PCI enumeration is not mandatory to enable as static information can be
provided. Plus, it does not integrate yet properly with shared IRQ as
well as setting dedicated IOAPIC paremeter for certain drivers.
Change-Id: I221b2a8a2179993a264e5f3eb93cda0e121d9abe
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Providing the right settings through Galileo's Kconfig.
Change-Id: Ia5339eb90cb98d7dde3be0493bcfd9a6b6db60ed
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add Kconfig option to specify how interrupt is triggered for SPI.
Also enabling such support for Galileo platform.
Change-Id: Id3112d100089197940f826b827493174d0f22669
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is specific to Galileo board where its SPI port 0 needs to setup
the CS pin through a GPIO pin.
Change-Id: I9df6f7144a96bcd10f61fc7d057f89caa0e599d1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix previous rebasing errors (before merging) where deleted code
was reintroduced back. This causes the default configuration
in Kconfig to be ignored.
Change-Id: I29b246b1459136521d764127bf02e6d8e5aff30c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This expands the Galileo pinmux driver to configure the GPIOs
on the DesignWare IP block, and the core/resume wells on
the legacy bridge.
Change-Id: Ia1df4b6fd3b104f08563fe9eab93f01efbb53b66
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
If using with shared IRQ, this function will be called by
the shared IRQ driver. So we need to check and bail out
early if the interrupt is not coming from the GPIO
controller.
Change-Id: I4ae925f5fb9a5c32d03a180edc8460e978ec0aac
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
If using with shared IRQ, this function will be called by
the shared IRQ driver. So we need to check and bail out
early if the interrupt is not coming from the I2C controller.
Change-Id: I3c3ae3c22aa5cf312de5c22b35765749d6c5929d
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Such settings belong to Galileo and thus are set in Galileo Kconfig.
Change-Id: Ib9ec721fcc68e92521f8b7690c2640eeb82b2f4c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Call the callback when relevant:
- When STOP_DET if received
- On error
Change-Id: Id60190c6ac5c0b15a0a6cd3fb30b9cc41f2333e8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Handle only the pins which have been configured to be present on this
controller. Removing an unused #define as well.
Change-Id: I66d3638333f1fcd49b1b4f70a5c9d11dbc538fd0
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
On some platforms (e.g. Galileo), the I2C controller is on PCI bus,
which shares IRQ with other devices (GPIO on Galileo). This patch
adds support for utilizing shared IRQ.
Change-Id: Id4e4714aed37c2893d0ffe9ed1e4edaabb338121
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
On some platforms (e.g. Galileo), the GPIO controller is on PCI bus,
which shares IRQ with other devices (I2C on Galileo). This patch
adds support for utilizing shared IRQ.
Change-Id: I4b44bae15356e4710d54f0343fed1bd27f35e484
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds options to the shared IRQ driver so the interrupt
triggering condition can be specified.
For example, the GPIO and I2C controllers are under same
interrupt line through PCI bus. The triggering condition
is level, active-low. So this option can be used by
the Galileo platform to program the IO-APIC correctly.
Change-Id: I1c3af98442e775b4987ab36a644c856052d85ec4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This driver allows multiple drivers to share a common interrupt
line. This functionality is required on system that conform to the PC
interrupt structure. In the context of Zephyr this is needed for
SOC's that have their I/O IP blocks behind a PCI interface. Due to the
limited number of interrupt lines provided by the PCI interface
multiple IP blocks may be configured to share an interrupt line.
Drivers that share interrupts must be modified to *not* register their
own interrupt service routine as part of their configuration/initialization
but instead bind to the correct instance of this driver by name, then
register their interrupt service routine with this driver.
Change-Id: I57b517b97ebeabce484ba53c8f940da993cb391d
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
The polling I2C write function guarantees the write operation
is completed. It is to make sure each write has been commited.
Change-Id: I37cd3b8a65c605837b1fae3ccd1c2b0235c07a37
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The polling I2C write function guarantees the write operation
is completed. Given that the initialization routine goes through
I2C write consecutively, we want to make sure each write
has been committed.
Also adds code to configure the I2C controller before transfer.
Change-Id: I2c8888e940edd1cb9fb01f03234a731ac991dfcf
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This implementation will wait to write, and wait for transfer
to complete before returning from the function. Currently has
a default timeout of 100ms to prevent being stuck in the loop
waiting for hardware to be ready.
Change-Id: I0340fc6fed100f1d31c0306c5b0ab09689364f63
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add I/O port access to MMIO-based GPIO driver, in addition to
the existing direct memory access. This extends the driver,
so that it can address the registers through I/O read/write.
Change-Id: I53c74ad76472ac043764e33bfbb77a2bedc427fe
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The interrupt selectionss are no longer specific to a particular
controller (e.g. I2C_DW_0), but apply to all controllers on
the platform.
[DL: Extracted these changes into their own patch, instead of
being squashed with others. Also modified the Kconfig
options to move them into proper position.]
Change-Id: Idc7ac9769e947447b868dccf772a95dbb5fc8021
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Add a Kconfig option to enable NANO_TIMERS for PCAL9535A.
Without enabling nano timers, compilation may fail.
Change-Id: If96358a17b9522f9323f3480b4716c3dfd82a3de
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The I2C controller should have been already setup before this driver.
Since the only use right now is on Gelileo and I2C_DW driver. it is
safe to remove the i2c_configure() call now as the driver has default
configuration at boot.
Change-Id: Ia384e28871bf76dcfec899860f93da4bf0948ba6
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds the Kconfig option to specify default configuration
for the I2C controller during driver initialization.
During boot, the controller needs to be configured before
communication to slave devices can start. After boot,
an app can re-configure the controller if needed.
Change-Id: I7bf252f75a31943ae444e4d914f3a9a1a3f3d91f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are devices that need are part of the architecture core the need
to be initialized prior to devices that are integrated around a core
to make up a complete SOC. Namely the interrupt controller in the SOC
must be configured in order to allow the integrated IP blocks drivers
to initialize correctly.
Change-Id: I0a91e08f98516a7b7dd402ffc6494a071f1326b2
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
This macro is legacy from an early implementation of the init system
before the pure level was split into early and late phases remove it
now to avoid confusion going forward.
Change-Id: I6720874c840c9e14888fd6f411a8182e7420ca29
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
This provides the API to manipulte the pin muxing, where
a single pin may provide different functions depending on
settings.
[DL: changed commit message.]
Change-Id: Ifd161137c062dff184024b5aa34737604911d09c
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds the driver for PCA9685 I2C-based PWM chip, and provides
basic PWM functionality.
Change-Id: I8c711d9b703fdaf5ccb23657e07495a95cbe16ee
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fixes a build failure in designware gpio driver.
Change-Id: I90a540f56bff17ff56d0315356fde6d6c4d02407
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Register values are now being cached in memory, and are being used in
subsequent writes. This is to avoid reading from registers, as
we know what needs to be written to those registers all the time.
