Add generic SoC support for the supported nordic SoCs:
- nrf5340
- nrf9160
- nrf9120
Add generic SoC support by taking board specific configurations from
zephyr devicetree and kconfig.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Exception info dump is a very basic feature so it should IMHO be
enabled by default.
For instance, a simple null-pointer exception in the non-secure app
will not be logged unless this option is enabled.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Uart driver for openthread have been waiting for host to start
communicating with coprocessor, during booting of the Zephyr and
by that blocking start os OS. There is no longer a need for
that since the stack will be soft rebooted after host connects
to coprocessor, removing the need to wait on host communication.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
This change slightly simplifies the configuration of a CSL receiver and
generalized CSL_RX_TIME to EXPECTED_RX_TIME as a re-usable primitive
across several timing-sensitive IEEE 802.15.4 standard sub-protocols
(namely BE-PANs/DSME/CSL/RIT/TSCH).
This API change is based on the rules outlined in RFC #61227.
Fixes: #62918
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Improves standard conformance of the IEEE802154_CONFIG_ENH_ACK_HEADER_IE
option and introduces certain "soft MAC" capabilities around header IEs:
* Introduces types and helpers that allow driver maintainers to
represent, parse, write and validate header IEs.
* Introduces helper functions to access non-aligned fields in header
IEs, namely element IDs.
Updates the only existing L2 and driver pair that uses
IEEE802154_CONFIG_ENH_ACK_HEADER_IE: OpenThread platform radio and nRF5
and improves header IE validation in the nRF5 driver.
This change should help further driver maintainers to support
OpenThread's CSL and vendor IE extensions. It is based on the rules
specified in RFC #61227.
It is also a precondition to generically support both, "soft MAC" and
"hard MAC", approaches to header IEs in the TSCH protocol, namely the
time synchronization IE.
Fixes: #62940
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
"Sleeping" has a well defined meaning in Zephyr related to threading and
power management. This differs from OpenThread's definition:
- Deprecates the "SLEEP_TO_TX" capability as it is redundant and
conflicts with all of Zephyr's nomenclature, #61227, RFC 2863, Thread
standard and IEEE 802.15.4. This binds the API to an implementation
detail of OpenThread, instead. See #63670 for the agreed migration path.
- Renames the "SLEEP" event to "RX_OFF" which conforms to the
nomenclature in Zephyr, this API and IEEE 802.15.4.
Fixes: #62995
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
According to cmake documentation, in the `if(<string>)` expression
the string evaluates to false unless its value is one of the true
constants. Thus, the commands under `if(${uicr_path})` are never
executed. Use `if(DEFINED uicr_path)` instead, since `uicr_path`
is returned by `dt_nodelabel()` and it will be undefined if such
node does not exist.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add option for overriding the maximum number of wait loop iterations for
entering/leaving freeze mode. Set the default to 10000 (as opposed to a
default of 1000 used in the HAL).
Fixes: #56171
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
rand32.h does not make much sense, since the random subsystem
provides more APIs than just getting a random 32 bits value.
Rename it to random.h and get consistently with other
subsystems.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
CONFIG_HAS_MCUX is also selected by ARM64 and XTENSA-based cores
which don't have any CMSIS files. As such, it's wrong to implicitly
select CONFIG_HAS_CMSIS_CORE when CONFIG_HAS_MCUX is selected. Since
the ARM32-based cores implicitly select CONFIG_HAS_CMSIS_CORE there's
no point in CONFIG_HAS_MCUX also selecting it too.
The old approach caused config-related warnings
in external projects such as SOF after the introduction of
Commit '8d5ed53' ("modules: remove uncessary source for
external cmsis kconfig"). The warnings were in the form of:
"HAS_CMSIS_CORE (defined at modules/cmsis/Kconfig:7) has
direct dependencies 0 with value n ..."
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
ethosu_log.h uses the stdout as it's stream for printf. This could
cause an issue where if CONFIG_LOG=n and CONFIG_CONSOLE=y then there
would be no way to control the log level and it would default to debug
level. There is no NONE option as with the way the ethos-u hal is set
up with no way to go below the err level.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
A little refactoring that simplifies dealing with nanosecond timestamp
values in packets and further decouples calling code from PTP:
Benefits:
- simplifies calling code by removing redundant conversions.
- prepares for removing PTP dependencies from net_pkt.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Do not select HAS_CMSIS_CORE for SOC_FAMILY_NXP_ADSP.
This soc family refers to the Audio DSP from i.MX MPU,
which is a HiFi4 core, Xtensa arch.
HAS_CMSIS_CORE is for ARM cores (A, M, R cores) -
see modules/cmsis/Kconfig.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
CMSIS uses an external KConfig so sourcing the KConfig is uncessary. This
also adds a comment if it is not available.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The names have underscores within them. Somehow it was still being found
within the build but not with building documents. This renames them to
the correct name.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Code using sys_csrand_get should depend on CONFIG_CSPRNG_ENABLED symbol
and not in ENTROPY_HAS_DRIVER since they are not using the entropy
device directly.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The CONFIG_MCUBOOT_BOOTLOADER_MODE_DIRECT_XIP has been missing
select of CONFIG_MCUBOOT_BOOTLOADER_MODE_HAS_NO_DOWNGRADE.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Changes the Kconfig symbols for the sys_heap based memory management option
and removes the notion of `BLOCKS` with a more concise single
`LV_Z_MEM_POOL_SIZE` option. Also adds `LV_MEM_CUSTOM` to the lv_conf.h,
since in any option the memory management is considered to be custom.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Add the MCUBOOT_BOOTLOADER_NO_DOWNGRADE Kconfig option that allows,
when paired with MCUboot mode Kconfig, to indicate that the MCUboot
has been configured with downgrade prevention, which means that only
application with version higher than running can be swapped on next boot.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit adds support for uploading image to board with MCUboot
configured with DirectXIP with revert.
It allows to set uploaded image either for test or as permanent
boot application, until newer image gets confirmed.
Note that in DirectXIP with revert MCUboot will remove image
that has not been set for test nor confirmed and MCUmgr does not
set either mode unless image has the mode set within uploaded
binary.
The commit adds Kconfig option
CONFIG_MCUBOOT_BOOTLOADER_MODE_DIRECT_XIP_WITH_REVERT
that enabled the new mode of operation within MCUmgr.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This adds the cmsis-nn module since it moved to its own realm.
This also adds a kconfig for the long short-term memory.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Use CMSIS-DSP from its new realm. This also changes change how you
initialize FFT tables as well to use arm_cfft_init_64_f32 if you
know the FFT size in advance rather than the generic initialization
arm_cfft_init_f32.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Adds CONFIG_STM32_ENABLE_DEBUG_SLEEP_STOP to allow debugger attaching in
sleep/stop mode of STM32 parts. Mainly useful for debugging. Move DBGMCU
from part-sepcific power.c to common soc_config.c. CONFIG_USE_SEGGER_RTT
depends on this as well.
Signed-off-by: Roland Lezuo <roland.lezuo@embedded-solutions.at>
Also set the HAL variant appropriately when building for
the new nrf53_bsim boards.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Adds saving of the last lv_indev_data_t for button and pointer type
devices. This is needed because there is currently no way to tell LVGL in
the read callback that no event is pending. Preservation of the last state
is expected to happen in the port layer for the input devices.
This resolves issue #62512.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
If asserts are disabled, there is a warning in 'otPlatCryptoInit'
regarding unused variable `err`. This commit fixes that.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
Synchronizes with the new upstream RX/TX timestamp definition in
OpenThread based on the standard's SFD.
This change is synchronized with the upstream OpenThread implementation
via west.yml.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Removes the pseudo device prerequisite that the LVGL setup routine has been
executed before initialization. The pseudo devices are now registered at
the end of the LVGL setup routine, the driver is not concerned with
configuring the devices anymore. This also removes the need for enforcing
certain priorities within the same init level.
This resolves issue #62753.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
So that the HAL's system init function configures the reset GPIO as
nRESET if requested by the user.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
If the users configures this option in devicetree, ie,
```
&uicr {
nfct-pins-as-gpios;
};
```
CMake will inject the HAL-specific CONFIG_NFCT_PINS_AS_GPIOS definition,
so that the necessary operations are performed during system init.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Instead of detecting that we are in a native/POSIX arch based
board by checking for each board specifically,
let checks for the architecture.
In that way other boards (like the upcoming nrf53_bsim ones)
will also work.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Introduce a helper function zephyr_nanopb_sources to generate
source files and add these to a target.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Move the conditional compile of CONFIG_ACPI to the beginning of the file
as we currently add compiler include paths to all projects even if
CONFIG_ACPI is not set.
Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>
Adds a missing include to avoid these warnings :
- zephyr/modules/fatfs/zfs_ffsystem.c:19:16: warning: implicit declaration
of function 'k_malloc'; did you mean 'ff_memalloc'?
[-Wimplicit-function-declaration]
- zephyr/modules/fatfs/zfs_ffsystem.c:19:16: warning: returning 'int' from
a function with return type 'void *' makes pointer from integer without a
cast [-Wint-conversion]
- zephyr/modules/fatfs/zfs_ffsystem.c:25:9: warning: implicit declaration
of function 'k_free' [-Wimplicit-function-declaration]
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
This commit instructs mbedtls to use 64-bit alignment in its internal
memory allocation routines when targeting 64-bit platforms. By default
mbedtls uses 32-bit alignment regardless the platform, what may result
in misaligned memory accesses, possibly inducing access time overhead or
exceptions
Signed-off-by: Vladimir Graudt <vladimir.graudt@syntacore.com>
Add a pseudo device which can be used to hook into qdec events and
optionally a button and relay the input_event to lvgl.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
This commit follows the parent commit work.
This commit introduces the following major changes.
1. Move all directories and files in 'include/zephyr/arch/arm/aarch32'
to the 'include/zephyr/arch/arm' directory.
2. Change the path string which is influenced by the changement 1.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
This commit adds the DFM (DevAlert target side code) module and
moves the TraceRecorder module into the percepio module, which
results in the TraceRecorder module definition being removed
from the west manufest and module definition within zephyr.
Signed-off-by: Aron Lander <aron.lander@percepio.com>
Call lvgl_heap_init from lvgl_init rather than using two separate
SYS_INIT, this sensures that the heap is initialized correctly
regardless of the relation between CONFIG_KERNEL_INIT_PRIORITY_DEFAULT
and CONFIG_APPLICATION_INIT_PRIORITY.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
add support for retrieve MAD and DMAR table information. Provided
two new interface namely acpi_dmar_entry_get() and acpi_drhd_get()
for retrieve DMA Remapping Reporting and DMA-remapping hardware
unit definition (DRDH).
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
Includes the application VERSION-file designated tweak version
for the build number field when signing MCUboot images.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add a pseudo device which can be used to hook into gpio-keys input_events
and relay the events to a lv_indev.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Moves lvgl pointer driver handling based on kscan to its own file, to ease
deletion when the usage of kscan for display touch input has been
deprecated.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Add the scaffolding to create input lvgl pseudo devices which route zephyr
input_event to their lvgl `indev` equivalent. As a first cut also add a
`zephyr,lvgl-pointer-input compatible which can be a drop-in replacement
for the existing kscan solution.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
In OpenThread, Settings are initialized after KeyManager by default.
If device uses PSA with emulated TFM, Settings have to be initialized
at the end of otPlatCryptoInit(), to be available before storing
Network Key.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
The CMSIS module glue code was part of arch/ directory. Move it to
modules/cmsis, and provide a single entry point for it: cmsis_core.h.
This entry header will include the right CMSIS header (M or A/R).
To make this change possible, CMSIS module Kconfig/CMake are declared as
external, allowing us to add a new Zephyr include directory.
