LPC55xxx SoCs don't allow reading erased areas, the flash memory
controller (FMC) will trigger an ECC error for that area. To prevent
reading unwritten areas the low level FMC command of margin checking is
used, this will fail if the area to be read is not correctly written
(margin_check) or area is erased (blank_check).
In the case of an erased page, we return dummy data so the application
can program that area.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
With addition of flash_parameters structure, and supporting API call
to retrieve it, it is no longer needed to store write_block_size as
a part of flash_driver_api and it should be part of flash_parameters.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
With addition of flash_get_parameters API call, it is needed to provide
support for the API to flash drivers.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
The soc_flash_mcux supports several possible compatible so handle that
as part of how we set DT_DRV_COMPAT.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_FLASH_WRITE_BLOCK_SIZE with new DT_INST_NODE_HAS_PROP and
DT_INST_PROP macro as we phase out DT_FLASH define usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of DT_FLASH_DEV_NAME with DT_INST_LABEL in drivers as we
want to phase out DT_FLASH_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
move flash.h to drivers/flash.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert generic FLASH_ERASE_BLOCK_SIZE to driver specific generated
define DT_SOC_NV_FLASH_0_ERASE_BLOCK_SIZE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Updates the MCUXpresso SDK to version 2.5.0 for applicable SoCs.
Wireless (KW*) and legacy (KL25) SoCs were not included in this
MCUXpresso SDK release and are therefore not updated here.
New in this release is SoC-level and board-level support for external
xip flash in the i.MX RT family.
For RT1050, we are now using the MCUXpresso SDK for the EVKB version of
the board, which correponds to an upgrade from A0 to A1 silicon.
However, we don't yet have Kconfigs in place to support A1 silicon part
numbers, and therefore add a simple cmake hack to convert A0 part
numbers to A1 part numbers.
The SDK flash driver interface also changed slightly in this release,
and thus the zephyr flash shim driver is updated accordingly.
Origin: MCUXpresso SDK
License: BSD 3-Clause
URL: mcux.nxp.com
Purpose: Provide device header files and bare metal peripheral drivers
for Kinetis, LPC, and i.MX SoCs.
Maintained-by: External
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
irq_lock returns an unsigned int, though, several places was using
signed int. This commit fix this behaviour.
In order to avoid this error happens again, a coccinelle script was
added and can be used to check violations.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
- There is a mismatch when interfacing with external code where a
uint32_t is defined as a parameter and internal Zephyr code attempts
to use u32_t. If NewLib is used, the typedef for u32_t is
'unsigned int' which is not a portable match to uint32_t as
'unsigned int' is not a common size across architectures so gcc will
output a warning.
- The mcux flash code calls NXP supplied functions that expect a
uint32_t.
- openthread.c ot_state_changed_handler has a uint32_t flag as a
parameter.
Signed-off-by: David Leach <david.leach@nxp.com>
Write protection is currently not supported by the mcux flash
driver. This prevents it from working with the DFU subsystem, which
checks the error codes from the write protect routine. Hack it for now
with a semaphore.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Uses the new flash erase-block-size dts property to implement the flash
page layout api in the mcux flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some drivers doesn't implement flash API page layout extension
which is causing the application crash once the API was calling.
This patch introduce system termination for this in those drivers
which doesn't implement extension. This will help to discover this
problem early.
It is not done by preprocessor check because it is possible to have
enabled a driver which support and a driver which doesn't support
this API simultaneously.
Now FLASH_PAGE_LAYOUT configuration option is accessible only in case
that at last one driver which implements mentioned API is enabled.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Write-block-size values were filled for nRF5, STM32, QMSI, MCUX and
w25qxxdv devices.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The newer version of mcux changes its flash api slightly, so update the
Zephyr shim accordingly.
Change-Id: I0c974fc3e82b9f40372c636f0b805ed143be2198
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>