Change-Id: I9b344303c0cb9f28e974514ab674135004f68ea0
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The _has_i2c_master() should return 1 if there is an I2C master.
The logic was incorrectly inverted. So fix it now.
Change-Id: Ic4bf44efc1f68644530a275f0c4e454740a2950a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds the public APIs for PWM drivers. Also, this adds a Kconfig
and an empty makefile for drivers to extend.
Change-Id: I1cc0c908b6f5aeeb678b6368640d5b9a1cc9751d
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Following the naming convention established, private functions
should be prefixed with an _
Change-Id: Ib6006ba3a928da88b8b8c3324f7d4b833f736270
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Many of the i2c functions continue to exist in a format of
<IP>_<interface> and will now follow the <interface>_<IP>_
naming convention.
Change-Id: Ic7ec879105f5c06f0213f8d771b3811253c49658
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Clearing an interrupt in DesignWare is done by reading the port
not by writing to it. Original problem found by Dmitriy@WR.
Change-Id: I1de052632ec36e2d496c563e81307169e9dabcf4
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Those ports uses different instructions to get accessed: in/out
instructions. It differs in many ways with memory access, and it's much
slower. It's unset by default, but some arch exposing legacy UART ports
might need it.
Change-Id: I06f2a7c7812e720863957bd20d5c2b8b02c10734
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The header file was renamed in previous commits, but the #include
referred to a non-existing file. This causes compilation error.
This uses the correct file.
Change-Id: Ibda7dbca82323d99dcff71cbee8f642f6cd611d6
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This makes variables readable and consistent with other drivers
we have.
Change-Id: I816f133279497eafd5d5614013c8d224d5909590
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This driver naming is an exception which compared with all other drivers
we have. To keep things consistent the configuration options and variables
are renamed to <type>_<name>.
Change-Id: Ib95aa09630a507848f78d8f2c28706b545eed06d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Don't give on the semaphore if the ring buffer is full.
Fix a missing newline in a debug message.
Change-Id: Ic0030365665c32cc9f1c641f9dacffd1a1915b09
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some platforms send over \r\n for newlines, just send over the \n.
Change-Id: Ia6072eb3719a4c7dd828457cf1634d16f4eec38a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This adds a simple driver for MMIO-based GPIO ports.
It does not trigger any interrupts due to pin level at this moment.
Change-Id: I0c439f221988817e4be72653c68257ef6ace5bde
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds the driver for I2C-based PCAL9535A GPIO chip.
This currently only enables minimal set of features of the chip for
very simple input/output operations, and does not support interrupt
yet.
Change-Id: I32ea07a71a38866280a96e68cff49cb0df12b85d
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This change puts the DW GPIO Kconfig selections inside GPIO menu.
This also groups all DW GPIO related selections under GPIO_DW.
Change-Id: I776f3f6b89e1a4dc366648f8290abb27de9eceb8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This was missing an include file, which caused the macro to not
be expanded correctly. Including init.h fixes the issue.
Change-Id: I6b190e0c75828d9b6eb42a84c213dfc174510740
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Change the IOAPIC driver to be initialized directly from the init
system. The function signature of _ioapic_init() function is updated
accordingly.
Change-Id: I2f824ac745926966eebb23f60445a41e1df9eb8f
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Change the LOAPIC driver to be initialized directly from the init
system. The function signature of _loapic_init() function is updated
accordingly.
Change-Id: I5ed26d53524c8526d413a05ac9a7a58dd4264c5a
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Change the PIC driver to be initialized by the init system. To be
initialized by the init system the function signature of the
_i8259_init() function needs to be changed to the standard *_init()
function signature specified by the device model.
Change-Id: I63bf1cd0ce78920fa20da94f5966e5aab4bf41b2
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
This introduces a generic driver set for console messages routed over
inter-processor interrupt (IPI) channels. These drivers bind to a
low-level IPI driver instance for the actual transport of messages.
ipi_console_sender installs printk and/or stdout hooks to forward
messages over IPI. There is currently no buffering on the sending side.
ipi_console_receiver installs an IPI callback which stashes incoming
characters into a ring buffer, which is monitored by a nanokernel
fiber. The fiber buffers the characters on a per-line basis and sends
them to either printk or stdout. Multiple instances of this driver
may be created in case you need to receive console data from multiple
CPUs.
Change-Id: Icebc110794fbe040f975101cd2ae6e78fb38645a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We are introducing other kinds of drivers which support a console
that isn't over a UART.
Change-Id: I0dddbdce958437b5709c5ab26252ed47d030413d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The code fragment to bind the instances of the I2C driver is not
platform specific but is driver specific.
All the information required to bind a driver instance comes from
CONFIG_ variables. Having the binding code with the driver code
avoids duplicating the code fragments in each platform where the
driver may be used.
Change-Id: I9ea132c9340437ccb292bb8f3fa3d3a2b2a794db
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
The code fragment to bind the instances of the SPI driveri is not
platform specific but is driver specific.
All the information required to bind a driver instance comes from
CONFIG_ variables. Having the binding code with the driver code
avoids duplicating the code fragments in each platform where the
driver may be used.
Change-Id: Iff40227e3e25d431ae870d585445971f35d934dd
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
The code fragment to bind the instances of the GPIO driver were being
replicated in every platform_config.c This code is not platform
specific but is driver specific.
All the information required to bind a driver instance comes from
CONFIG_ variables. Having the binding code with the driver code
avoids duplicating the code fragments in each platform where the
driver may be used.
Change-Id: Ie07a3d12d25201e82ce7074455e6c036f463851b
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
This buffer can be examined at runtime with a debugger to see what
is going on. Helpful if there are no other working console drivers
on the system.
Change-Id: I759467a57d16204b4b316c4f6fa8b7d5e1d1d236
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When configured as GPIO_ACCESS_BY_PIN, the callback should
be called only if the pin is enabled and received an interrupt.
Change-Id: I7addeb57c8d46dddc027e9b82a92654cd210ade1
Signed-off-by: Ricardo de Almeida Gonzaga <ricardo.gonzaga@intel.com>
The send() callback of HCI drivers should be returning 0 on success
and a negative value on error. The uart_fifo_fill() function returns
the number of transmitted bytes so it can not be directly mapped to
the send() return value.
Change-Id: I59be478c1985f44a46f2a9613f61471423b0e63a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Rewrites the LOAPIC timer tickless idle implementation to cover all edge cases.
Change-Id: Ide0a235f298dfc5c75a090a45d1bf8275d81e248
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removes tickless idle skew calculation as it is not particularly useful.
The actual "skew" may vary wildly depending upon whether cache is involved
or not.
Change-Id: Ie5c966eba5cdc3cff2610d4c1f3bb673c83ec8b7
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Fixes two missed replacements of
_SysIdleElapsedTicks -> _sys_idle_elapsed_ticks
in the timer drivers.
Both were previously missed due to typos.
Change-Id: If55c9624df6f3bd7188e249f74d3ee3de61a68e4
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Make config variable name match the function. The PIC is never turned
on in the zephyr code so there is nothing to shut off.