All files including CMSIS have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move CMSIS module Kconfig options to a folder, in preparation for CMSIS
core header creation.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Enable offloading of display_write call to background thread for color
displays. This feature is opt-in, as it may offer significant
performance gains for every display pipeline.
When enabled display_write and lv_disp_flush_ready will be called from a
background thread. This means that while the display driver waits on the
hardware to render the framebuffer, the LVGL rendering thread will not
be blocked.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Changes the lvgl filesystem `tell()` wrapper to check for errors returned
by zephyr filesystem subsystem.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Changes the memory management for the lvgl filesystem wrapper to use the
memory management strategy selected by kconfig. Additionally fixes memory
leaks if fs_{file,dir}_t initialization failed.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
The prototype of `nrf_802154_energy_detected` callout has changed.
This commit adjusts to this change.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Commit adds configuration for mesh with mbedtls PSA
to CI BabbleSim tests as well as emulation of
the Internal Trustable Storage(ITS) based on Zephyr's
settings to run in parallel environment.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Based on the standard based definitions given in previous commits, the
TX timestamp used for timed TX now refers to the start of PHR. As OT
continues to calculate timestamps based on a "start of SHR" definition,
the duration of the PHY specific SHR is added in the OT adaptation layer
to make up for this OT quirk.
Fixes: #59245
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Builds upon the newly introduced nrf_802154_phr_timestamp_get() function
to calculate RX timestamps according to the timestamp definitions
introduced in earlier commits and removes the prior workaround to
calculate the start-of-frame message timestamp point.
Fixes: #59245
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
OT does not have 64 bit timestamp support. This is a limitation of OT
and not of the IEEE 802.15.4 driver API. Therefore any workaround
related to such OT idiosyncracies should be encapsulated inside the OT
adapatation layer.
This change moves the OT-specific conversion of OT 32 bit timestamps to
Zephyr 64 bit timestamps into the OT adaptation layer.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Update trusted-firmware-m to 1.8.0, mbedtls to 3.4.0, and tf-m-tests to
1.8.0. Includes minor cmake changes due to file renames and such, as well
as adjusting the return type of a callback function that has changed since
the previous version of trusted-firmware-m.
Signed-off-by: David Brown <david.brown@linaro.org>
This commit introduces Kconfig symbols for enabling logging
for each nrfx drivers in Zephyr.
Example Usage:
To enable logging for the NRFX ADC driver, add the following
line to the project's configuration file (prj.conf):
CONFIG_NRFX_ADC_LOG=y
The purpose of this change is to enable selective logging
in Zephyr for specific nrfx drivers.
Signed-off-by: Natalia Pluta <natalia.pluta@nordicsemi.no>
A Kconfig symbol mapping is necessary to enable logging for specific
nrfx drivers in Zephyr, allowing the association of these symbols with
their corresponding nrfx-specific symbols.
Signed-off-by: Natalia Pluta <natalia.pluta@nordicsemi.no>
The Zephyr-specific Segger SystemView configuration was not used as
the same file was available inside the external Segger module with
higher import priority.
Fixes the regression by moving the SystemView configuration to the same
place in the external module where RTT configuration already resides and
thereby creates a canonical include path to avoid further regressions of
the same kind.
Fixes: #61133
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
This version introduces support for the syscalls extension,
which greatly reduces the amount of bandwidth being used
for tracing syscalls.
Signed-off-by: Aron Lander <aron.lander@percepio.se>
TFM redefines functions from mbed TLS's psa_crypto_slot_management.c,
therefore that file should not be included in build when TFM is enabled.
Otherwise, the linker reports an error about redefined functions like
psa_open_key() etc.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Following the same pattern as in the other libraries/samples, add TFM
include directory explicitly when building uoscore library, to mitigate
the problem of redefined header files in TFM. When TFM is enabled,
headers from TFM should be used, not mbed TLS ones.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Update uoscore-uedhoc repository to the latest revision.
Align uoscore tests with the API changes.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
After an update to mbed TLS 3.3.0, dependencies with
CONFIG_MBEDTLS_PSA_CRYPTO_C enabled got affected.
mbed TLS in its build_info.h file, enables MBEDTLS_PK_WRITE_C config
under the hood. MBEDTLS_PK_WRITE_C has a dependency to
MBEDTLS_ASN1_WRITE_C which wasn't reflected anywhere.
Therefore, update Kconfig.tls-generic to enable
CONFIG_MBEDTLS_PK_WRITE_C automatically, when PSA crypto is enabled, to
reflect mbed TLS configuration pattern. Additionally, enable
MBEDTLS_ASN1_WRITE_C automatically, when PK write is enabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The psa_generate_random function requires the psa_crypto_init call
before the usage. This can be ensured by calling the psa_crypto_init
in otPlatCryptoRandomInitfunction.
Signed-off-by: Arkadiusz Balys <arkadiusz.balys@nordicsemi.no>
The Thrift library has its own abstraction for mutexes, which
normally just a wrapper around `std::mutex` using the PIMPL
idiom (pointer-to-impl).
Since Zephyr does not yet support `std::mutex`, a workaround
was added in Zephyr that was essentially no-op, and actually
the PIMPL idiom made it quite easy to do that. However,
pretending there is no synchronization requirement is not a
solution for it.
We can't yet just use a `struct k_mutex` yet, because we
don't yet support userspace, but for now we can fake a mutex
interface with a spinlock.
We hope to eventually drop this workaround entirely and just
support `std::mutex`.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
The IEEE 802.15.4 API and networking subsystem were using several
inconsistent timestamp resolutions and types. This change defines all
timestamps with nanosecond resolution and reduces the number of
available types to represent timestamps to two:
* `struct net_ptp_time` for PTP timestamps
* `net_time_t` for all other high resolution timestamps
All timestamps (including PTP timestamps) are now referred to a
"virtual" local network subsystem clock source based on the well-defined
types above. It is the responsibility of network subsystem L2/driver
implementations (notably Ethernet and IEEE 802.15.4 L2 stacks) to ensure
consistency of all timestamps and radio timer values exposed by the
driver API to such a network subsystem uptime reference clock
independent of internal implementation details.
The "virtual" network clock source may be implemented based on arbitrary
hardware peripherals (e.g. a coarse low power RTC counter during sleep
time plus a high resolution/high precision radio timer while receiving
or sending). Such implementation details must be hidden from API
clients, as if the driver used a single high resolution clock source
instead.
For IEEE 802.15.4, whenever timestamps refer to packet send or receive
times, they are measured when the end of the IEEE 802.15.4 SFD (message
timestamp point) is present at the local antenna (reference plane).
Due to its limited range of ~290 years, net_time_t timestamps (and
therefore net_pkt timestamps and times) must not be used to represent
absolute points in time referred to an external epoch independent of
system uptime (e.g. UTC, TAI, PTP, NTP, ...).
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Previously, the binary protocol variant of ThriftTest would fail
consistently in CI for `qemu_x86_64` with the message below.
```
E: failed to poll fds -1, -1: 1
```
Note: 1 corresponds to EPERM
The root cause of this is that we do not yet have support for
standard synchronization primitives in C++, and there is
slightly racey behaviour in thrift until we do have support
for standard synchronization primitives.
With the addition of dynamic thread stacks, conforming pthreads,
and some additional work in the toolchain area
(re gthr-posix.h), we should soon be able to enable proper
synchronization primitives.
This change is a temporary workaround but solves the
test failure (which would occur even when tests all passed).
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 4 (CCU4)
module. There are four CCU4 with each one having four channels
Thus it's possible to have up to 16 pwm output signals. The output of
each channel can only be connected to a specific port/pin. The possible
connection and gpio configurations are defined using pinctrl.
The CCU4 module also has a capture mode. Capture support will be added
in the future.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Add a kconfig symbol to control the mbedtls option
`MBEDTLS_AES_FEWER_TABLES`. 6KiB is a not insignificant ROM/RAM savings,
and the extra arthmetic is quite reasonable.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Fix help text for crypto key module functionality, which is included
in the source file of crypto_key_management.c source file.
The crypto_key.c source file contains generic code that is always
included.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update trusted-firmware-m to 1.8.0, mbedtls to 3.4.0, and tf-m-tests to
1.8.0. Includes minor cmake changes due to file renames and such, as well
as adjusting the return type of a callback function that has changed since
the previous version of trusted-firmware-m.
Signed-off-by: David Brown <david.brown@linaro.org>
The ILPS22QS sensor cannot be enabled unless USE_STDC_ILPS22QS is defined.
This PR fixes#57825 add adds the missing item in Kconfig.st file.
Signed-off-by: Raoul Rubien <rubienr@sbox.tugraz.at>
This commit replaces direct entropy device driver class with
`sys_csrand_get`, which is recommended way of getting crypto
secure random buffer.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
nRF USBD ISOINCONFIG register controls USBD behavior after receiving IN
token addressed to ISO IN endpoint when the endpoint was not armed with
data. The options are:
* NoResp, in which case there is no response (i.e. bus timeout)
* ZeroData, in which case device responds with ZLP
This commit both makes the ISOINCONFIG value configurable and changes
the default from NoResp to ZeroData. For reference, DWC_otg controller
will always send ZLP in such case and does not have NoResp equivalent.
Automatically sending ZLP when ISO IN endpoint is not armed resolves
periodic audio dropouts observed on Mac OS with USB Audio headset
sample. Apple USB Audio class driver will attempt recovery (abort all
pending URBs, switch to alternate config 0, switch to active alternate
config and submit new URBs) every time it sees kIOReturnNotResponding
status code. During recovery no audio data can be transferred and
therefore there are gaps in the audio stream.
Apple USB Audio driver sees kIOReturnNotResponding when there is bus
timeout (i.e. IN token was sent to nRF when the endpoint was not armed
and NoResp option was active). Activating ZeroData option results in
perfectly fine (albeit short) packet that does not trigger interface
recovery and thus fixes the USB Audio issues on Mac OS.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Fix board selection for Musca B1 board.
The platform path in TF-M was changed in the TF-M 1.7.0 update.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
- This includes the driver, test app, and sample app
- Only the boards\arm\xmc47_relax_kit board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
The IEEE 802.15.4 stack defines radio API helpers that provide
simplified and encapsulated access to radio API features.
These helpers were missing the `_radio_` infix. This infix is introduced
to clearly distinguish between MAC and PHY concerns. While PHY features
may be shared between L2 implementations (including the functions
concerned here), this is not true for MAC features.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Some NXP S32 devices share common harwdware blocks with other non-S32
devices which are already supported using MCUX-based drivers. In order
to leverage existing support, allow to build with MCUX enabled for NXP
S32 family.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
SYS_INIT() requires pointer to function that takes `void` now, instead of
pointer to device structure. Since the commit was developed before that
switch, it still invoked it with NULL. Fix that now.
Fixes:
zephyr/modules/mbedtls/zephyr_init.c: In function 'mbedtls_init':
zephyr/modules/mbedtls/zephyr_init.c:108:16: error: too many arguments \
to function '_mbedtls_init'
108 | return _mbedtls_init(NULL);
| ^~~~~~~~~~~~~
zephyr/modules/mbedtls/zephyr_init.c:86:12: note: declared here
86 | static int _mbedtls_init(void)
|
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Add a config flag to enable conditional mbebtls
initialization at startup, defaulting to enabled.
Also add a function, mbedtls_init(), that should be
called by platforms that wish to initialise mbedtls
at a time of their choosing.
Signed-off-by: Eugene Cohen <quic_egmc@quicinc.com>
Signed-off-by: Dave Aldridge <quic_daldridg@quicinc.com>
These are referenced by the "x module not available" message in
modules/Kconfig, but were only defined in the module, were generating an
undefined symbol warning when running CI compliance with no modules.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The RTT backend of the shell does not support several of the more
advanced terminal features. This commit proposes to inactivate these
features by default when RTT is selected as shell backend.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The method ieee802154_radio_handle_ack() does not belong to the
PHY/radio layer but to the L2 layer. It is a callback called from the
radio layer into the L2 layer and to be implemented by all L2 stacks.
