This adds a new config option for SAM0 targets that use the BOSSA
bootloader. If the CDC ACM driver is also enabled, then the
programmer can automatically reset the board into the bootloader for
programming.
Signed-off-by: Michael Hope <mlhx@google.com>
This is called when the USB host changes the virtual baud rate.
This is used by Arduino style boards to signal that the board should
reset into the bootloader.
Signed-off-by: Michael Hope <mlhx@google.com>
The wdt CLEAR register is a write synchronized register.
To avoid bus stall, check the status of SYNCBUSY before
accessing the register.
Use SYNCBUSY register for SAM E.
If the wdt is syncing, return -EAGAIN to avoid bus stall.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
One of the interrupts used by the gen_isr_table test conflicts with a
gpio interrupt on the lpc54114 soc, so disable gpio for this test on the
corresponding board. We do this for only the m4 core because the test is
not supported on the m0 core.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
extended download progress metrics to Bytes, KiB and MiB
separate number of download iterations for INF and numeric case
Signed-off-by: Alexander Kozhinov <AlexanderKozhinov@yandex.com>
Add support to STM IIS2DH the ultra-low-power highperformance
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add option to concatenate i2c transfers. If concatenation buffer size is
provided then transfers will be concatenated as long as there is space
left in buffer.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Added a build-time assert to check if heap memory configuration to
make sure that it can accomodate RPMsg queue allocations.
Ref: NCSDK-5479
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
nucleo_f767zi with soc cut-A (Device marking A) has some ethernet
restrictions.
Use of cut-Z is adviced.
fixes#26519
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
In case of control register lock, driver should return the error
immediately. Otherwise, error is later overwritten by
'rc = flash_stm32_wait_flash_idle(dev);'
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
ep_idx is common used designator for endpoint index,
rename ep_num to ep_idx in usb_dc_sam0 driver.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This commit adds a dependency on the TRNG resource in the TI Power
module, prevents the system policy from entering standby when TRNG is
active, and adds support for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Commit 269f350487 introduced a new
mechanism for loading the edtlib.EDT representation of the devicetree
from kconfigfunctions.py.
While this works for running kconfig.py from kconfig.cmake using
execute_process(), it doesn't work when kconfigfunctions.py is loaded
by the menuconfig target or any other Kconfig targets that use
add_custom_target().
The reason why is that these targets' environments do not have the
location of the EDT pickle file available. This is unlike kconfig.py,
which executes using the same environment as cmake itself, where
edt.pickle's location is already available in the environment.
Fix that by adding EDT_PICKLE to the environment for menuconfig and
friends.
Reported-by: Simon Guinot <simon.guinot@seagate.com>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Commit ef3c5e5516 changed the way
WEST_TOPDIR is initialized from calling 'west topdir' as a subprocess
to using the west API.
However, WEST_TOPDIR is a cmake variable and must be a cmake-style
path, with forward slashes. While 'west topdir' as a command does
output a forward slash separated path (basically in order to make the
zephyr build system work), west_topdir() as an API returns the path in
the host environment path style, which on Windows uses backslashes.
This turns out to be the ultimate cause of the following build error:
CMake Error at C:/.../CheckCCompilerFlag.cmake:41 (set):
Syntax error in cmake code when parsing string
-fmacro-prefix-map=C:\Users\Marti\zp=WEST_TOPDIR
Fix it by converting to POSIX style in Python. We could have
potentially also done this using file(TO_CMAKE_PATH "${WEST_TOPDIR}"
...), but I'm intentionally repeating the old way of doing things
since it was known to work.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Abort I2C transfers through the MCUX HAL if a transfer fails to avoid
deadlock in the driver/HAL.
Fixes#25098
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
restore how --only-failed works by allow rebuilds in case of build
errors, however, do not rebuild when --retry-failed is used, which is a
CI usecase and nothing would change in the second iteration.
Fixes#26685
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The board has a SPI NOR flash enabled by default but was missing
the "zephyr,flash-controller" in DTS. This prevents the flash
shell sample to compile. So add the DTS entry.
Fixes#26764
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The `TEXT_SECTION_OFFSET` symbol is used to specify the offset between
the beginning of the ROM area and the address of the first ROM section.