Change-Id: I1627e5a35cc37ef7959f36758c1e1aec03e22782
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
These x86 drivers are the last users of the PLB_* macros change to use
the sys_{in,out} functions.
Change-Id: Iebd0ad1bf5e74379498f86b24d835a0430db1311
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Or then the controller will spin around requesting to get its fifo
filled-in though it's unnecessary.
Change-Id: I81e7c483345236dee7691c3e780b1b06d6b2d0f8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- Handle the new error callback type, a ROR interrupt is irrecoverable.
- Removing the fifo pre-fill: this should never be done that way. It's
up to the controller to request via an interrupt to get its fifo
filled-in. (TFS bit on SSSR register is the one requesting such
filling)
- Disabling the controller once completed (following transfer will
re-enable it)
- Removing useless debugging info
Change-Id: I466a8efb65a41f3315a6a36e10ea519d0c4b01e9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Change DEBUG option into something more specific.
Change-Id: If1f421fbf7d234ad6bfac410697205d5d74548c0
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Menu depends on X86, however some options are available
for all architectures.
Change-Id: I09cad39811319022d0323a4ff87d415346b5630a
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This will let us getting rid of old outByte/inByte functions.
Change-Id: I3344151c54f99e5e281ac8d3d027e0b810796111
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Only 1 port is available on Quark through the PCI bus.
Change-Id: Ie0e0173686947134d2553dd0fd0230ffa5a1d456
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Since such controller is found on Quark x1000 (Galileo, ...), it will
need to get configured and/or enabled through PCI.
Change-Id: I16d00364edcb17653eaaf073e87b4e5850de7299
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using the OS provided sys-io functions for access to the registers
and lower level devices.
Change-Id: I1a88786189cbed0965f84146ffad9988a3b68a7b
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Initial import of Synopsis DesignWare I2C driver functionality
for the Zephyr Project. This import has been tested for host
master control. While it does contain the code to work as a host
slave, this code has not yet been completely tested and validated.
Change-Id: I3df0214f6e3b6798f7dad4819d09c3ec5998e508
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Adds the necessary changes to Kbuild and Makefiles to enable I2C
driver support to build.
Change-Id: I3113ccbbbbb4e06ef134ca73f509d2755a2abb59
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
- Device ID was wrong
- Setting default class id
Change-Id: I9fd1df284eca4067c21beffa7599307a40be5144
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
A fix for a mistake introduced in commit 1a7357.
Change-Id: I411937c85f29abb934ae5385f4858950f5d76887
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
No need to keep track of PCI class's bus and dev. First, there might be
more than 1 bus and/or 1 device which would hold the same class.
Secondly, with the new PCI_ENUMERATION option, enumeration PCI device is
now optional and it's advised to unset such option and statically
configure the PCI information of the devices (to gain in booting time
and code size). So finally removing all of this.
Change-Id: I395d08c8f6f5e76431af59aa6fc9b30d703f2e75
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Change-Id: I151b3c6516b9b5a38ab0da2948c951eb69d57498
Signed-off-by: Adrian Pochiu <adrianx.pochiu@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The _ARC_V2_IRQ_VECT_BASE register must be set to the vector table in
flash.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Change-Id: Ied5451c98222f545cd669967023aef26c3d8e48e
Only one wrong is sufficient to fail the test: the found device is not
the one we are looking up to.
Change-Id: I2a54b5683fedf7d54de1e1553aecba40b6b6b2e1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will help when debugging, since there might be different bus and
device on the same target.
Change-Id: I886a256f14a960d2faed71561416ee3bee20af1e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Updates the documentation as the quark platform configuration had been
previously renamed to 'galileo'.
Change-Id: I31e1920f30f57b243b07215fe92be08b5e5c9d59
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
This will enable the possibility to use this driver with Quark X1000.
Change-Id: Ic40b750d608488e97cc7662cad6c6d66dbf428ab
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Just to align the code to generic memory mapped registers and bit
operations functions.
Change-Id: I0fe8b3b6687670d0ed0daffe52645ec2c6b4c674
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit fixes the set bit function.
If the value to set is different from zero, then
the indicated bit will be set.
Change-Id: I9c42f683d108b371ca821f446ac5a10541b89b9f
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
[DL: captilize commit message title; fixed some whitespaces;
changed the __initconfig_gpio_* from level 0 to level 1,
which is the level of pure_init; and added include path
to board.h; ]
Change-Id: I7eea6a6ca9e4b7cf8d1ccabb57f07f786da93ef0
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
- Makes the code simpler in driver side
- Configuration is done on platform's config.c file and not the driver
- Handles CONFIG_PCI_ENUMERATION setting
Change-Id: I9b8376cebd7e0b62279251da132a2c4ee7b2e148
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Without it, it won't go through a pci scan, and will just trust the
pre-set information for the bus/dev/function to enable the memory
mapped registers.
Change-Id: Ica9156be541619dce9684dd45f70e05b69782a7c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will make code that use it not too crowded with #ifdef #endif
Change-Id: Iec0fa662445b1cefdc7c64d9483e1ae483106a90
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This option will be used to disable PCI enumeration (not PCI bus) to
gain in code size and execution as long as driver will be properly
configured statically. Thus setting this option as set by default.
Change-Id: I7da5d154c8ee89e44fc2bad8e85a5a20f498927e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Such controllers are found in Quark's X1000 series, and thus are found
on Galileo boards v1 and v2.
Change-Id: Ib71486c9f27de1b6c48ce3cb3dd138d69833c2ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This will be useful to enable memory mapped registers for PCI based
drivers that requires it. Removing redundant setting as well.
Change-Id: I52e47d01263a2de31c0c9f52ff65cc7e2734cf08
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will be useful for PCI based drivers to integrate fully within
the device driver model, where they will have to provide the function
they are found.
Change-Id: I7d64a4c6727cee52cbcb743c859cda43ac1a853b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add the interrupt profile points for x86 and ARM arquitectures. This
gives information regarding the time when interrupts occur.
Change-Id: Ic876c0e7f9e8819d53e0578416f09146f4456d3d
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
The uart_devs in platform config files have been converted to pointers
to struct device. This change is missing in the simple UART driver.
Change-Id: I8107f9e78daeeb3878140506f51bbd0025fde05b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The drivers provide _sys_clock_cycle_get(): moving the public APIs to
the drivers allow them to be aliases of it.
Change-Id: Ic5975a048f2b51f94510f0c3cd5e6ab3a8907718
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Converts the file description to doxygen format, and updates
the information inside. Also removes empty lines.
Change-Id: I3866843a31e30e1dd464b27cafc830900d8dce4f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Clean up variables and function arguments to conform to coding style.
Also align the function argument list.
Change-Id: I49eff429bfa369c8a544d8171e35a41523995aa3
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Converts the file description to doxygen format, and updates
the information inside. Also removes empty lines, updates
the comments for function, and adds missing comments.
