Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ifd65097a65f80539cac073f95aadc2d8e42efb9f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This extends the pwm_dw sample app to build for
FRDM_K64F board also. Because of this, pwm_dw
has been renamed to pwm.
This allows us to put it through sanity test
to catch build breakage.
Change-Id: Ie4d7442af43ede58f4cec0ec28643384a685321a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ifdbb5e3a997795ef577350d88f8cb06877eb6463
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib8158f00a6c6616360ddbcf63981f1a85911c1b9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
On Galileo Gen2 board SPI uses GPIO pin for CS.
Thus spi_intel driver must be initialized after gpio_dw,
so it's init level must be more that gpio_dw's one.
Change-Id: If2e5fb1106afe01e5567cf3fe72063bdc94ad3d2
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
GCC enables unaligned memory access for ARMv6 and above.
Once unaligned memory access is allowed, there's no need
for the unaligned memory access trap.
The change prevents the situation when the compiler
generates code that uses unaligned memory access, but
the CPU generates an exception when this code runs.
Change-Id: Id33f2264c631772e5c561e76fb579d8b7bc26e1e
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
This patch extends the i2c shim driver so it supports the 'default
configuration' infrastructure which enables the user to specify a
default configuration for the I2C device. The default configuration
is set during driver initialization.
This patch also changes Quark SE and D2000 Kconfig.defconfig files so
the i2c default configuration is set to '0x12' which means standard
bus speed, 7-bit addressing and master mode. This is the same value
used when DW driver is selected, by the way.
Change-Id: I06e0dc3c29e8da2f3317db5bef285177f2e92c9a
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This adds the necessary tags to enable building the grove_lcd and
i2c_fujitsu_fram sample apps, so that the Atmel SAM3 I2C driver
will be built to test for build breakage.
Change-Id: I4adfb6336e82a6d407bbd5e9888c27d5f6bc5be1
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove those kconfig options that are SoC specific, and should not be
configurable via kconfig.
Change-Id: Ia62888838877da4627419bd36c261d5254761acd
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
It wasn't correct to add the size of the long jump instruction
as it *replaces* a short jump instead of just being after it.
So redefine this to be the difference in size between these
two instructions.
Change-Id: I65be2afab19d9cd8b096551acde0156f0503df87
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Reduces the amount of memory allocated for fiber's stack.
This permits the test_nano to compile on boards like
nucleo-f103rb and arduino 101 sss. Sanitycheck script passes
all test for test-fifo.
This patch was verified on the emulated platforms and not against
real hardware boards.
Change-Id: Icf30c4056d9f9ebdc82c100305bf761e49b64491
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Zephyr now uses codes from errno.h as the standard returning code for
all APIs. Since some code usages can be confusing or ambiguous, this
patch documents the conventions we are using to keep the returning code
usage consistent.
The document is based on the current mapping we have in device.h.
Change-Id: Ie6f429602592be8572631e34ae65435530a05b9f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Each option within Kconfig.qmsi already set its dependency so this
patch removes the 'if I2C_QMSI' block since it is redundant.
Change-Id: Ic221b96766ecac685491cb31525caf28e641ee45
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Reduces the amount of memory allocated for fiber's stack.
This permits the test to compile on boards like
nucleo-f103rb and arduino 101 sss.
Sanitycheck script passes all test for test-lifo.
This patch was verified on the emulated platforms and not
against real hardware boards.
Change-Id: I1dd514c9d273bcf490e0eb4f1fadee1a8a94bcc5
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Current interrupt status tells which pins triggered this interrupt, thus
the handler should acknowledge only these and not all possible, since we
don't know if other gpio controller interrupts are being taken care of
at the same moment.
Change-Id: I7d3f1bb13bb293f7b7ce9b5a717a37bbdd4e4e42
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
These interrupt settings are SOC specific. So, move them to the
SOC level of Kconfig.
As IRQ priority is fixed in D2000, changed the value to 0 to
make it consistent with what other shim drivers are using.
Change-Id: Id20bed46c478a7555ae976e3a3063ba2cb099788
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This will improve the speed when flashing an image to the board:
before:
downloaded 4936 bytes in 7.982860s (0.604 KiB/s)
after:
downloaded 4936 bytes in 4.486743s (1.074 KiB/s)
Change-Id: I0209d53ba15dbf8e3f16e2d3675a35b58342776a
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is hardware design so there is no need for it to be
configurable in kconfig.
Change-Id: Iff162f330aae8ef9a7139b6e7ed9bfa87f26189a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There is no need to re-define CONFIG_UART_CONSOLE_ON_DEV_NAME to be
"UART_0" all over the place as its default is "UART_0" already.
So remove those duplicate defaults.