This is the same pattern as is used for ieee802154_init(). The
'_radio_' infix in this function is therefore confusing and
conceptually wrong.
This change fixes the naming inconsistency and extensively documents
its rationale.
It is assumed that the change can be made without prior deprecation of the
existing method as in the rare cases where users have implemented custom
radio drivers these will break in obvious ways and can easily be fixed.
Nevertheless such a rename would not be justified on its own if it were
not for an important conceptual reason:
The renamed function represents a generic "inversion-of-control" pattern
which will become important in the TSCH context: It allows for clean
separation of concerns between the PHY/radio driver layer and the
MAC/L2 layer even in situations where the radio driver needs to be
involved for performance or deterministic timing reasons. This
"inversion-of-control" pattern can be applied to negotiate timing
sensitive reception and transmission windows, it let's the L2 layer
deterministically timestamp information elements just-in-time with
internal radio timer counter values, etc.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
A mesh key type has been added to be able to choose the different
key representation for different security libraries.
The type as well as some functionality related to Mesh key
management has been added as a public API.
If tynicrypt is chosen then keys have representation
as 16 bytes array. If mbedTLS with PSA is used then keys are
the PSA key id. Raw value is not kept within BLE Mesh stack
for mbedTLS. Keys are imported into the security library
and key ids are gotten back. This refactoring has been done
for the network(including all derivated keys), application,
device, and session keys.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
This allows the MIPI Sys-T library to be built with minimal C
library. This is due to lack of support for wchar in our
minimal C library. This simply tells the library to skip any
wchar support.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The RSSI value in net_pkt (net_pkt_cb_ieee802154.rssi) was used
inconsistently across drivers. Some drivers did cast a signed dBm value
directly to net_pkt's unsigned byte value. Others were assigning the
negative value of the signed dBm value and again others were offsetting
and stretching the signed dBm value linearly onto the full unsigned byte
range.
This change standardizes net_pkt's rssi attribute to represent RSSI on
the RX path as an unsigned integer ranging from 0 (–174 dBm) to 254 (80
dBm) and lets 255 represent an "unknown RSSI" (IEEE 802.15.4-2020,
section 6.16.2.8). On the TX path the rssi attribute will always be
zero. Out-of-range values will be truncated to max/min values.
The change also introduces conversion functions to and from signed dBm
values and introduces these consistently to all existing call sites. The
"unknown RSSI" value is represented as INT16_MIN in this case.
In some cases drivers had to be changed to calculate dBm values from
internal hardware specific representations.
The conversion functions are fully covered by unit tests.
Fixes: #58494
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
It looks like LV_Z_DPI is not used anywhere and only lived in the
context of an incorrect board symbol definition so far (moved to
Kconfig.lvgl in the previous patch).
This was probably meant to be LV_DPI_DEF (which actually exists in the
LVGL module) and was renamed incorrectly, fix it by renaming it
everywhere.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Some boards override default for few LVGL LV_Z_* symbols. This causes
the build to fail if the module is not present in the system, and has
been worked around on one board by repeating the types in the board
Kconfig file.
Fix this properly by defining the known type for all symbols used in
boards in modules/Kconfig.lvgl.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
`tfm_fwu_api.c` was missing from the list of possible source files
to be exported from TF-M, which is required when
`CONFIG_TFM_PARTITION_FIRMWARE_UPDATE` is defined.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
The IEEE802154_2015 option is misleading, as it does not introduce full
802.15.4-2015 standard compliance but only random bits, plus it's
defined at the radio driver level, which brings yet another confusion.
Because of that, the option will be deprecated, and respective parts of
code that made use of it converted to use more specific configurations:
* nRF driver will now use CONFIG_NRF_802154_ENCRYPTION to specify
whether to compile in TX security
* net_pkt will only add extra 802.15.4 control block fields if
OpenThread is used, as they were solely used by this L2
* OpenThread radio layer will now use the OpenThread version to
determine whether to compile in TX security.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Previously, Zephyr's mbedtls module's cmake build created a single static
library, rather than the collection of libraries (mbedtls, mbedcrypto,
and mbedx509) that upstream mbedTLS cmake provides.
To give better control at link time to choose the required libraries to
link, this commit updates the Zephyr MbedTLS module to also define a
collection of libraries rather than a single static MbedTLS library.
One benefit of the three library approach is that if mbedTLS is used in
Zephyr in the the non-secure application in addition to TFM's PSA Crypto
API on the secure side with TF-M, PSA API calls on the non-secure side
will be redirected to the TFM PSA implementation, and the mbedcrypto
library will only be linked to the secure (TF-M) binary, with the mbedtls
and mbedx509 libraries linked against the non-secure (Zephyr) binary,
enabling TLS calls to PSA crypto to be redirected to mbedcrypto in the
secure partition and avoiding function duplication in the non-secure
binary.
Signed-off-by: Rajkumar Kanagaraj <rajkumar.kanagaraj@linaro.org>
nRF52 in case of USB CDC required `CONFIG_USB_DEVICE_INITIALIZE_AT_BOOT=n`
Due to incorrect error check in `otPlatUartEnable`.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
After the MCUboot configuration options were moved out of the main
Kconfig.zephyr they were placed in a new Kconfig.mcuboot in the root of
the repo. This is not right, and the file belongs in the modules/
folder.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The LSM6DSV16X is a system-in-package featuring a 3-axis digital
accelerometer and a 3-axis digital gyroscope for industrial and IoT
solutions. The LSM6DSV16X embeds advanced dedicated features such as
a finite state machine (FSM) for configurable motion tracking and a
machine learning core (MLC) for context awareness.
https://www.st.com/en/mems-and-sensors/lsm6dsv16x.html
This driver is based on stmemsc HAL i/f v2.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds implementation of following new api functions from
openthread:
- otPlatCryptoEcdsaGenerateAndImportKey
- otPlatCryptoEcdsaExportPublicKey
- otPlatCryptoEcdsaVerifyUsingKeyRef
- otPlatCryptoEcdsaSignUsingKeyRef
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
The LSM6DSO16IS is a system-in-package featuring a 3-axis digital
accelerometer and a 3-axis digital gyroscope for industrial and IoT
solutions. The LSM6DSO16IS embeds a new ST category of processing,
ISPU (intelligent sensor processing unit) to support real-time applications
that rely on sensor data. The ISPU is an ultra-low-power, high-performance
programmable core which can execute signal processing and AI algorithms
in the edge.
https://www.st.com/en/mems-and-sensors/lsm6dso16is.html
This driver is based on stmemsc HAL i/f v2.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enable UART on the DSP from the i.MX8MP target:
- add corresponding nodes in dtsi and dts;
- create a dts overlay for uart;
- add a config fragment for uart and console configuration.
So, in order to compile an application and enable UART
a user must run west build using DTC_OVERLAY_FILE and CONF_FILE.
Here's an example for hello_world:
west build -p always -b nxp_adsp_imx8m samples/hello_world/
-DDTC_OVERLAY_FILE="boards/xtensa/nxp_adsp_imx8m/
nxp_adsp_imx8m_uart.overlay" -DCONF_FILE="boards/xtensa/nxp_adsp_imx8m/
nxp_adsp_imx8m_uart.conf"
For other applications, like SOF, where we don't need UART, we simply run:
west build -p always -b nxp_adsp_imx8m ../modules/audio/sof/ --
-DTOOLCHAIN=/opt/zephyr-sdk-0.15.2/xtensa-nxp_imx8m_adsp_zephyr-elf/
bin/xtensa-nxp_imx8m_adsp_zephyr-elf -DINIT_CONFIG=imx8m_defconfig
The nxp_adsp_imx8m is using the nxp_imx_iuart driver.
For now, is used in poll mode.
Next step is to enable the interrupt controller in
DSP and use the interrupt driver UART.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
- Added initial version of Infineon CAT1 Flash driver
- Added binding file for infineon,cat1-flash-controller.yaml
- Added overlays for subsys/nvs and drivers/flash_shell
to support cy8cproto_063_ble, cy8cproto_062_4343w boards
- Defined erase-block-size in PSoC6 MPN dtsi.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Reworked QDEC SHIM to suppor multi-instance peripheral. Patch includes
Kconfig alignment for proper instance handling.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Although existing nRF SoCs have only one I2S instance, the nrfx_i2s
driver has now multi-instance API and the related nrfx configuration
symbols need to be used appropriately.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add TF-M support for nrf9161 DK and enable it by default for the
non-secure board variant.
Disable UART1 since TF-M use this for output and it is configured
as a secure peripheral.
Enabling this will trigger a BusFault in TF-M.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Print the memory usage of TF-M built executables during build.
This is defaulting to OFF because we have CONFIG_TFM_BUILD_LOG_QUIET
set to ON.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Added a generic driver for RaspberryPi Pico PIO.
This driver is an intermediate driver for abstracting the PIO
device driver from physical pin configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
OpenThread requires that the `mTimestamp` parameter from the `mRxInfo`
struct points to the end of SFD, i.e. beggining of PHR.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
After `otPlatRadioSleep` was fixed to properly set radio state to sleep,
radios supporting `IEEE802154_HW_SLEEP_TO_TX` capability would not be
able to handle `PENDING_EVENT_TX_DONE` while in sleep state.
This commit fixes such case.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
In d540cf8877 I tried to optionally enable the cache management
functions in Open-AMP introducing a new CONFIG_OPENAMP_WITH_DCACHE
symbol.
This is not working. Introduce a proper fix to have this actually
working correctly as intended.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The nRF9161 is technically a SiP (System-in-Package) that consists of
the nRF9120 SoC and additional components like PMIC, FEM, and XTAL,
so for nrfx/MDK the nRF9120 SoC is to be selected as the build target,
but since the nRF9161 is what a user can actually see on a board, using
only nRF9120 in the Zephyr build infrastructure might be confusing.
That's why in the top level of SoC definitions (for user-configurable
options in Kconfig, for example) the nRF9161 term is used and nRF9120
underneath.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Commit adds experimental support mbedtls psa as crypto
backend for ble mesh. It were run only on bsim tests.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Move the Segger RTT module Kconfig to modules/segger/kconfig. The Segger
debug library is not a driver and should not reside under drivers/debug.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
MISRA Rule 5.7 requires uniqueness of tag identifiers. Shell is
frequently problematic because many code uses `const struct shell
*shell`. This causes CI noise every time one of these shell files is
edited, so let's update all of them with `const struct shell *sh`
instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The init infrastructure, found in `init.h`, is currently used by:
- `SYS_INIT`: to call functions before `main`
- `DEVICE_*`: to initialize devices
They are all sorted according to an initialization level + a priority.
`SYS_INIT` calls are really orthogonal to devices, however, the required
function signature requires a `const struct device *dev` as a first
argument. The only reason for that is because the same init machinery is
used by devices, so we have something like:
```c
struct init_entry {
int (*init)(const struct device *dev);
/* only set by DEVICE_*, otherwise NULL */
const struct device *dev;
}
```
As a result, we end up with such weird/ugly pattern:
```c
static int my_init(const struct device *dev)
{
/* always NULL! add ARG_UNUSED to avoid compiler warning */
ARG_UNUSED(dev);
...
}
```
This is really a result of poor internals isolation. This patch proposes
a to make init entries more flexible so that they can accept sytem
initialization calls like this:
```c
static int my_init(void)
{
...