Change-Id: I7610e8667cd85feb0c4c853b44880f7e29b6c05a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Clean up variables and function arguments to conform to coding
style. Also align the function argument list.
Note that this only changes the parts related to UART.
Change-Id: I84a6ba88963784f6ddc77d5bda653a7d2de6a72b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Converts the file description to doxygen format, and updates
the information inside. Also removes empty lines, and updates
the comments for function.
Change-Id: I97672996510fec1c92a30f78d6f088f02279fb44
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Clean up variables and function arguments to conform to coding
style. Also align the function argument list.
Change-Id: I0787558abe899e9376ede0ee5c5ac5728c42254d
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fix the option that enables level triggered interrupts usage.
It depends on CONFIG_HPET_TIMER_LEVEL_HIGH and CONFIG_HPET_TIMER_LEVEL_LOW
configuration parameters.
Change-Id: I3529b1e57b1625e6f0f4b05d9c15eb563e9c4f83
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The initialization procedures need to be called in the
following order:
- basic hardware initialization;
- devices initialization;
- hardware clock initialization, that the kernel needs to
run the kernel server.
This way, the board initialization routines is placed
to the pure_early_init level to make sure it runs first,
all device initialization procedures run at pure_init level,
so they are initialized early enough to be used for debugging
if needed. Hardware clock initialization is placed on
nano_early_init level to make sure hardware clock is initialized
just before the kernel server starts.
Change-Id: Ieecf9f0252c47c621b7208969687dc1113fc2ad0
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
This is just a cosmetic change to unify anything interrupt related
under 'irq'.
Change-Id: Ib8804d194e11eb49526fda952d9efc0f2ffac2df
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Move the baud rate selection for uart_console into Kconfig.
This allows apps to specify custom speed. Default is 115200
which should be supported by almost all RS232 and USB adapters
out in the past few years.
Change-Id: I78649bf2a1b2ddfc90a20d611a6454e3ad3b1b3a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is the final step to convert serial to the new driver model.
The dev->driver_api is now being used by individual drivers.
As a side effect, it is now possible to build multiple serial
drivers in the final image (though it won't make much sense).
Change-Id: I5d864e6503a5431b29006c311320155adf81cf5b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This introduces the config option CONFIG_UART_CONSOLE,
and also CONFIG_CONSOLE. The UART console can finally
be disabled if desired.
The defconfigs are also being updated.
Change-Id: I5ebaf6471986deca105971e67fcddb43374de94a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
With this, the UART console has its own initialization which is not
dependent on UART init routines.
This will allow the app to utilize all UARTs for other purposes,
instead of always reserving one for console. Future patch
will enable this choice.
Note that the console init is effectively demoted to pure_init
from pure_early_init. The UART console depends on UART being
initialized, but there is no deferred init at this point.
So this initializes the console a bit later than UARTs,
simply to make sure the UART is initialized before using it.
Once there is a mechanism for some type of deferred initialization,
the UART console init can be promoted back to pure_early.
Change-Id: Iba95197b13384cb1a46e34c78638348b7a0bec8c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This restructures the device structs and now utilizes the new
driver initialization model. This is another step towards
converting the serial driver to the new driver model.
Note that the serial driver does not initialize the hardware
unless it is being used by another driver. The configuration
of the serial port needs to be done by the driver utilizing
the port (e.g. baud rate, interrupt priority, etc.).
Therefore, some serial ports are declared but not exactly
configured.
Also note that the UART console is being initialized at
the same time as the serial port. This will be removed
in future patch, so the UART console driver will do
its own initialization.
Change-Id: Idd89954b2d0649a557ba8c869ee96512fec898e4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This encapsulates the whole serial drivers Kconfig sections, and
allows the whole section to be deactivated.
Change-Id: I84f8d35da74f3c00a44d8c17786ea2297422d68b
Signed-off-by: Daniel Leung <danielcp@gmail.com>
This moves the static device definition from the driver file,
drivers/bluetooth/uart.c, into the platform config files for
each platform.
This is another step towards converting UART drivers to
the new driver model. Also, platform config files are a more
logical place for the definition.
Change-Id: I668a52de5a38005b8b2bcb67d74437ead377cb16
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
... instead of an array index to a global array. This is
an intermediate step to make the drivers conform to
the new driver model.
This only changes from using a direct array index to using
device structs. The UARTs are still staticlly defined.
Later patches will make the drivers utilize the driver
initialization procedure specified by the driver model.
Change-Id: I18041bbb4b0efdf8ae87088fd000b391d0827e9b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The new names reflect better what the functions do: they find the first
bit set starting from the least or most significant bit, i.e. they find
the least or most significant bit set, in a 32-bit word.
Change-Id: I6f0ee4b543f6f37c2f08f7067e14e039c92a6f6a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Standardize on using the find_[first|last]_set (non-inline) symbols
everywhere.
The non-inline versions provide absolutely no benefits, so they will be
removed in a subsequent commit, and the inline versions will have their
_inline suffix removed.
Change-Id: I5b3dee33ffe3878a05e1bb3c6400a8d8c1640ad4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use doxygen format for file documentation and move
parameters to be part of the function comments.
Change-Id: I01c0614e7cd3ef4c689d2aec3aa3e52e0d21ffcd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removes the non-PIC disabling PIC code as the PIC is not a supported interrupt
controller. The PIC disabling code remains as it is needed to prevent the
generation of spurious interrupts from the PIC (see CONFIG_SHUTOFF_PIC).
Change-Id: Ic59aa17ab96f34685a5d7b5f24cab391de47edca
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The PIT is an unsupported device. On x86 based platforms, the LOAPIC_TIMER and
HPET_TIMER are the only supported timers.
Change-Id: Ic890838c811b7eb62008aef0c8a92786f1579217
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removes the LOAPIC and IOAPIC macros from board.h as they are no longer
appropriate since Kconfig options exist to use in their stead.
Change-Id: I2ce41a7a08d1859682389f35cd5a97c0e2cd5bf7
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Creating the IOAPIC and LOAPIC Kconfig options permits future commits to remove
those settings from the relevant board.h files.
Change-Id: Ie33c703f39c68d6e251d67b1c7cf75a0dd56a7e6
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removes the LOAPIC timer macros from board.h as they are no longer required
since appropriate Kconfig options exist to use in their stead.
Change-Id: Id0b509eba7cce1839b400f95b989bf886322e1a8
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Creating the LOAPIC timer Kconfig options permits future commits to remove
those settings from the relevant board.h files.
NOTE: No defconfig files have been modified as the LOAPIC_TIMER configuration
option is not enabled in any of them.
Change-Id: I7d97ed089cd4b734566b698183be95d3a166d71f
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Fixes a copy-paste error that inadvertently had the LOAPIC timer being
referred to as the PIT.
Change-Id: I4760d150cd6feb76b7d7384845898c6276bace83
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
For as long as the IOAPIC and LOAPIC code is coupled (as it currently is),
enabling LOAPIC must select IOAPIC to be enabled as well. If future commits
separate the two, then the "select IOAPIC" can be dropped.
