Extended Advertising
Parameter Set, while aux_ptr was populated by LE Set
Extended Advertising Data Set in the latest double buffered
PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added implementation to handle updates to adv mode and event
properties of an already created advertising set.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix collision resolution to consider single-shot ticker,
current single-shot with ticks_slot as older that a next
periodic or single-shot ticker with ticks_slot.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix ticker to correctly generate the operation callback if
single-shot ticker fails to be scheduled and does not
expire.
As the collision resolution is deferred to the worker, if
a single-shot ticker is cancelled, then appropriately call
the operation callback with failure status. This is allow
the user to take necessary actions, like release resources
allocated that need to be release on the failure to schedule
the single-shot ticker expiry.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Move the definition of PKT_US into pdu.h so that it can be used
by Advertising Extensions implementations too.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove us_radio_rdy field in the footer structure as its always
a constant value which can be obtained using a functional
interface to HAL.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix legacy advertising started using Extended Advertising
sets to use the set advertising random address.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix missing reset of phy struct member for scan set that is
not being enabled by use of LE Extended Scan Parameter Set
command.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Allow use of HCI LE Set Random Address cmd when advertising
is enabled using Extended Advertising commands.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix, use phy variable instead of type to determine if
scanning on Coded PHY is to be enabled.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added implementation to generate LE Extended Advertising
Report for received legacy PDUs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix missing reset of scanner state which could cause a
spurious SCAN_RSP packet without a prior SCAN_REQ being sent
to be reported.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added implementation to support setting of legacy
Advertising Data and Scan Response Data using Extended
Advertising Data set functions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