}
```
This is achieved using a union:
```c
union init_function {
/* for SYS_INIT, used when init_entry.dev == NULL */
int (*sys)(void);
/* for DEVICE*, used when init_entry.dev != NULL */
int (*dev)(const struct device *dev);
};
struct init_entry {
/* stores init function (either for SYS_INIT or DEVICE*)
union init_function init_fn;
/* stores device pointer for DEVICE*, NULL for SYS_INIT. Allows
* to know which union entry to call.
*/
const struct device *dev;
}
```
This solution **does not increase ROM usage**, and allows to offer clean
public APIs for both SYS_INIT and DEVICE*. Note that however, init
machinery keeps a coupling with devices.
**NOTE**: This is a breaking change! All `SYS_INIT` functions will need
to be converted to the new signature. See the script offered in the
following commit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
init: convert SYS_INIT functions to the new signature
Conversion scripted using scripts/utils/migrate_sys_init.py.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
manifest: update projects for SYS_INIT changes
Update modules with updated SYS_INIT calls:
- hal_ti
- lvgl
- sof
- TraceRecorderSource
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
tests: devicetree: devices: adjust test
Adjust test according to the recently introduced SYS_INIT
infrastructure.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
tests: kernel: threads: adjust SYS_INIT call
Adjust to the new signature: int (*init_fn)(void);
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
With the stm32h5x, hal driver is xspi for octospi
Add a header file to map functions and constants.
The ospi driver of the stm32H5x serie does not support DMA yet.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit fixed Openthread kconfig option to use correct value and
description of units.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Similar to the changes made in #48048, compile in the appropriate lora
modem driver when `CONFIG_LORA=y`. The `LORA_SX12XX` symbol has no
use now so remove. LoRa and LoRaWAN subsystems are still marked as
unstable so no additional deprecation cycle is needed.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Move tfm_merged.hex from <build>/tfm_merged.hex to
<build>/zephyr/tfm_merged.hex.
Use relative path to the runners.yaml hex file.
This makes it possible to move the build folder.
Example would be to copy out the runners.yaml and tfm_merged.hex file
and still be able to call west flash --skip-rebuild.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
- Added Cmakefiles for modules\hal_infineon\btstack-integration\,
where handle generation of Bluetooth include blob from HCD binary.
- Supported following device/modules:
-- CYW43012/MURATA-1LV module
-- CYW4343W/MURATA-1DX module
-- CYW43439/MURATA-1YN module
-- CYW4373/STERLING-LWB5plus module
- Added possibility to use user provided BT Firmware HCD file via
kconfig (path must be defined in
CONFIG_CYW43XX_CUSTOM_FIRMWARE_HCD_BLOB)
- Updated top makefile
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Enable DMA driver.
Add the path of the DMA driver header into include paths.
`hardware_claim` is depends by DMA driver, also enable it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Product URL: https://www.ti.com/product/CC1352P7
Datasheet : https://www.ti.com/lit/ds/symlink/cc1352p7.pdf
Features:
Powerful 48-MHz Arm® Cortex®-M4F processor
* 704KB flash program memory
* 256KB of ROM for protocols and library functions
* 8KB of cache SRAM
* 144KB of ultra-low leakage SRAM with parity for
high-reliability operation
* Dual-band Sub-1 GHz and 2.4 GHz operation
Updates:
* Remove CC1352P7_LaunchXL due to compliance checks
* Add CC1352P7 updates
* Update hal_ti for CC1352P7 support
* Remove blank line at end of modules/Kconfig.simplelink
* Split struct and typedef for pinctrl_soc_pin/pinctrl_soc_pin_t
* Reference cc13x2_cc26x2/pinctrl_soc.h
* Reference cc13x2_cc26x2/soc.h
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
OPENTHREAD_CONFIG_TCP_ENABLE is now set by the OpenThread build system,
based on the CONFIG_OPENTHREAD_CLI_TCP_ENABLE Kconfig entry.
Setting this symbol in the config file is therefore redundant, and
causes multiple build warnings.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The build will fail if `gpio1` is disabled in an overlay.
For example:
```
&gpio1 {
status = "disabled";
};
```
Signed-off-by: Francois Gervais <francoisgervais@gmail.com>
Add check in CMake files to prevent resource overlap for
TIMER0, TIMER1, RTC0.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
In general, RTC and TIMER driver implements counter API but there
are exception when those peripherals are used in a custom way
(e.g. for system timer or bluetooth). In that case, system must
prevent using counter based on a reserved instance. Previously,
it was managed by Kconfig options but that cannot be maintained
when switching to devicetree configuration of the counter driver.
A new approach removes Kconfig options and instead adds static
asserts in the files which are using direct peripherals. Those
asserts check if given node is not enabled in the device tree.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit enables zephyr to configure the FatFs FF_FS_REENTRANT
option and support fs actions from multiple threads.
CONFIG_FS_FATFS_REENTRANT enables the option and provides zephyr
mutex wrappers.
Signed-off-by: Nicola Ochsenbein <Nicola.Ochsenbein@husqvarnagroup.com>
This commit extends the Zephyr module yaml scheme with additional
entries for sysbuild in the build section.
This allows for Zephyr modules to extend the sysbuild infrastructure
by providing additional CMake and Kconfig files to be included in
sysbuild.
The new settings are:
build:
sysbuild-cmake: <path>
sysbuild-kconfig: <path>/<file>
sysbuild-ext: <true>|<false>
sysbuild-kconfig-ext: <true>|<false>
those settings follow the same pattern as the equivalent Zephyr build
settings but are processed by sysbuild.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Fixes an issue where thread preemption was not being disabled
correctly, failing to taking into account MetaIRQ, which can be
used to preempt any cooperative thread.
The updated code sets the current thread to `K_HIGHEST_THREAD_PRIO`
before calling the secure function, and restores the thread priority
level once secure execution has terminated, allowing the thread
to be preempted once again.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Adding an Openthread radio API `otPlatRadioSetMacFrameCounterIfLarger`
implementation and the corresponding call to the IEEEE802154 driver.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Remove `#include "utils/code_utils.h"` and macros connected with it.
File was incorrectly included in `diag.c` as it is OpenThread's header
used for examples only.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
added `otPlatDiagRadioTransmitCarrier` functionality
disabled OT power calibration support
fixed wrong check of `radio_api->stop()` return value
in `otPlatRadioSleep()`
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
The CANopenNode stack expects registered RX buffers to be processed and
matched in priority order. The priority corresponds to the index of each
each registered RX buffer with lower indexes having higher priority.
Depending on the CANopen COB-ID network configuration used, it may result
in overlapping CAN RX filters. In the case of overlaps, the priorities of
the registered RX buffers matter.
When receiving a CAN frame, process the RX buffers in priority order and
only dispatch the callback for the matching object with the highest
priority.
Fixes: #54364
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Added an option to disable and enable the continuous and optional
carrier functions in the nordic 802.15.4 driver.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
LEGACY_INCLUDE_PATH has been defaulting to "n" and marked as deprecated
in both v3.2 and v3.3. Drop the option entirely for v3.4.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Commit add hidden Kconfig option CONFIG_FS_FATFS_FF_USE_LFN
that is passed to ELM FAT to define FF_USE_LFN configuration.
The FF_USE_LFN still depends, indirectly, on choice
CONFIG_FS_FATFS_LFN_MODE config options
CONFIG_FS_FATFS_LFN_MODE_BSS, FS_FATFS_LFN_MODE_STACK and
FS_FATFS_LFN_MODE_HEAP, but the logic has been moved out of
zephyr_fatfs_config.h into Kconfig file.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
QCBOR cannot be shipped with Zephyr.
Allow the application to supply their own copy of QCBOR or let the TF-M
build system automatically download this dependency.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Prevents Zephyr from enabling the initial attestation service in TF-M,
due to a dependency it has on an incompatibly-licensed library (QCBOR).
This update checks if either of the following config flags are
enabled at build time:
- `CONFIG_TFM_PARTITION_INITIAL_ATTESTATION`
- `CONFIG_TFM_PSA_TEST_INITIAL_ATTESTATION`
If either of these are set to true, a fatal error will be thrown at
build time, indicating the reason for the failure.
This change can be reverted once a longer term solution to the QCBOR
license issues has been resolved.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Add glue code for the thrift module. This includes:
* workarounds for Zephyr's missing C++ facilities
* thrift config.h
This code was merged from the following repository
at the commit specified below, with minor formatting
and coding-style modifications.
https://github.com/zephyrproject-rtos/gsoc-2022-thrift
e12e014d295918cc5ba0b4c507d1bf595a2f539a
Signed-off-by: Chris Friedt <cfriedt@meta.com>
The TF-M platform partition has now been ported to PSA firmware
framework 1.1 and can now be used together with the SFN model.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove setting of the TFM_LIB_MODEL option for IPC and SFN models.
This option is removed together with the library model.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix setting of TF-M floating point options when floating point is
enabled in the application.
FP design in Armv8.0-M architecture requires consistent FP ABI types
between SPE and NSPE.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
remove `CONFIG_OPENTHREAD_RADIO_LINK_IEEE_802_15_4_ENABLE` from
`openthread-core-zephyr-config.h` which is now handled in
`modules/openthread/CMakeLists.tx`
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
Currently if C11 or higher is enabled, many files fail to compile because
static_assert is defined in multiple header files. Solve this by
disabling the one in the HAL if the other macro is found
Signed-off-by: Thad House <thadhouse1@gmail.com>
Add TF-M connection based NCS API source file to build.
This file is needed when a secure service is using connection
based method.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: David Brown <david.brown@linaro.org>
Update TF-M from 1.6.0 to 1.7.0
Update MBedTLS from 3.1.0 to 3.2.1.
Updates the cmake wrapper for changes introduced in TF-M 1.7.0.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: David Brown <david.brown@linaro.org>
In TF-M 1.7.0 release the Library model has been removed.
Remove the library model support from zephyr before updating TF-M
version.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: David Brown <david.brown@linaro.org>
Change from depending on newlib to requiring a full libc, this allows use
with picolibc or any other C library providing a complete implementation.
Signed-off-by: Keith Packard <keithp@keithp.com>
The nRF HW models have been updated to correspond to a 52833 instead
of a 52832. Let's follow them.
The motivation for the change is to enable proper BIS encryption support
(for BT LE Audio ISO).
Changes:
* Point in manifest to latest HW models
* SOC_COMPATIBLE_NRF52832 has been removed, and SOC_COMPATIBLE_NRF52833
added in its place (with no uses at this point)
* Where SOC_COMPATIBLE_NRF52832 was used to set encryption like for a 52832
(to avoid using the MAXPACKETLENGHT), we set the condition to just
SOC_NRF52832.
Note: The MAXPACKETLENGHT register exists in the new simulated nrf52833,
thought it does nothing.
* In the BLE ctrl LLL radio HAL, all macros are renamed accordingly
(timings are NOT changed).
* Board dts definition now refers to the 52833 soc definition. New 52833
features set as not supported by now.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Remove the dependency on the test repositories having a zephyr module
file in their repositories.
With this change we can take the upstream test repositories direct
commit SHA or tag.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This commit updates all deprecated `CONFIG_LIB_CPLUSPLUS` usages to:
* check if the Zephyr minimal C++ library is enabled using
`CONFIG_MINIMAL_LIBCPP` instead of relying on the
`CONFIG_LIB_CPLUSPLUS`-based inference.
* select `CONFIG_REQUIRES_FULL_LIBCPP` when there exists a component-
level C++ standard library dependency. This allows a component to
declare C++ standard library dependency without designating a
specific libray implementation.
* select the correct type of C++ standard library implementation to use
through one of the `CONFIG_LIBCPP_IMPLEMENTATION` choices.