Change-Id: Ibe7e6b86e5add19b8b3cc68ebecce760d8914c86
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removes the HPET timer macros from board.h and uses the HPET timer Kconfig
options in their stead.
Change-Id: Ia0b3cd87716277ac25f12deb31d5c5934f355050
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds additional Kconfig options to the HPET timer for setting its base address,
IRQ, IRQ priority and condition for triggering an interrupt.
Change-Id: I80349c60237380129da9ef41ccf6850c6b874c3c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
All driver Makefiles are adding the same cflags and they
have been done inconsistenly, make all drivers inherit
from the top level Makefile and remove unused includes.
Change-Id: Ie66d0ba7a418ac26f7eb709f50c887dc682e935c
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The name of the device is SYSTICK. The device name should be part of the
file name, like all other timer drivers we support. The name
'cortex_m_timer' said nothing about which device the driver is for, since
it's way too generic: it could be for any timer present on any Cortex-M
board.
Change-Id: I39b4f79c32516ec9aff82c55c0ca639fad1b52bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The Zephyr kernel must always be built as a monolithic image, not as
separate nanokernel and microkernel images.
Change-Id: I44fdd2349b32f409c84710f58bc4b3fe96fd79b7
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Removes references to obsolete BSP terminology. Where appropriate, replaces it
with platform terminology.
Change-Id: Ifb17f98bc12d3a28198810351629a109abdc18a5
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Qemu implements HPET so that it is connected to IRQ 2, which makes
necessary to use it in legacy emulation mode.
Add legacy emulation mode to HPET driver.
Change the way the HPET driver is initialized. QEMU requires that
the mode (one shot or periodic) gets set prior loading comparator
value.
Add debugging mode to HPET driver to ease the next port.
Change-Id: I668325d5968451585519a08b6c41863cf6e37f88
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Disable the PIC upon initialization to prevent it from
generating spurious interrupts.
Change-Id: I08ba1d00e269e1fd1d32960dcb844e9fa1ccc195
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Fixes the SYS_CLOCK_HW_CYCLES_PER_SEC Kconfig option dependencies such that
it can be overridden by a modified platform configuration file. This is
particularly important for the LOAPIC timer driver as
SYS_CLOCK_HW_CYCLES_PER_SEC is dependent upon the target's CPU/bus frequency.
Change-Id: I0fb49b4c540888cb1988c76e2a711a85e756f82c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Updates the timer driver dependencies to simplify the selection of a timer
driver. The timer driver menu only lists those drivers that are compatible
with the previously selected interrupt controller.
Change-Id: I5deea315f7c373c6660bacc411c6374e7b0ae84d
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Selection of the IOAPIC requires that the LOAPIC be previously selected.
Change-Id: I13d95d4bb4ff02c1aebb0b5e573cb2b89dbe530b
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The LOAPIC_TIMER_FREQ Kconfig option is not used.
Change-Id: I919fd2128f667e0b91467cb542041449738dd992
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Changes the the names of the x86 platforms so that they are more generic.
generic_pc -> ia32
quark -> ia32_pci
NOTE: it is expected that the two platforms will eventually be merged into one.
one. At present, the two platforms support different hardware. For example,
the ia32 supports bluetooth whereas the ia32_pci does not, and the ia32_pci
supports both PCI and HPET whereas the ia32 does not.
Change-Id: I8a980aaef55be8c59f7d19ddeb7fafbf11253408
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Improves code consistency by abstracting the architecture directory in the
set of assembly include paths.
Change-Id: I4b3638419a1242cb0628f128c5e3b82c3357d83c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Change the function signature of _InitHarware() function and rename
the function to a platform specific name now that it will be called
via a function pointer and not by name.
Call the platform *_init() function at PURE_INIT time.
Change-Id: I5168dfea81f406da135d491a2b4a24e8255f418a
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Update microkernel systems to use the new driver initialization model on the
timer driver.
Change-Id: Ida9ef2a395d0dddf4104d490d78b13b11ea3c347
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Update nanokernel systems to use the new driver initialization model on the
timer driver.
Change-Id: I22d8619f56052f094482d73ab34c9d610492d8c0
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Prepares the _sys_clock_driver_init() routine to interface with the new driver
model. To this end, it must accept a pointer to a device structure and return
an integer.
Change-Id: I3c600ce1efb49c0864aae7b09663ca40d6289372
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The revised name conforms to Zephyr OS naming conventions.
Change-Id: I5bcdaf1df7da9d8ce5787a08b29ead91dd8f24ce
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removing the parameter to timer_driver() as it is not used.
Change-Id: I09275287eeb541be0dd315056b4f2bc6cbc2573c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Remove function name from comment and add @brief instead.
Also capitilize first letter.
Change-Id: Ib708b49bf02e5bc89b0066637a55874e659637e0
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Previous comment style used RETRURNS:, use @return to comply
with javadoc style.
Change-Id: Ib1dffd92da1d97d60063ec5309b08049828f6661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The change replaces multiple asterisks to ** at
the beginning of comments and adds a space before
the asterisks at the beginning of lines.
Change-Id: I7656bde3bf4d9a31e38941e43b580520432dabc1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use Kconfig to define this variable and remove its
previous definitions from board.h. This will simplify
creation of different variants from a single platform.
Change-Id: I0aaa5aa81dedf096c6d8c1ea2d509c71817336d3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Moves the Cortex-M timer driver so that it resides with the other timer
drivers.
Change-Id: I3324c53356efd9f5fd88752a98e4ae301ea38d47
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds the Kconfig option for selecting the Cortex-M systick timer. This helps
pave the way for moving the Cortex-M systick timer into the drivers/ directory.
Change-Id: Iee040083a425c9c1dbc5973991b89239e0a72eee
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Updates references to CONFIG_BSP_DIR to CONFIG_PLATFORM as part of the
BSP -> platform clean up.
Note that despite the renaming, the usage of the config option remains
unchanged.
Change-Id: I2846c3f761cf09871019c0855bf1824ae03e6b3c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
We had those options defined per BSP. Moving them
to a more generic place makes more sense. In this case
they are moved under serial drivers.
Change-Id: I8faf31321fc433eaa168bf36f2b590a6b8402f9e
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The revised name better reflects the fact that the file defines
macros in addition to declaring variables. In addition, most of
these APIs use the "sys_clock_" prefix, which aligns well with
the new file name.
Change-Id: Ib33517d4b19ec2455303b87200c677e87640fcbc
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Make device drivers use static interrupt registration procedure.
DYNAMIC_INT_STUBS configuration parameter was used only by device
drivers to switch between static and dynamic interrupt registration
procedures. Now it is obsolete and is removed.
uart_int_connect() function is removed. If UART device driver still
needs to register interrupt dynamically, it should use
irq_connect(uart_irq_get()).