Change-Id: Ia86e26b8f90540fdbd7dcb3358d6dac352648b21
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The IRQ triggering condition should be specified by SoC as it is
a decision for hardware design. This should not be configurable
in kconfig.
The default is to be triggered on rising edge, just as the same
old kconfig did.
Change-Id: If59d88a30711eb8e03d9cc4f409055cefe1995c5
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Moves those kconfig options which should be declared in
SoC or board header files instead. These are the one
that are tied to SoC or board and there is no need
for them to be configurable in kconfig.
Change-Id: I243d634f1a4a11dc8dc3530d95f93371015492b7
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The extended inquiry response data format include at least two octets:
length and type, so adding NULL termination name shall be 240-2+1
octets.
Fixes accessing wrong memory in the statement below:
...
memcpy(name, &eir[2], sizeof(name) - 1);
...
Change-Id: I71be96aed6af63d0649f4d64271208eeb11e2c6c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This patch fixes drain of data left in UART Rx fifo.
uart_irq_tx_ready checks if Rx IRQ has been raised,
but because Rx IRQ is disabled this won't work even
if there are some data left in the UART buffers.
So simply uart_fifo_read is used to discard the data that
left in UART buffer.
Change-Id: I17f145ba58640650bafd3602412fc75229f39664
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
These tests were using non-portable NANO_CPU_INT_REGISTER. They
now use IRQ_CONNECT, which lets us run these tests on all arches
and not just x86.
Change-Id: Idd4264c2650c851aa78356f01586edbadd014501
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The script will now run under either Python 2 or Python 3.
Change-Id: Ia7e6647b2331ff9edfbdec7b7357439f7095a3bc
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The PWM_QMSI_DEV_NAME and PWM_QMSI_NUM_PORTS options depend on PWM_QMSI
already so this patch removes the 'if PWM_QMSI' block since it is
redundant.
Change-Id: Iec303d27f088b96662fc58933eaa82fe9459cb59
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Fixes this built error:
zephyr/drivers/pinmux/quark_mcu/pinmux_board_quark_se_dev.c:149:19:
error: 'PINMUX_BASE_ADDR' undeclared (first use in this function)
_pinmux_defaults(PINMUX_BASE_ADDR);
Change-Id: I8302e4d6dbcf961e0c80f6bccf740a877bb364af
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use SPI_0 by default or SPI_1 if configured differently.
Change-Id: I63f39f63a4b70fded3a7af8061058ba4779e573e
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This file was misplaced here. Atom board is now available only
for minnowboard.
Change-Id: If5a0d723600f957e2b024848b8cb8aac2e7a7ff9
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
lp_count register can be store directly to memory, it is actualy done,
and the instruction that precedes it has no effect.
Change-Id: I8b8fee6abd6f08eea38dd1ab5bbe61c25a2a1f7d
Signed-off-by: Alexandre d'Alton <alexandre.dalton@intel.com>
ARC CPU has stack checking feature that allows to trigger an exception
whenever the stack is incorrectly accessed.
This patch implements the stack_top and stack_base register updates on
context switches, and activates the Stack Checking bit of STATUS32
register when the CPU is in the context of a fiber or task.
As GCC accesses the non-yet allocated stack with frame pointer enabled,
this patch also add the omit-frame-pointer gcc flag in order to work
properly.
Change-Id: Ia9e224085a03bd29d682fb8f51f8e712f2ccb556
Signed-off-by: Alexandre d'Alton <alexandre.dalton@intel.com>
The base addresses are SoC specific so there is no need to make
configurable via kconfig.
Change-Id: Iaf8444f77513255d5f0112af6710243aae09f066
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the #ifdef are not really needed, so clean up the file
for readability.
Change-Id: I4d15f3cb7ef4db9113d4cdadbd3309da6587c64e
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: Iab10655c6fc6f17c0c6dd49cb7a4e74fabcf852c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: I3a51b35e633dc7b1b841e9fa504bf0cfc0d4d575
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to standardize the kconfig for specifying IRQ priority.
Change-Id: I05ae4033e2c5431ba2727c5d4000ef07e14739c8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The pinmux base address and number of pins are now defined in SoC or board
header files instead of specifying them in kconfig. This is because
the pinmux ties directly to the SoC (or board expanders) so the base
address and number of pins do not need to be configurable in kconfig.
Change-Id: Ib6090d7d022b491f3fe8f522858281504c6302bb
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is to follow how kconfig are defined for other SoC/boards.
Origin: refactored from exising file
Change-Id: Ic83b8a336f1910f17b3cf4e7f029fd076ba1b6bb
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The base address, IRQ line, chip select numbers, and clock
gating constants are static per SoC, so there is no need to
make them configurable in Kconfig.
Change-Id: I9f87ca29c28c38c42d4e4f1a3a41fa231f63ef03
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