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
This removes the tinycbor module and replaces references in it
e.g. in sample text to use the zcbor replacement.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
The LCG method used earlier in the random number generator was problematic,
as the lowest bits repeated periodically (for example, the generated number
always resulted in an odd-even-odd-even-.. sequence, or the last three bits
formed an cycle of the length 8). This is because the LCG was done module
2^32. Any LCG using a power of 2 as the modulus will cause the same issue.
The used RNG method was changed to Marsaglia's xor shift-algorithm,
which does not have this issue.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
Enabling by default (if SPI3 used) because it affects all revisions
since "Engineering B", including the most recent one as of today
(revision 3).
Size changes when enabled:
- -Og: flash +160 bytes (+0.02%), RAM +8 bytes (+0.01%)
- -Os: flash +144 bytes (+0.02%), no change to RAM usage
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
There were some requests from users for adding the possibility
of setting default openthread tx output power using kConfig.
It is possible by adding the CONFIG_OPENTHREAD_DEFAULT_TX_POWER
kConfig and assigning it to the tx_power variable in the radio.c
file in the Openthread module.
Added the possibility to set default openthread power using
kConfig.
Signed-off-by: Arkadiusz Balys <arkadiusz.balys@nordicsemi.no>
Clean up occurrences of "#if IS_ENABLED(CONFIG_FOO)" an replace
with classical "#if defined(CONFIG_FOO)".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ADC module has four conversion groups, each one is set up as a zephyr
device. The start-up calibration is initiated globally for all groups
and it is run in each device init function. The ADC module supports post
calibration per group. Post calibration is run automatically after each
group acquires the samples.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
The commit applies small changes in ELM FAT driver support code,
required by the driver update to version 0.15.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
In Infineon XMC4XXX SoCs, gpio interrupts are triggered via an
Event Request Unit (ERU) module. A subset of the gpios are
connected to the ERU. The ERU monitors edge triggers and creates
a SR.
This driver configures the ERU for a target port/pin combination
for rising/falling edge events. Note that the ERU module does
not generate SR based on the gpio level. Internally the ERU
tracks the *status* of an event. The status is set on a positive
edge and unset on a negative edge (or vice-versa depending on
the configuration). The value of the status is used to implement
a level triggered interrupt; The ISR checks the status flag and
calls the callback function if the status is set.
The ERU configurations for supported port/pin combinations are
stored in a devicetree file dts/arm/infineon/xmc4xxx_x_x-intc.dtsi.
The configurations are stored in the opaque array
uint16 port_line_mapping[].
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Cortex M0 support was previously disabled due to a compiler bug.
SDK 15.1 includes GCC 12.1 which solves this issue.
Fixes: #52788
Signed-off-by: Jon Escombe <jone@dresco.co.uk>
The Kconfig option allows to set minimum expected sector size
to be supported by FAT fs driver.
When this value differs from CONFIG_FS_FATFS_MAX_SS the driver
will query device for actual sector size, expecting different
sector sizes for different device. When CONFIG_FS_FATFS_MIN_SS
and CONFIG_FS_FATFS_MAX_SS are the same, then there is slight
reduction if FAT driver size, as the query logic is removed
and CONFIG_FS_FATFS_MAX_SS is used for all devices.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Introduce an API mirroring the CMSIS-DSP's basicmath. If CMSIS_DSP is
enabled, then it will by default be used as a backend. Developers may
opt into a custom backend by setting CONFIG_DSP_BACKEND_CMSIS=n. If
done, the application must provide `zdsp_backend/dsp.h` and optionally
implement the functions in its own .c files.
Signed-off-by: Yuval Peress <peress@google.com>
Add CONFIG_CRC for building CRC related routines.
CRC routines are now being built for each application, whether used or
not and are add in the build system unconditionally.
Keep CONFIG_CRC enabled by default for now and until all users have
converted to use the new option.
Partial fix for #50654
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is a follow-up to commit c7327f5f70.
Wrap implementation of the `mbedtls_hardware_poll()` function in
`#if defined(CONFIG_MBEDTLS_ZEPHYR_ENTROPY)` so that the function
is provided only when that option is activated.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The code moves Zephyr specific code and CMakeLists.txt
under modules/fatfs/.
The commit also adds zephyr_fatfs_config.h header file, that
is now used to override FF_ options of ffconf.h file within
fatfs repository.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
net_pkt_get_frag() and a few other functions did not specify the
allocated fragment length, incorrectly assuming that fixed-sized
buffers are always used.
In order to make the function work properly also with variable-sized
buffers, extend the function argument list with minimum expected
fragment length parameter. This allows to use net_buf_alloc_len()
allocator in variable buffer length configuration, as well as verify if
the fixed-sized buffer is large enough to satisfy the requirements
otherwise.
Update the existing codebase to provide the expected fragment length,
based on the context.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Adding module files for building the Arm Ethos-U Core driver.
Updating TFLU module file to build Ethos-U operator.
Adding hal_ethos_u to west manifest.
Signed-off-by: Kristofer Jonsson <kristofer.jonsson@arm.com>
Signed-off-by: Fredrik Knutsson <fredrik.knutsson@arm.com>
Switch to use newest 2.10 API version in nrfx by default.
It changes signature of user callback in the nrfx_ipc driver.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Currently, the nrf-802154-spinel IPC service requires that the IPC
service node has a specific name (ipc0). This makes it impossible to
overwrite the IPC service node to be used by the Spinel serialization
without completely redefining the ipc0 node. Create a `chosen` property
called nordic,802154-spinel-ipc that can be reassigned with any IPC
service node.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
This commit adds API version symbols. The symbol is used in nrfx
drivers, where new API-breaking changes are introduced. Symbol
guards conflicting API.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
hal_nxp was added to cmake's include directories globally, without
checking if the hal is enabled. This made all Zephyr builds end up
including hal_nxp, even for other vendors.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
In order to avoid using multiple sources of truth for the platfom's
endianness, convert the in-tree code to use the (BIG|LITTLE)_ENDIAN
Kconfig variables exclusively, instead of the compiler's
__BYTE_ORDER__.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The can_frame and can_filter structs support a number of different flags
(standard/extended CAN ID type, Remote Transmission Request, CAN-FD format,
Bit Rate Switch, ...). Each of these flags is represented as a discrete bit
in the given structure.
This design pattern requires every user of these structs to initialize all
of these flags to either 0 or 1, which does not scale well for future flag
additions.
Some of these flags have associated enumerations to be used for assignment,
some do not. CAN drivers and protocols tend to rely on the logical value of
the flag instead of using the enumeration, leading to a very fragile
API. The enumerations are used inconsistently between the can_frame and
can_filter structures, which further complicates the API.
Instead, convert these flags to bitfields with separate flag definitions
for the can_frame and can_filter structures. This API allows for future
extensions without having to revisit existing users of the two
structures. Furthermore, this allows driver to easily check for unsupported
flags in the respective API calls.
As this change leads to the "id_mask" field of the can_filter to be the
only mask present in that structure, rename it to "mask" for simplicity.
Fixes: #50776
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Most IEEE 802.15.4 drivers do not support promiscuous mode, some do.
There is a dedicated L2 flag to signal this capability to clients.
Unfortunately the IEEE 802.15.4 L2 stack does not announce this flag
even for drivers that correctly expose it in their HW capabilities.
Some clients (notably the OpenThread L2) even uses promiscuous mode
without checking whether the driver actually supports it.
This change lets the vanilla IEEE 802.15.4 L2 check the driver's
HW capabilities to announce promiscuous mode on its 'get_flags()'
interface if supported.
The OpenThread L2 uses a constant (potentially incorrect) response
to 'get_flags()'. Fixing the OpenThread L2 is out of scope of this
change. This change just introduces TODO messages to the OpenThread code
so that the OpenThread team may fix the issue (or delete the TODO if they
deem it irrelevant).
Fixes: #51263
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
This patch introduces support for NXP S32 devices, specifically for
S32Z27 from S32Z/E family.
NXP S32Z27 processors are composed of two Real-Time Units (RTU)
containing each four ARM Cortex-R52 cores with flexible split/lock
configuration, and dedicated internal SRAM.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Instead of using "select" on certain EC configurations, which is
considered unsafe for various reasons, use a "depends on" and rely on
the user to set a proper configuration in the config file.
Update the respective project configurations to comply with the new
configuration scheme.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
I've update FFF to run tests in the native CI for GitHub, so we no
longer need to run these extra tests. Remove the fff module from
west.yml since the module was only used in the CI and the header
was directly included in the Zephyr tree.
See https://github.com/zephyrproject-rtos/fff/pull/2
Signed-off-by: Yuval Peress <peress@google.com>
Add options about Internal RC(IRC) oscillator.
- GD32_HAS_IRC_32K/40K indicates IRC types.
- GD32_LOW_SPEED_IRC_FREQUENCY is the numeric value of frequency
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add option to enable the SFN model when building TF-M.
The SFN model will eventually replace the Library model.
Change the default model to be IPC, which follows the default
configuration of TF-M.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update the source files compiled when `CONFIG_LORAMAC_REGION_CN470` is
enabled to link. Despite the naming, a `RegionBaseUS.c` function
(`RegionBaseUSVerifyFrequencyGroup`) is used by all four of the CN470
band implementations.
Validated by compiling `samples/subsys/lorawan/class_a` with
`CONFIG_LORAMAC_REGION_CN470` instead of `CONFIG_LORAMAC_REGION_IN865`.
Fixes#49960.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Up until now, the Zephyr CAN controller drivers set a default bitrate (or
timing) specified via devicetree and start the CAN controller in their
respective driver initialization functions.
This is fine for CAN nodes using only one fixed bitrate, but if the bitrate
is set by the user (e.g. via a DIP-switch or other HMI which is very
common), the CAN driver will still initialise with the default
bitrate/timing at boot and use this until the application has determined
the requested bitrate/timing and set it using
can_set_bitrate()/can_set_timing().
During this period, the CAN node will potentially destroy valid CAN frames
on the CAN bus (which is using the soon-to-be-set-by-the-application
bitrate) by sending error frames. This causes interruptions to the ongoing
CAN bus traffic when a Zephyr-based CAN node connected to the bus is
(re-)booted.
Instead, require all configuration (setting bitrate, timing, or mode) to
take place when the CAN controller is stopped. This maps nicely to entering
"reset mode" (called "configuration mode" or "freeze mode" for some CAN
controller implementations) when stopping and exiting this mode when
starting the CAN controller.
Fixes: #45304
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit prioritizes usec timer over msec. Doing so improves
CSL by helping scheduling timeslots on IEEE 802.15.4 with lower miss
rate.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
1. Move the defines from usb_dc_mcux.h to usb_device_config.h
and fsl_os_abstraction.h. These headers are used by
the SDK USB driver. usb_dc_mcux.h header file is not longer
needed and hence deleted.
2. Delete the Zephyr implementation of the usb_device_struct
driver and use the one implemented inside the SDK USB
driver. This requires updating the references to
usb_device_struct inside the USB driver
3. Move defines and structures used by the driver
out of the header file that is included by the SDK and
into the MCUX USB driver.
4. Use end point defines provided by Zephyr instead of adding
them locally.
5. Add a Kconfig to set the thread stack size
6. Move code to enable interrupts back to usb_attach function.
Interrupts should be enabled after the init is successful,
else we see errors of the ISR getting called before the
init is complete causing Faults
6. Update west.yml to update the NXP HAL to get the updated
SDK USB driver.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The commit switches flash area access from FLASH_AREA_ macros
to FIXED_PARTITION_ macros and to usage of DTS node labels,
to identify partitions, instead of label property.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
As of today <zephyr/zephyr.h> is 100% equivalent to <zephyr/kernel.h>.
This patch proposes to then include <zephyr/kernel.h> instead of
<zephyr/zephyr.h> since it is more clear that you are including the
Kernel APIs and (probably) nothing else. <zephyr/zephyr.h> sounds like a
catch-all header that may be confusing. Most applications need to
include a bunch of other things to compile, e.g. driver headers or
subsystem headers like BT, logging, etc.