Change-Id: I80c695f337456e9b0c1b0fd56716e35794f7bdb7
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
In order to provide the same irq_connect() on all platforms
on x86, irq_connect() now uses a static array of interrupt
stubs. Device driver does not need to provide interrupt stub
to irq_connect() function.
Add NUM_DYNAMIC_STUBS configuration parameter, the number
of interrupt stubs used for dynamic interrupt registration.
Modify tests for unified interrupt register API
Tests that deal with interrupts are modified to work
with the new interrupt registration API.
Add CONFIG_NUM_DYNAMIC_STUBS option to dynamic interrupt projects
Projects that use dynamic interrupt handler registration on x86
have to include CONFIG_NUM_DYNAMIC_STUBS parameter in the
configuration.
Change-Id: Ic90c726485521a57cf695fd3edc8cac85d0b827d
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
In order to simplify x86 interrupt stub creation, each interrupt
controller implements an interrupt stub definition macro.
Add IRQ_CONNECT_STATIC() for static interrupt registration, and
construct the interrupt stubs name from device and interrupt
handler names.
Add IRQ_CONFIG() macro for the interrupt controller configuration.
On x86 platform it programs APIC to associate an IRQ number with
the interupt vector.
Add HPET_TIMER0_INT_PRI parameter to Quark platform header to
make it build correctly.
Change-Id: I24ad25e1aa807ffa63733a27ad882877fcad72af
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
This makes it clearer that this is a specialized API not intended for
general app usage (unlike most other things in bluetooth.h).
Change-Id: I0ce1d5903610a9b3a99cf0be9f0e1462b04bf45a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To make it clearer that these helpers are intended only for
Bluetooth-subsystem internal code, move them to a separate file.
Change-Id: Iea64780f5c61c1c96e12c9df378676bc49498fe4
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
According to section 3.7 of Documentation/kbuild/makefiles.txt, using
EXTRA_CFLAGS in Makefiles is "still supported but their usage is
deprecated."
Change-Id: Iec6121b6b79a6a8c58ac26b8b08a542eac575c22
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Since the system generator pre-registers K_ticker as the handler
for the system tick event, there is no need for the timer driver
to re-register it at run time.
Change-Id: I7f20c19e5c6ccc7dfb6117aa2d2647b9dec0e549
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
The BLUETOOTH_DEBUG_UART config option should depend on BLUETOOTH_UART
and also be sorted after it in the hierarchy.
Change-Id: I3e049e52c2e353cd0c6f1a99ca8934a289e0cce8
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Buffers returned by bt_uart_evt_recv() and bt_uart_acl_recv() may be
NULL in theory. This makes code consistent by checking return value.
Change-Id: Id39def39c8b1c4c6eefc7b2bf01702c54b3e565c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This driver is a very simple UART driver that can be used to implement
a protocol in application. It has no protocol logic and just allow
application to receive and send data over UART in platform independent
manner.
API is designed to minimize number of required memory copies.
Application is able to provide new buffer every time it decides to
consume received data. It is also able to just alter offset and
reuse current buffer eg if data was corrupted or otherwise invalid.
Change-Id: I8d3827fe2e242196e986d0419bc5487357481558
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Eliminates references to the obsolete OS name. In most cases the
name is simply removed, as it isn't necessary.
Change-Id: I32f9e7390e436aec008a9454b72657e129d65152
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Gets rid of places where there is no need to include these files
at all, or places where these files are being indirectly included
due to the inclusion of nanokernel.h.
Change-Id: I7b58148af454b977830c00a6b519a78d0595603b
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Gets rid of single-line comments required by a previous set of
coding conventions. These comments provide no value to readers
and just clutter things up.
Change-Id: I2a08b12cf5026253de56979efdfc510e7e68defe
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Closing comments to two CONFIG_MICROKERNEL ifdef blocks incorrectly identified
the ifdef block as NOT belonging to the microkernel.
Change-Id: Iee415e33d7f8a88c41009c5783b37da3a431461b
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
According to section 3.7 of Documentation/kbuild/makefiles.txt, using
EXTRA_CFLAGS in Makefiles is "still supported but their usage is
deprecated." However, using make EXTRA_CFLAGS="-DSOMETHING" results in
EXTRA_CFLAGS from Makefiles being overwritten, obviously breaking the
build. This patch converts to them to the newer ccflags-y which also
fixes the problem.
Change-Id: I6309439599d4c9cc184f9ecd941bde841982ef07
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The atomic APIs are not really tied to nanokernel-specific
capabilities, and can be used by anyone at anytime -- even
during system initialization!
Change-Id: I427954029b4b465127cb5b4b642c2f9968c17d5a
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Since the kernel now provides a minimal string library, there is
no longer any reason not to use the standard memset() and memcpy()
APIs.
Change-Id: Iad587ace6f41fd94c9c961d13d9322495a7da1be
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Renaming the directory include/nanokernel to be include/arch, which
better reflects the real nature of the directory and the contents
inside.
Change-Id: I2bc33ebc6715e2f0403227a558279fdf52398ade
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Renaming the CONFIGRUE_UART_PORT macro to UART_PORT_CONFIGURE.
Done to better align with the current naming process, but also to
remove some possible confusion over the macros source now that
the tree has moved over to Kconfig/Kbuild options.
Change-Id: I1a7691d09818c3d529de346e7fa347ce5ac19aed
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Convert the existing non-public random number generation APIs
into public APIs (i.e. sys_rand32_init and sys_rand32_get).
Change-Id: Id93e81e351a66d02c08cf3f5d2dd54a3b4b213c5
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The timer based pseudo random number generator returns the
number of system clock ticks. If the random number function is
called subsequently in a time less than a system clock tick, it
leads to getting same number.
To prevent this the counter is introduced. Counter gets changed
each call, so it ensures the caller gets different numbers each time
the random number function gets called.
Change-Id: Ibe57e1e7a23909b185623af8dbb7e80647c7ee08
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Remove ARM specific driver that duplicates the platform
independent one.
Rename x86 specific driver to make it unique.
Added configuration options for random and non-random
number generators.
Change-Id: Ie1b277d2927cdfe877650ae09134db7c86becb76
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
UART on Quark platfor, according to Quark BSP Programmer's
Reference Manual, is located in the following order on PCI bus:
COM2 BAR0: 16550 registers
BAR1: DMA registers
COM1 BAR0: 16550 registers
BAR1: DMA registers
So, the driver on Quark platform has to specify BAR (Base
Address Registers) number, the pci_bus_scan() function looks for.
As long as UART is a concole device, calling pci_show() during
it's initialization does not make any output.
Change-Id: I2261fbcc8f9e3ebc22d5307fdcbb18cb649c1224
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Added BAR (Base Address Registers) as a parameter for PCI scan.
Some devices (as UART in Quark) use two set of BARs for different
purposes. A driver may require only one of them.
BARs are numbered from 0 to PCI_MAX_BARS.
PCI_BAR_ANY means ignore the BAR number. Constants are defined
in drivers/pci.h
If device class is not specified as a scanning parameter, and
set to 0, ignore it.