This commit renames `TEXT_SECTION_OFFSET` to `ROM_START_OFFSET` because
the first ROM section is not always the `.text` section.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Change sets default value of Kconfig option BT_CTLR_LLCP_CONN to
BT_MAX_CONN. The default value should properly handle the worst case.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Fix missing recalculation of skip value of the ticker being
inserted into ordered list, when it collides and is being
attempted to be inserted at next periodic interval.
This fix is for ticker compatibility mode which is used as
default for nRF51 series.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Currently there is a single function that handles both Configure-Ack and
Configure-Rej messages. This is obviously wrong for Configure-Rej,
because implementation applies options received in the message.
Remove Configure-Rej callback, so those frames are simply ignored for
the time no valid handling code exists.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Update the hal_nordic module revision to include the following commits:
- CMakelists: missing "src" in one path
- nrfx_glue: Fix NRFX_PPI_GROUPS_USED_BY_BT_CTLR definition
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update hal_stm32 module in master manifest to include
latest changes around License information
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Cleans up the lpcxpresso55s16 board.cmake to make it consistent with
other lpc boards. jlink.board.cmake sets the default runner to jlink if
not already set.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Cleans up the frdm_k82f board document to make its usage of
zephyr-app-commands consistent with other frdm boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The OPENSDA_FW and LPCLINK_FW cmake variables are remnants of pre-west
days where we used an environment variable to set the desired debug host
tool, such as jlink or pyocd, based on which debug probe firmware was
loaded on the board. We now have two possible ways to do this, neither
of which requires the nxp-specific OPENSDA_FW or LPCLINK_FW variables:
1. Set standardized cmake runner variables when generating the build
system:
$ west build -- -DBOARD_FLASH_RUNNER=jlink -DBOARD_DEBUG_RUNNER=jlink
2. Use the west "--runner" argument with the debug and flash commands:
$ west debug -r jlink
Remove the now unnecessary OPENSDA_FW ond LPCLINK_FW variables and
update board documentation accordingly.
A few boards (frdm_kw41z, hexiwear_k64, mimxrt10{20,50,60,64}_evk)
reordered pyocd.board.cmake and jlink.board.cmake includes to preserve
the default runner when OPENSDA_FW was not explicitly set.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Removes unused instances of struct usdhc_priv in the nxp usdhc driver.
The DISK_ACCESS_USDHC_INIT macro is responsible for instantiating these
variables.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Updates the nxp usdhc driver data structure to keep a reference instead
of a copy of the constant config structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the source clock frequency variable in the nxp usdhc driver from
the config structure to the data structure in preparation for removing
the writable copy of the config structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the nxp usdhc driver to remove instance-specific conditionals
from driver functions. Now all instance-specific details, such as power
and card detect gpios, are contained in the driver config structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds idle wait callback to proxy by counting the number of pending
notifications.
Ensures that all connected nodes have received messages before resetting
the mesh stack.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Reset gpio is configured during driver initialization. There is no
reason to do it repeat that process later, so replace
gpio_pin_configure() with gpio_pin_set().
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Introduce sx1276_configure_pin() helper macro, which hides lots of
boilerplate preprocessor and C code. Doing so allows to uncover
inconsistent gpio initialization flow and prevent such in future. Also
add error log whenever gpio_pin_configure() fails.
It seems like output of gpio_pin_configure() for several
gpios (antenna_enable, rfi_enable, rfo_enable) was assigned to variable,
but its values was never checked. Return value from gpio_pin_configure()
of tcxo_power gpio was even not catched. The only output gpio
configuration that was handled properly was actually reset gpio.
Fix that inconsistent behavior by always checking return value of
sx1276_configure_pin().
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Added initialization of ids fields in the log message in
z_log_msg_std_alloc(). If user space is enabled then msg_free()
function is reading log level and previously it may have been
uninitialized.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Clear negotiated options in protocol down handler. That way all
addresses are properly requested (by sending 0.0.0.0 in Configure-Req)
in the subsequent option negotiation phases.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Fix flash operation timeout due to incorrect use of
secondary ticker to abort any radio in use. Ticker id 0
is reserved for split controller's pipeline preempt timeout.
Using the same ticker id caused the secondary ticker to
not be started if controller is using the same ticker id
for pipeline preempt timeout.
Fixes#26333.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