The idea of a catch-all header in Zephyr is probably not feasible
anyway. Reason is that Zephyr is not a library, like it could be for
example `libpython`. Zephyr provides many utilities nowadays: a kernel,
drivers, subsystems, etc and things will likely grow. A catch-all header
would be massive, difficult to keep up-to-date. It is also likely that
an application will only build a small subset. Note that subsystem-level
headers may use a catch-all approach to make things easier, though.
NOTE: This patch is **NOT** removing the header, just removing its usage
in-tree. I'd advocate for its deprecation (add a #warning on it), but I
understand many people will have concerns.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
LittleFS has some macros resolving to the Zephyr LOG_* ones, use
the ##__VA_ARGS__ for these so that they don't leave a trailing comma if
called with a single argument.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Set OpenThread specific cmake options depending on the selected
device type.
This reduces the number of libraries to build.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
If enabled the optimization is done at the expense of power consumption
on SED/SSED devices.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
In order to ensure that builds properly reflect the use of binary blobs,
it is important to markt the build as tainted. For that purpose
introduce two new Kconfig options that ultimately will be reflected in
the build image itself.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The old project, liblc3codec, is not used anymore. Rename the Zephyr
module name, folders, and Kconfig options based on the new name, liblc3.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Many device pointers are initialized at compile and never changed. This
means that the device pointer can be constified (immutable).
Automated using:
```
perl -i -pe 's/const struct device \*(?!const)(.*)= DEVICE/const struct
device *const $1= DEVICE/g' **/*.c
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
It is frequent to find variable definitions like this:
```c
static const struct device *dev = DEVICE_DT_GET(...)
```
That is, module level variables that are statically initialized with a
device reference. Such value is, in most cases, never changed meaning
the variable can also be declared as const (immutable). This patch
constifies all such cases.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Rename the can_state enumerations to contain the word STATE to make their
meaning more clear:
- CAN_ERROR_ACTIVE => CAN_STATE_ERROR_ACTIVE
- CAN_ERROR_WARNING => CAN_STATE_ERROR_WARNING
- CAN_ERROR_PASSIVE => CAN_STATE_ERROR_PASSIVE
- CAN_BUS_OFF => CAN_STATE_BUS_OFF
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Change sourcing of generated Kconfig.module to be optional.
It should be possible to run parse the Zephyr Kconfig tree even if the
Kconfig.modules file has not been generated.
This can be useful in testing where you may wish to run without Zephyr
modules present, and thus not load the Zephyr module CMake module.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Remove the "z" prefix from the public CAN controller API types as this
makes them appear as internal APIs.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Debug log messages generated by mbedTLS library contain newline at the end
of log string. Remove this newline, if it exists, so that log output is
much more user friendly.
Add a dedicated Kconfig option for that, so it can be disabled on request.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
So far LOG_DBG() was used inside debug hook for mbedTLS library. This meant
that it was hard to distinct log messages by simply looking at the log
level number, even though Zephyr logging subsystem supports colorful logs
depending on log level.
Choose an appropriate Zephyr LOG_*() macro based on log level coming from
mbedTLS library. Remove log level number from formatted log messages, as it
is now redundant.
One controversial thing about this change is that mbedTLS' "2 State change"
log level is mapped to Zephyr's "warning" log level. Those are not really
warnings in real life, but rather informational messages. However, using
"warning" log level for those allows to clearly distinguish between "2
State change" and "3 Informational" debug messages from mbedTLS.
Additionally, mbedTLS debug message implementation does not seem to be safe
to use in production, so keeping in mind MBEDTLS_DEBUG will be enabled just
during debugging phase, printing "2 State change" logs as warnings should
not be a big deal.
Set default MBEDTLS_DEBUG_LEVEL value depending on selected Zephyr logging
module level, so that only single option needs to be configured in
application project.
Remove prompt for MBEDTLS_DEBUG_LEVEL, so that interactively (e.g. via
menuconfig) adjusting MBEDTLS_LOG_LEVEL will always result in automatically
updating MBEDTLS_DEBUG_LEVEL option. This is to prevent so called "stuck
symbol syndrome".
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
So far there was a runtime basename extraction of filenames passed to
mbedTLS debug hook. This has both runtime penalty as well as code size
penalty.
Introduce a buildtime support of extracting basename of source filenames
logged using logging subsystem, so that there is no need to do it at
runtime.
Provide Kconfig options for both buildtime and runtime basename extraction,
as in some cases the buildtime basename extraction might not work,
depending on toolchain used for building Zephyr. Default to buildtime when
using Zephyr SDK, as that is proven to work. Use runtime basename
extraction in other cases (other toolchains used).
This saves approximately 204 bytes of code footprint for sample
application with native TLS sockets built for nRF52840.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
mbedTLS library threshold initialization was done in native TLS socket
implementation (which tends to use mbedTLS now) and inside mbedTLS
benchmark test. Move that to mbedTLS module initialization, as this is a
global setting.
Update description of CONFIG_MBEDTLS_DEBUG_LEVEL to clarify when
mbedtls_debug_set_threshold() is called.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
So far there was a debug log hook installed in TLS socket implementation.
However, mbedTLS (with debug enabled) might be used outside from TLS socket
and even outside from networking context.
Add new module, which implements debug log hook and makes it available
whenever CONFIG_MBEDTLS_DEBUG is enabled.
Note that debug hook needs to be installed for each mbedTLS context
separately, which means that this requires action from mbedTLS users, such
as TLS sockets implementation.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Remove modules/hal_nordic/Kconfig.dt as we now autogenerate the
contents of this file based on the dts bindings in tree.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add module specific compiler flags to suppress reporting unused
variables and unused functions in mbedtls building.
Signed-off-by: Eugene Cohen <quic_egmc@quicinc.com>
Signed-off-by: Dave Aldridge <quic_daldridg@quicinc.com>
Update lvgl for devicetree updates to use zephyr,keyboard-scan.
Remove Kconfig symbol (LV_Z_POINTER_KSCAN_DEV_NAME) that don't exist
anymore since these values are coming from devicetree.
Signed-off-by: Kumar Gala <galak@kernel.org>
Introduce uoscore-uedhoc repository, providing OSCORE and EDHOC
libraries as a new Zephyr module.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Instead of relying on selected ciphesuite to enable mbed TLS EC configs,
add separate config entries to enable them. This allows to use EC
functionality w/o TLS/DTLS enabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
psa_crypto_cipher.c includes an internal header with <>, causing
complication errors in Zephyr (header not found).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The CMP, TMU and SHRTIMER modules were not compiled. Add them now that
GD32E50X series support is being added (this SoC has such units).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add some compile definitions necessary for the gd32e50x HAL and select
default crystal clock.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add `OPENTHREAD_CONFIG_MESSAGE_BUFFER_SIZE` to Kconfig.
Also set the number of children to minumum possible for MTD builds
in order to save some resources (~512B of RAM).
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Use chosen ieee802154 device from DT since
CONFIG_NET_CONFIG_IEEE802154_DEV_NAME is being phased out.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Exclude the non-secure TF-M application from being built by TF-M.
This also stops the building of the tfm_ns_api library that we were
linking against.
This library is defined by the tf-m regression tests.
Add the installed interface source files exported by the TF-M build
system compile them in the zephyr build system.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The OpenThread module should not explicitly link with libc in case of
minimal libc or picolibc.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
LV_Z_DISPLAY_DEV_NAME, LV_Z_HOR_RES_MAX, & LV_Z_VER_RES_MAX
Kconfig symbols don't exist anymore. They got removed in
recent devicetree update of lvgl module. So remove them from
modules/Kconfig.lvgl.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add missing `LV_Z_HOR_RES_MAX`, `LV_Z_VER_RES_MAX`
and `LV_Z_DISPLAY_DEV_NAME`
Kconfig symbols to fix the following Kconfig warnings:
warning: LV_Z_DISPLAY_DEV_NAME defined without a type
warning: LV_Z_HOR_RES_MAX defined without a type
warning: LV_Z_VER_RES_MAX defined without a type
Fixes
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Add a bunch of missing "zephyr/" prefixes to #include statements in
various test and test framework files.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Zephyr kernel is dependent on trace.
Trace is dependent on segger rtt.
Segger rtt MUST NOT be dependent on zephyr kernel.
Move lock functions from header into c file to avoid circular
dependency. This fix needs an update of the segger repository.
Fixes#43887.
Signed-off-by: Christoph Coenen <ccoenen@baumer.com>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
With support for deprecating Kconfig symbols within the Kconfig tree
itself, there is no reason to have a secondary location to maintain
for information that is based on a Kconfig setting in first place.
Better to directly do `select DEPRECATED` on the symbol itself, than to
maintain a secondary list with messages in CMake.
Hence removing this feature in CMake.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Move scripts needed by the build system and not designed to be run
individually or standalone into the build subfolder.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move OpenThread's glue code along with the Kconfig files that configure
OpenThread stack itself into module directory.
Update the maintainers file to reflect this change.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Move to use DEVICE_DT_GET_ONE instead of device_get_binding as
we work on phasing out use of DTS 'label' property.
Signed-off-by: Kumar Gala <galak@kernel.org>
According to mbedTLS' Changelog "Mbed TLS 3.0.0 branch released
2021-07-07" -> "Removals":
MBEDTLS_ECP_MAX_BITS is no longer a configuration option because it
is now determined automatically based on supported curves.
Hence remove MBEDTLS_ECP_MAX_BITS from configuration files to fix build
issues with Zephyr when there is unfortunate order of include
statements.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Zephyr adds a custom handler that overrides the weak function
sys_arch_reset when TF-M platform partition is enabled.
This takes away the option for the application to override the weak
definition for their platform or use-case.
Add an option that control whether this default reset handling is added
to the build.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Allow the application to enable the FPU when TF-M has been enabled.
Pass the correct compilation flags according to the TF-M integration
guide.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
There is a compiler bug in the current Zephyr SDK (GCC 10.3.0) that
prevents using LVGL on ARM Cortex M0/M0+. Disable LVGL on such CPU until
the next SDK is deployed (GCC 12.1), as the issues does not appear
anymore.
Ref. https://github.com/lvgl/lvgl/issues/3425
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
A recent change to hal_rpi_pico's cmake, intended to fix the
compilation via Unix Makefiles, ended up not linking the BL
to the final ELF. This commit fixes both problems.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
This code has gone unmaintained and bugs continue to be reported
against it. We do not have the resources as a project to maintain this
in "odd fixes" mode, and nobody has stepped up to maintain it [1], so
sadly this must be removed for now.
If anyone would like to see civetweb supported in upstream Zephyr
again, they are welcome to add it back, as long as they promise to
maintain it going forward.
Many thanks to everyone who has contributed to civetweb support in
Zephyr while it was here. So long and thanks for all the fish.
Fixes: #45807Fixes: #43910Fixes: #34226Fixes: #46743
[1] https://lists.zephyrproject.org/g/devel/message/8466
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Stop relying on <soc.h> to access HAL APIs. Use generic, per-API headers
instead. Note that <soc.h> has been left as is for now, since ARM MPU
relies on a fragile chain of includes/type definitions.
This change should improve compilation efficiency, as we no longer pull
APIs that are not needed. A similar approach is followed by STM32
drivers.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
When the SYS_CLOCK_EXISTS Kconfig option is not enabled, k_busy_wait()
has no implementation, so in such case, call nrfx_coredep_delay_us()
directly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Before mbedTLS 3.0 there was just SHA512 option, which enabled both SHA384
and SHA512 support. mbedTLS 3.0 introduced SHA384 specific option, which
means that SHA384 got unsupported after merging
commit 4e6cfb67f9 ("modules: mbedTLS: Bump mbedTLS to 3.0").