Change-Id: I6b7116c5c6cf9c470ab22bec9eb74842f15b5d99
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
This commit removes the UART_INTERRUPT_DRIVEN kconfig symbol from
the console section.
The symbols is already covered as a serial driver symbol and it
is a serial feature releated configuration option.
Change-Id: I4b9438d79eb7850b1293d5d963a75ce00733dbf7
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit standardize the Kconfig inclusion.
Selective sourcing of Kconfig files create conflict when merging
different configuration files (.config files).
Instead, now each kconfig symbols is dependant of its specific
DRV_* driver ksymbol.
Change-Id: I3d20d108a83f00d34067dc334758fd57e51feecf
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit add license headers to Kconfig files.
Change-Id: I79e60263b8c7b696463ecc84b8ad411af5415117
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit organizes the bluetooth Ksymbols in:
- Driver symbols at drivers/bluetooth/Kconfig
- Stack symbols at net/bluetooth/Kconfig
Change-Id: I8ebadeb8ac7f8a769d7620e4e44077a05915dc86
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit adds the Makefile and Kconfig files
to support the bluetooth driver in the Kbuild system.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: I1f72b13aca8fb098eece04c4f0e1b680639b520f
This commit changes the dependency schemme for DRV_RANDOM.
This fix an issue that prevented the merge of this symbol
as a config overlay.
Change-Id: I734a5814af90b9c57355b78cc43f96f05c1afa96
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit fixes an issue with the inclusion path for the
board.h file for the pentium BSP.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: I28172f8071b907aa61660ec8b8009e83cb2aa5ea
This commit adaptes the Kbuild system to the change of location of
the header files for drivers.
Old location: driver/
New location: include/driver/
Change-Id: Ic49d373149ee44d781419c5c68e59408c8ef1c11
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit fixes issues to allow build on ARM architecture.
- It fixes the include paths in Makefiles.
- It fixes the include path for the offsets.c compilation.
- It fixes the linker command. This changes is needed because gcc
ARM cross-compiler does not accept an AT() command without
specifing an address explicitly. This corner case appears
on ARM architectures when XIP is disabled.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: Ief8b53c4cc154abba7b7827121ec5a56f62b7b26
This commit fixes the include path for quark BSP.
Change-Id: Idb9b5124476c0bec2d16a143407cd9d0c42e0801
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit adds the Makefiles that describe the object-bundles
for the drivers directory and every subdirectory below.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: Id77cff9cf0ab51827acc2aef32cbed3ec3ad586b
This commit adds the Kconfig files that describe the CONFIG
symbols that belongs to the drivers directory and subdirectories.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: I924835ece11a3d597e77a55ace21d724dd5ddbe5
Now that UART drivers are configured internally when it comes to
hardware specific information such as IRQ and registers (or mmaped
registers), bluetooth UART driver no longer needs to do it by itself. It
only requires to select the port it wants to use.
Change-Id: I5a30500f4b6f4155292609d0ed4a758f91930817
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
UART is configured statically into the driver directly and not anymore
in the board's system.c. Thus limiting the information to be scattered
into 2 files instead of 3. Then in future, it will also be possible to
remove driver specific informations from the generic UART API structure.
Change-Id: I001f2a6834df9a41ab395a80e4e39b347d545db3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now for x86 platforms, UART is configured statically or dynamically into
the driver and not anymore in the board's system.c. Thus limiting the
information to be scattered into 2 files instead of 3. Then in future,
it will also be possible to remove driver specific informations from the
generic UART API structure.
Change-Id: I7b7fa37f10f88316a4d375c99de3bbacf152a3e3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Remove camel case style on baseAddr, changing it into base.
Change-Id: Iea1e2d204a38912f4157cc6776a88640e29a04f6
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using "which" is somehow awkward to use when 'port', on the contrary, is
blatantly more readable.
Change-Id: I355c6e09d7c27b4b07ab6cd10b772a632855516b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using "which" is somehow awkward to use when 'port', on the contrary, is
blatantly more readable.
Change-Id: Id4d3786a192a650ca042024521b94e557a3ec7e8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This fixes many issues around PCI enumeration from old API:
- a static internal table was fed with scanning results, thus eating
memory, and worse: due to the limit of its size, scanning for new
classes was impossible unless growing statically the size of this
table --> more memory eaten! Not to mention PCI enumeration is done
once at boot time for driver initialization and that's all, so this
table is hanging around for nothing afterwards.
- one needs first to scan a class, then maybe he will be able to find
his device via pci_dev_find. Where all could be done at once.
- pci_dev_find was not trustworthy due again to the internal table. Now
if the device is not found, one will know it really went through all
the possbilities.
- still let the possibility for hard-coded BARs value on driver side
(thus no PCI scan required). However this is greatly advised not to do
so as BARs might change over a firmware/BIOS update.
Comparison:
old pci_dev_scan: could only filter out via class mask.
new pci_dev_scan: can filter out via a class, a vendor and device ID
(it could easily do the same for Function and BAR index as these are
usually fixed and informed through datasheet)
old pci_dev_scan: was limited in its findings by the size of the
internal result table.
new pci_dev_scan: can proceed through all the buses and devices every
time (there are optimizations to avoid useless work of course)
old results did not tell about the function or BAR index.
new one tells, and the structure has not bloated.
old internal code: was storing a big table of results
new internal code: is only storing a small lookup structure and an
array of Bus:Dev pairs for each PCI class for optimizations purpose.
(though, if needed, we could disable this through some #ifdef)
Usage:
- Have a local struct dev_info
- Fill it with what you want to look for, currently: only class and
vendor_id/device_id. Function and BAR index could be added if needed.
- Call pci_bus_scan_init(): this will reset the internal lookup
structure.
- Call pci_dev_scan(<a pointer to your dev_info>): at first call, the
internal lookup structure will pick up the informations from dev_info
and will try to find out what has been requested. It will return 1 on
success, or 0. On 1, your dev_info structure will be updated with the
found informations. If more devices can be found against the same
lookup informations, just call again pci_dev_scan(<a pointer to your
dev_info>) as long as it returns 1. When 0 is hit, it will mean you
found all.
Change-Id: Ibc2a16c4485ee3fed7ef4946af0ece032ae406e4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some checkpatch issues were solved by scripts leaving other problems
such as alignment and indentation issues. In order to comply with the
defined coding style the following fixes were made:
- Fixed the function declaration moving the parameters' comments above
the function in accordance to the doxygen format.
- Fixed functions' opening and closing brackets. These brackets should
not be indented.
- Fixed the 'if', 'for' and 'while' statements adding the brackets
around the sentence.
- Fixed comments' alignment.
- Fixed indentation.
The work was done manually and submitted as one commit. I didn't
separate these changes in different commits because they were fixed all
at once. Basically, all errors were fixed in every file at once.
Change-Id: Icc94a10bfd2cff82007ce60df23b2ccd4c30268d
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Replace duplicate code and will allow for further cleanup by possibly
consolidating micro/nano code that is currently guarded by preprocessor
conditionals.