Introduce SHA384 Kconfig options, so that support for it can be selected in
project configuration if needed. Since SHA384 still depends on SHA512 to be
selected, add such dependency in Kconfig.
Select SHA384 support in non-generic (not configured by Kconfig) mbedTLS
config headers, so that previous (before mbedTLS 3.0 was merged) behavior
is regained.
Fixes: 4e6cfb67f9 ("modules: mbedTLS: Bump mbedTLS to 3.0")
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
This module has gone unmaintained and we do not have the resources to
respond to bug reports for it.
The TSC has decided to deprecate it for Zephyr v3.1 and remove it
entirely in Zephyr v3.2 unless a maintainer volunteers to keep this
module up to date and fix bugs.
This commit generates a warning at CMake time if this module is
compiled in. The warning will appear in the cmake output in the same
place that deprecated board or SoC warnings would.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We currently have mechanisms for deprecating both boards and SoCs.
However, we lack one for deprecating modules. This is inconvenient,
because we would like to do exactly that.
Handle this in a simple way by adding a new CMake file in the modules
directory which is responsible for warning the user about any
deprecated modules they may be using. See the source code comments for
more details about the approach.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
RPi Pico second stage bootloader generation seems to fail when using
Makefiles with:
gmake[2]: *** No rule to make target 'bootloader/boot_stage2.S'...
Changing the ExternalProject_Add byproduct to the actual generated file
and not the .S seems to fix the problem.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This reverts commit 619fce9e0f now that
the missing PRIuFAST32 and PRIxFAST32 macros are defined by the minimal
libc.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Problem:
pull/43494 is causing the CMake warning
No SOURCES given to Zephyr library: modules_hal_infineon
modules_hal_infineon library was defined even if none of the
below subdirectories is added; so, when not building for
Infineon/Cypress devices, the source list for this library
will be empty.
Fix:
Added 'zephyr_library_named(modules_hal_infineon)' under condition
'if(CONFIG_HAS_XMCLIB OR CONFIG_SOC_FAMILY_PSOC6)'
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Refactor iMX RT pin control support to use more generic names, as the
IOMUXC peripheral is present on non RT iMX application cores.
Additionally, make selection of the pin control driver occur at the SOC
level.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Previously val_nspe.a, pal_nspe.a, test_combine.a created under tfm binary
directory (${TFM_BINARY_DIR}/app/psa_api_tests/) now from TFM 1.6 it is
generated to the respective tfm binary directory with parent directory
(${TFM_BINARY_DIR}/tf-m-tests/app/psa_api_tests), update the CMake
accordingly.
Signed-off-by: Rajkumar Kanagaraj <rajkumar.kanagaraj@linaro.org>
Refactor help text for TFM_FLASH_MERGED_BINARY to use the standard
indentation of tab plus 2 spaces.
Reword BUILD_WITH_TFM default comment, TF-M is enabled by default, not
forced enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert the can_mode enum to a bit field to prepare for future extensions
(CAN-FD mode, transmitter delay compensation, one-shot mode, 3-samples
mode, ...).
Rename the existing modes:
- CAN_NORMAL_MODE -> CAN_MODE_NORMAL
- CAN_SILENT_MODE -> CAN_MODE_LISTENONLY
- CAN_LOOPBACK_MODE -> CAN_MODE_LOOPBACK
These mode names align with the Linux naming for CAN control modes.
The old CAN_SILENT_LOOPBACK_MODE can be set with the bitmask
(CAN_MODE_LISTENONLY | CAN_MODE_LOOPBACK).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Current Espressif porting requires standard include as
part of hal implementation. compiler_flags.cmake checks for
variant name to keep those stdinc in build.
Instead of using variant name as check, use this new CONFIG
to make it clear and to allow having toolchain integrated
in zephyr-sdk package.
stdinc dependency in hal_espressif will be worked out and removed
soon.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
In order to bring consistency in-tree, migrate all modules code to the
new prefix <zephyr/...>. Note that the conversion has been scripted,
refer to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
On non Linux system, the compilation failed because the main
CMake did not pass the CMAKE_SYSTEM_NAME to the bootloader's
CMake. This caused the variable to be empty, instead of being
"Generic".
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
This commit adds the missing common tables dependency for the SVM
functions.
The `exp_tab` and `exp_tab_f16` tables are required by the SVM
functions when the MVE is enabled.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The `CMSIS_NN` Kconfig previously depended on the `CMSIS_DSP` Kconfig,
and this placed the "CMSIS-NN Library Support" prompt under the "CMSIS-
DSP Library Support" menu (note that CMSIS-DSP is a menuconfig).
Since the CMSIS-NN library, although it requires the CMSIS-DSP library,
is not a subordinate component of the CMSIS-DSP library, remove its
dependency on `CMSIS_DSP` and make it select the Kconfig symbol
instead.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Because Minimal LIBC doesn't have PRIuFAST32 and PRIxFAST32 which is
needed when printing traces in zcbor.
Signed-off-by: Øyvind Rønningstad <oyvind.ronningstad@nordicsemi.no>
Add Kconfig configuration options which allow to configure
session caching in mbed TLS.
Note, that mbed TLS only takes care of server-side caching, the
application (socket layer) needs to implement a session storage for
client.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add Kconfig options to enable/disable features that are exposed in zcbor
via ZCBOR_ macros that are typically set via -D statements to the
toolchain.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Support for the can_get_max_filters() API function is optional and may
not be supported by all drivers.
The check for an adequate amount of filters is just there in order to
fail early. If the driver does not support can_get_max_filters(),
reporting of a failure will be delayed until a filter addition fails.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add initial build rules for CHRE. This change includes a Kconfig and
CMakeLists.txt to begin compiling code from the CHRE module.
Additional files are included to bridge the APIs from CHRE's to
Zephyr's. These can be found in modules/chre/include and
modules/chre/src.
Additionally, add a sample to make sure that the module builds. It can
be built via:
```
$ west build -b native_posix -p=always samples/application_development/chre
```
Signed-off-by: Yuval Peress <peress@google.com>
Previously, MCUBOOT_DATA_SHARING was enabled when BL2 was built
and when the firmware update partition was present. This is not
the only situation that you might be interested in this data
sharing. The data sharing now has it's own Kconfig.
Further, use of the firmware update partition requires data
sharing, so it selects it.
Signed-off-by: Jimmy Brisson <jimmy.brisson@linaro.org>
Previously, you were required to set the image versions through the
CMake variables TFM_IMAGE_VERSION_{S,NS}. For better integration with
the rest of the zephyr build system, these are now KConfig variables
with the same name.
Signed-off-by: Jimmy Brisson <jimmy.brisson@linaro.org>
This commit adds a sample application demonstrating how to use
the PSA Firmware Update API from TF-M. It also enables the
`FIRMWARE_UPDATE` partition to be included at build time.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Signed-off-by: Jimmy Brisson <jimmy.brisson@linaro.org>
Add a Kconfig to disable non prefixed includes. By setting
`CONFIG_LEGACY_INCLUDE_PATH=n` developers can disable having
`include/zephyr` in the search path. This means that includes such
as `#include <kernel.h>` will no longer work.
Internally, every header should be updated to add the `zephyr/`
prefix to the headers. Only then, will developers be able to use
this config value for their applications.
Signed-off-by: Yuval Peress <peress@google.com>
Move include paths and add new target_include_directories to support
backwards compatibility:
* /include -> /include/zephyr
example: <irq.h> -> <zephyr/irq.h>
Issue #41543
Signed-off-by: Yuval Peress <peress@google.com>
See #40591 for details, TinyCBOR (or rather the fork of TinyCBOR that we
had) is being replaced by zcbor.
Closes#40591.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add configuration for BL2 not supported. In some configurations
BL2 will not be supported. Provide a way to deselect BL2 support.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Change dependencies of the Kconfig options that enable particular nrfx
drivers so that the drivers and their instances are available when
a devicetree node with a corresponding compatible property exists,
no matter if it is enabled or not.
Change the options that enable compilation of multi-instance drivers
to be promptless helpers only (not directly configurable for users),
as they need to be enabled only together with some options that enable
particular instances of a given driver, and those options select them
as needed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fix crash in TF-M when non-secure IRQ is interrupting the secure
processing and using the FPU.
The FPU context must be saved when
ARM_NONSECURE_PREEMPTIBLE_SECURE_CALLS is disabled since an IRQ handler
can still access the FPU registers.
Fixes: #43587
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Initial addition of the LC3 codec as a module. Usage of the module
will be seperate commits.
Even though this codec is a generic audio codec, it is tagged with
Bluetooth: as it can only be used for LE-Audio. Using the codec for
other purposes is a violation of the granted rights for the codec.
Signed-off-by: Casper Bonde <casper_bonde@bose.com>
The purpose of this change is to allow to enable more than one
backend at once by removing choice from ipc-service backend Kconfig
and depending backend Kconfig option on existing of correct compatible.
Overwriting IPC_SERVICE_BACKEND option in some places is removes
as no longer needed.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Fix TF-M nonsecure interface dispatch handling when calling secure
service before the kernel is fully active.
This fixes crash in nordicsemi_nrf53_init, which is called with
PRE_KERNEL_1, when calling soc_secure_gpio_pin_mcu_select.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The CANopenNode stack does not support CAN-FD. Depend on it being
disabled and explicitly disable it in the CANopenNode sample.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The filter in the testcase.yaml made it impossible for these to run.
Also, the Kconfig names for the options didn't really make much sense
so they were renamed to avoid conflict.
This fixes an issue found by #36433.
Signed-off-by: Yuval Peress <peress@google.com>
The intialization level of 802.15.4 on NET core was set to APPLICATION,
which caused some applications to break during initialization. Changed
it to POST_KERNEL. CONFIG_NRF_802154_SER_RADIO_INIT_PRIO default value
was adjusted.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
Include a pointer to the CAN controller device for the CAN
transmit, receive, and state change callback functions.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Support function and data lookup in the RPi's ROM.
The objects are obtained by including <pico/bootrom.h> and calling
rom_func_lookup or rom_data_lookup.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Instead of including from nrfx_glue.h a specific Zephyr Bluetooth
controller header file that defines PPI and GPIOTE resources to be
reserved for exclusive use by the controller, include a file with
only a fixed name and expect the chosen Bluetooth controller to
provide the location of this file in include paths. This way, when
a different Bluetooth controller implementation is used downstream,
a different file can be easily pointed to.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for TF-M and BL2 image size reports.
This adds the following targets when TF-M or BL2 is enabled:
tfm_rom_report, tfm_ram_report, tfm_footprint
bl2_rom_report, bl2_ram_report, bl2_footprint
Example:
west build -t tfm_rom_report
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In upstream the LV_COLOR_DEPTH_BITS option is called LV_COLOR_DEPTH, this
needs changing if we want to support v8.2.0.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Add KConfig symbols to select power management HAL drivers required for low
power modes. Set ZTEST_NO_YEILD if PM is enabled, since RT series SOCs
do not connect to a debugger in WAIT mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Currently if an attempt to disable CSMA-CA in by setting an
appropriate flag in another (for example application)
CmakeLists.txt it caused lots of warnings. This fix allows
higher level CMakeLists.txt to disable CSMA-CA without
warnings.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
This commit moves openthread CMakeLists.txt from openthread submodule
to zephyr/modules/openthread.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Fixes: #40559
Moving CMakeLists.txt gluecode into Zephyr repo minimizes the patching
needed in LittleFS repo.
It provides a dedicate Zephyr LFS config header which will define the
equivalent LittleFS settings based upon Kconfig settings.
This further reduces the patching needed in LittleFS.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
LittleFS requires a `lfs_crc()` function, however the basic crc
function provided by LittleFS gets disabled when a custom configuration
header is used.
To ensure identical crc behavior let Zephyr have a copy of the basic
lfs_crc.
This allows to ensure identical behavior when moving glue code into
Zephyr repo, and allow us to change to an existing crc implementation
provided natively by Zephyr at a later time.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
There are several Kconfig symbols defined in the lvgl module that are
referenced from various defconfigs in the zephyr tree. If the LVGL module
is unavailable, they need to be redefined as stubs in Kconfig.lvgl.
Fixes: 6c190292c0 ("lvgl: move the lvgl glue out of the zephyr tree")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
The nrf_802154_lp_timer_zephyr.c platform file is unused in the
opensource SL library variant.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Start using the upstream Kconfig from LVGL and move the glue code out
of the zephyr tree and put it under lvgl/zephyr/ in modules.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
Change the CPU_CORTEX_R kconfig option to CPU_AARCH32_CORTEX_R to
distinguish the armv7 version from the armv8 version of Cortex-R.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
Parameter `prio` of `nrf_802154_irq_init` is now allowed to have
negative value what means use of ZLI priority or highest possible
priority if ZLIs are disabled.
Signed-off-by: Andrzej Kuros <andrzej.kuros@nordicsemi.no>
Add config to disable all TF-M output. This configuration is needed
in order to exclude the UART driver through a select in Kconfig
when either the code size optimization or the UART instance requires it.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Added basic support for the RP2040 SoC. Support
includes booting and starting the kernel, on one
core only.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This update updates the TraceRecorder module from version v4.5.2
to v4.6.0(RC1). The primary motivation for this update is to
fix some breaking trace hook changes introduced into Zephyr
v2.7.99, which resulted in compilation errors when using the
TraceRecorder module.
The update to v4.6.0 also introduce Snapshot tracing support,
extended kernel object naming, and a reworked configuration
scheme with better naming and layout in guiconfig.
Signed-off-by: Torbjörn Leksell <torbjorn.leksell@percepio.com>
Use the set of headers that the TF-M build system places in the
install output. Not all public header files are available in the
interface/include directory and the TF-M build system uses the install
mechanism of cmake to include additional headers based on platform
or configuration.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
MCUX usb ISR was making usb callbacks directly, which caused assertion
failures when a callback attempted to lock a mutex. Move USB callback
handler to separate thread, and make ISR notify thread via message
queue.
Fixes#40638
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The CAN_BUS_UNKNOWN CAN controller state is only used to indicate that
the current CAN controller state could not be read.
Remove it and change the signature of the can_get_state() API function
to return an integer indicating success or failure.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
GPC driver is used for power management operations on RT series SoCs.
Enable inclusion of the driver into the build.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Provide a _ns target for b_u585i_iot02a board.
Flash partition is given as default for most applications,
with the following sizes:
MCUBoot: 208K
Secure: 256K
Non secure: 512K
Tested using tfm_ipc sample.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
For functions returning nothing, there is no need to document
with @return, as Doxgen complains about "documented empty
return type of ...".
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Increase the default CANopenNode stack sizes a bit. The current stack
sizes are too small for e.g. ST STM32F3, likely other platforms as well.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add Kconfig option for indicating that a given SoC contains the NXP
MCAN CAN FD controller.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Rename a few CAN API functions for clarity and consistency with other
Zephyr RTOS APIs.
CAN_DEFINE_MSGQ() becomes CAN_MSGQ_DEFINE() to match K_MSGQ_DEFINE().
can_attach_isr() becomes can_add_rx_filter() since a filter callback
function is not an interrupt service routine (although it is called in
isr context). The word "attach" is replaced with "add" since filters are
added, not attached. This matches the terminology used is other Zephyr
APIs better.
can_detach() becomes can_remove_rx_filter() to pair with
can_add_rx_filter().
can_attach_msgq() becomes can_add_rx_filter_msgq() and documentation is
updated to mention its relationship with can_add_rx_filter().
can_register_state_change_isr() becomes can_set_state_change_callback()
since a state change callback function is not an interrupt service
routine (although it is called in isr context). The word "register" is
replaced with "set" since only one state change callback can be in
place.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit aligns nrf_802154_lp_timer_zephyr platform to new API of
nrf_rtc_timer. Moreover, it implements lp_timer synchronization
functions using the new nrf_rtc_timer API.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Signed-off-by: Paweł Kwiek <pawel.kwiek@nordicsemi.no>
In TF-M 1.5 some defaults changed. Some of our CMake code was
unfortunately making assumptions about the defaults.
This is now rectified. The TF-M CMake variables that had their
defaults changed are now always set dependent on the Kconfig values
and we no longer leave the CMake variables unset and with default
values.
A cleanup will be done later to not rely on default values for all
variables. This patch only fixes the defaults that have changed.
Also, TFM_PSA_API is removed as it is now an internal variable.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Change the can_tx_callback_t function signature to use an "int" (not an
uint32_t) for representing transmission errors.
The "error" callback function parameter is functionally equivalent to
the return value from can_send() and thus needs to use the same data
type and needs to be able to hold negative errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit aligns nrf_802154_lp_timer_zephyr platform to new API of
nrf_rtc_timer. Moreover, it implements lp_timer synchronization
functions using the new nrf_rtc_timer API.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Signed-off-by: Paweł Kwiek <pawel.kwiek@nordicsemi.no>
This patch restricts access of CCA configuration related macros to
builds for which nRF 802.15.4 Radio Driver is enabled. This reduces
clutter and prevents misuse of CCA macros.
Signed-off-by: Paweł Kwiek <pawel.kwiek@nordicsemi.no>
Add two Kconfig variables for controlling the size and
the number of assets to be stored in Internal Trusted
Storage (ITS).
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
Fix copy-paste mistake in SPM log level silence configuration, PARTITION
should be SPM in order to correctly silence SPM log.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Deprecate the use of CAN-specific error return values and replace them
with standard errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
MBEDTLS_ECP_MAX_BITS is now set automatically by mbed TLS, redefining it
in the config file ends up in compilation warnings.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Adds a driver using the SNVS high power and optionally low power
RTC instances. A device specific function `mcux_snvs_rtc_set` is
provided to update the current counter value.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Switch from using can_configure() to using can_set_mode() for disabling
CAN controller transmissions.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move all defines that specifies (D)PPI resources which are used
to dedicated files which have no include dependencies. This allow
to use them in nrfx_glue.h to specify fixed (D)PPI channels used
by the bluetooth.
Additionally, added mask with GPIOTE channels used by the bluetooth
controller. It was previously not defined which could lead to
conflicts since same channels could be allocated by the nrfx_gpiote
user
Updated nrfx_glue.h to use new approach.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Set NRF_SKIP_FICR_NS_COPY_TO_RAM for nrf53 and nrf91 until corresponding
memory region is excluded from use.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Update the hal_nordic module revision, to switch to nrfx v2.6.0.
nrfx 2.6.0 includes extended API in nrfx_gpiote which can be
used by the zephyr shim.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Mcuboot's bootutil libraries has option to use hooks which
allows to customize its behavior while proceeding on images
date. This patch introduces configuration options required for
enabling that option.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Use nrfx_gpiote and nrfx_ppi allocators to allocate channels
at runtime instead of fixed, device-tree based allocation which
is harder to maintain.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds UCPD HAL and LL drivers to the Kconfig system
required to enable USB Power Delivery interface (UCPD)
on STM32G0/G4/L5/U5 devices
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
The TFM build directory path is hardcoded in many places.
In order to support out-of-tree secure partitions the output path
has to be known in potentially out-of-tree build scripts.
This could potentially break out-of-tree build scripts if the
location of the build directory was changed.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add a pin control driver for GD32 SoCs using the AFIO model.
Thanks to Gerson Fernando Budke for testing and implementation
suggestions.
Co-authored-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Fix issue with TFM signing of images not using the correct imgtool.
The wrapper command expects the mcuboot scripts folder to be the
current working directory when called in order to find its own
version of imgtool.
Since the command is using a different current working directory
this is not found and the system imgtool is used instead.
This causes the commands to be run with 2 different version of imgtool
if the system imgtool is found and does not have any issues.
The system imgtool could not be installed or have compatibility issues
as 1.7.2 version of imgtool is currently required by the wrapper script
Fixes: #40254
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This rework module hal_gigadevice to be compliance with rule
that requires firmware libraries directories names be lowercase.
This rule was created at hal_gigadevice/README and it is not
a Zephyr general rule. This only affect how hal_gigadevice is
used.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
GD32F4XX requires access to SoC definitions (e.g. GD32F450) when
including library header files, so expose them at Zephyr level.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Fix cmake warnings for TF-M build system when PSA tests are not enabled.
This produces the following warnings:
"
CMake Warning:
Manually-specified variables were not used by the project:
PSA_TOOLCHAIN_FILE
TOOLCHAIN
"
These warnings can point to cache or config variables being updated in
the TF-M build system so keep this free of warnings.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update crypto modules prompt strings to follow the Kconfig guidelines.
"For a Kconfig symbol that enables a driver/subsystem FOO, consider
having just “Foo” as the prompt, instead of “Enable Foo support” or the
like."
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The ASSYMETRIC crypto module has been split in two, for sign and
encrypt. Update Kconfig entries to match.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove CRYPTO_GENERATOR_MODULE Kconfig which has been removed.
Its features are covered by TFM_CRYPTO_KEY_MODULE and
CRYPTO_KEY_DERIVATION_MODULE.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Set a thread name for the tx_workq thread, so that it shows up in
"kernel stacks" when the shell or thread debugging are enabled.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
So far maximum PSK length was configured by mbedTLS as 32 bytes.
Introduce Kconfig option that will configure it instead of relying on
default value from mbedTLS library, so that user can easily adjust that
value to application needs.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Split the zephyr project maintained repository trusted-firmware-m into
forks of the individual upstream repositories.
https://git.trustedfirmware.org/TF-M/trusted-firmware-m.git
Upstream: TF-Mv1.4.1
Additions:
zephyr: module: Add zephyr module file
trusted-firmware-m: platform: lpcxpresso55s69: Update SDK
https://git.trustedfirmware.org/TF-M/tf-m-tests.git
Upstream: 51ff2bdfae043f6dd0813b000d928c4bda172660
Additions:
zephyr: module: Add module file for tf-m-tests
https://github.com/ARM-software/psa-arch-tests.git
Upstream: 60faad2ead1b967ec8e73accd793d3ed0e5c56bd
Additions:
zephyr: module: Add module file for psa-arch-tests
psa-arch-tests: Allow overriding of toolchain file
The organization of folders remain the same with the following
exceptions:
Moved:
root folder moved from modules/tee/tfm to modules/tee/tf-m to avoid
problems with west update.
zephyr/module.yml to trusted-firmware-m/zephyr/module.yml and
${ZEPHYR_TRUSTED_FIRMWARE_M_MODULE_DIR} points to what was previously
${ZEPHYR_TRUSTED_FIRMWARE_M_MODULE_DIR}/trusted-firmware-m.
Added:
psa-arch-tests/zephyr/module.yml and ${ZEPHYR_PSA_ARCH_TESTS_MODULE_DIR}
tf-m-tests/zephyr/module/ and ${ZEPHYR_TF_M_TESTS_MODULE_DIR}
Removed:
init-git.sh
README.rst
Fixes: #39353
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use the zephyr module dir variable for the trusted-firmware-m root
folder. Update documentation to TF-M documentation in
tfm-secure-boot.rst.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The previous CONFIG_CAN_MAX_FILTER is specific to certain drivers.
Using the new API makes the CAN open driver independent of the used
CAN hardware / driver.
Signed-off-by: Martin Jäger <martin@libre.solar>