Change-Id: I9aa9966c581244646b6ea317ef8b51fef9054dd4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The correct call is nano_isr_lifo_put, but they are aliases of each
other, so that never caused an issue at runtime.
Change-Id: Ibec8e6d3377133e5e67589c5a3ad1b8fb3cc652c
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Make serial console interface more robust. Enables interrupts only
when registering input, all memory is managed inside application.
Interface to application is changed to have two fifo queues. One
queue is a free line slots and another queue is keeping entered
lines. This way memory for lines is managed inside application which
provides free lines queue. It is also simpler to manage entered
lines by sleeping on fifo_get on app layer.
Change-Id: I4776c03eddd1e7d880df3b902bd48f5f2c901cad
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The coding guidelines make an exception to the Linux kernel style
where all branches, even one-liners, should use braces.
Change-Id: I368930af3033eac15f0152a6671909e401d332e6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ifadb978e31770eb9f4987a3205483aad9a525b86
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ib426dad55e318bb8176c4e7660711db1484cc245
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I6098649b507dae09d4d0f19e712bc0fe3686dfc0
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ie0770bd9ff872a9ed2b567baca1514d15fe6c90a
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Iee0936e2c92f2979b7e38f33a950108bdaf6f2c1
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
The prefix underscore is removed due to it's a local variable.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I1f95ae3c2fd44ae3bd366cd33208551cf5ea6d10
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
The prefix underscore is removed due to it's a local variable.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I5681dc0c33cc42ee48270eab418c99cc923f96b1
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
The prefix underscore is removed due to it's a local variable.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Id7391e40bb709f03c58f552d6b783cad834bbdcc
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
The prefix underscore is removed due to it's a local variable.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I28cbf0d02600d31548393870e712e6da062048da
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
The prefix underscore is removed due to it's a local variable.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ic28658f68d473b3a163fe5d97f611bfd572f140e
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
The prefix underscore is removed due to it's a local variable.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I31e267c1479dfaeeb0fba8c6ba0da45a3c011c0f
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I80ccb884f1ffd8f3740cd9298787462485b08024
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
In order to have a better compiler support consolidate
inline assembler code in a set of header files.
If another compiler is used, that supports a different
inline assembler format, asm_inline_<compiler name>.h
heder files have to be provided.
Change-Id: Iecc7d96419efd767a8463933badd4db4a557de5b
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Configuration option BLUETOOTH_DEBUG_UART enables debug support for
Bluetooth UART driver.
Change-Id: I192f380be492df1a52ad212239447b6ee4b50aac
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
When the 'len' and 'min' parameters passed to bt_uart_read() are equal
the function is guaranteed to always return 'len' (it will keep
looping until that). This patch removes bt_uart_read() error checks
which would never occur in practice.
Change-Id: Icd879f1e15c6d33acc549155aabd24490098ffc5
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are some places where it's forgivable if bt_uart_read() wasn't
able to read as many bytes as requested. In other places it's not
acceptable (e.g. when reading ACL or event header). To avoid failing
in situations where we can handle receiving less data than requested
this patch adds a new parameter to bt_uart_read() to specify the
minimum required data amount.
Change-Id: I372e3af7aaa6bfabe14896eb10cc71c3deff94f2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we're out of buffers the UART driver would previously loose sync of
where the packet boundaries go, because it was using the buffer itself
to store and parse the HCI packet headers. This patch modifies the
UART driver to use stack variable for initial header parsing, thereby
being able to always determine how many remaining bytes there are and
cleanly discard the bytes until the beginning of the next packet.
Change-Id: I278f3fc0c983e6a2a6904356ef1af1d25c9f06e4
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we get an invalid packet type here the buf pointer will be NULL.
Going to the cleanup section at the end of the function would trigger
a bt_but_put() call which would cause a NULL pointer access. Directly
returning from the function is the right thing to do instead.
Change-Id: I0c18646e0820cf829ef8aa3f77835ba0a14375b5
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We may soon want to have a _wait() variant of bt_buf_get, so to avoid
the number of 'get' function growing too large consolidate the
existing get() and get_reserve() functions into a single one. The new
consolidated function also takes the type as input parameter so that
we know this from the very start and thereby plan for the split into
multiple buffer pools.
Change-Id: Ia09448565349def2be9bc08d9510fedd029480b4
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We'll soon want to have dedicated pools for outgoing and incoming ACL
data. To know from which pool to get and put the buffers each buffer
should contain enough information to distinguish the two types. This
patch splits the old BT_ACL type into two new BT_ACL_IN & BT_ACL_OUT
types.
Change-Id: I7d3c05c26d2a70f80fb1229e245aa21673ec378b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of drivers/pci/, the public API headers will be found in
include/drivers/pci.
Change-Id: I577036660383e6bd9c015d6bbbcbc14bf8fb67ec
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Only moving the header from drivers/console/uart_console.h to
include/drivers/console/uart_console.h so source file did not need to be
changed, only the defs.objs files to look into include/drivers/console.
Change-Id: I585e16b50d9ffecf01ca9225e80f0e101f62ee4c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename camelCase uartConsoleInit function for consistency with the
rest of the code in serial console.
Change-Id: I519737070538e9c0f52a8d110a3eff68e0185ce2
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Following comments received during review rename console_uart_isr to
uart_console_isr for consistency reason.
Change-Id: Ibee1dec40ee19a9095f78969a07ffb73518fffbb
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch adds a simple HCI UART (H4) driver that currently maps to
the second UART in the system. The main intention is to use this
together with qemu for accessing the Bluetooth controller available on
the host OS side.
The H4 HCI transport protocol is perhaps the simplest of the standard
HCI transports. It consists of a single byte in the beginning of each
packet which indicates the type of the packet: HCI event, HCI command,
ACL data, or SCO data (which we don't use at the moment).
Change-Id: I225a2a2361fbd7cd4ba82ea1f81ddc1271e9e7c2
Co-authored-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I4e5c9419fe0ccbc4b2990b96fc95c697decc18e0
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I5e249e34ee9666666e31db6b9f71fe2abcc22400
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I2e501394b7fa4264d9854659e2dd008e5c94b540
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Iebefec0e02cbb838564dd71fd4424c1adbff31f5
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Rename UART_HOSTDRV_INTERRUPT_DRIVEN option to
UART_INTERRUPT_DRIVEN removing old definition.
Change-Id: Id48288db42e97a1ecbd809e259f33359d5a7c9d7
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Serial console handler when registered allows to interact with serial
line. It can either execute callback from ISR or defer execution to
fiber or task. This will be used in Bluetooth development for tests and
simple interaction with Bluetooth stack.
Change-Id: Ia960b456a75062d614baea324608058d979aa11b
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Adding a line after variable declaration in order to comply with
the defined coding style.
Change-Id: Id41af88404bd37227bfd59a2d71ce08d0d6ce005
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
