x86_64 doesn't use devicetree, so put some hand-coded definitions
into arch.h to allow it to use the DT-enabled HPET driver.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The GNU ARM Embedded "8-2019-q3-update" toolchain
erroneously uses "typeof" instead of "__typeof__".
To work around this we define typeof to be able to
support it.
This reverts commit 01a71eae3d.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Some DWARF symbols for members of template classes members such as
numeric_limits<unsigned int> reference are static constexpr values
that do not have a data member location. Avoid attempting to
dereference the value for that attribute when it isn't present.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Enabling of testing/default impacts all PR CIs. There isn't that much
extra value for all PRs to have both native_posix and native_posix_64.
Go with native_posix, since most targets are 32-bit on Zephyr.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In some hardware, e.g. ARC HS Development kit,the peripheral
space of DesignWare SPI only allowes WORD access,
byte acess will raise bus error.
This commit adds support for this case
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
* add pinmux driver. hsdk board has arduino, mikrobus and
pmod interfaces, which can be confiured for different function,
such as: gpio, spi, uart, iic.
* add introduction for arduino, mikrobus and pmod interfaces.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Add some mbedTLS tweaks for OpenThread in overlay-ot.conf.
Add sample configuration to enable Commissioner/Joiner, disabled by
default.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
So far OpenThread compiled it's own, internal copy of mbedTLS library.
This commit changes this behavior by using Zephyr's mbedTLS instance
appropriately configured for OpenThread needs.
Generic mbedTLS config file was used in this case, so that application
can still configure remaining parts of mbedTLS for it's own needs.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
OpenThread tweaks some specific mbedTLS configs for it's own need, that
allows to save some RAM/ROM. Allow to set these in generic config file
if OpenThread is enabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Remove FRDM-K64F board config and overlay from cfb_shell sample.
Enable test for the shield ssd1306_128x32.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Suppress integer overflow warning generated by the check macros
NEG_CHECK and ROLLOVER_CHECK in intmath tests
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Removed redundant linker flag --coverage from native posix
EXTRA_LDFLAGS.
The correct linker flags will be set by defining the Kconfig flag
CONFIG_COVERAGE, either by sanitcheck it self or via the test/sample
prj.conf.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
This makes the identity initialization consistent and actually catches
a few branches where it may not have properly happened.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Make it possible to initiate new connections from within the
disconnect callback. This wasn't completely trivial since there was
connection cleanup done through deferred action using the CONN_CLEANUP
flag.
This patch moves the disconnected callbacks to be run after all
cleanup is done. We can't directly do this in the TX thread, since
that's internal, so we instead take advantage of the deferred work
support and do it using the update_work callback. Since the same
cleanup is needed also for BR/EDR connections the work definition is
moved from the LE-specific struct to the generic struct bt_conn.
A valid bt_conn object in disconnected state is a likely indication of
a connection reference leak, so there's a new BT_WARN() for this case
in bt_conn_create_le().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Get these ci-tools commits into CI runs:
- Commit 3a08069 ("check_compliance.py: pylint: Detect Python files not
ending in .py")
- Commit 2184bb4 ("check_compliance.py: Fix formatting mess-up for
error messages")
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
It was reported in the code coverage report that Z_SYSCALL_HANDLER() was
not called by other code, if we run "sanitycheck -p qemu_x86 --coverage
-T tests/kernel/device/".
The root cause is that we include "errno.h", which includes
"include/generated/syscalls/device.h". It causes that the
declare of device_get_binding() in "include/generated/syscalls/device.h"
is marked as "has been called", rather than Z_SYSCALL_HANDLER()
in device.c.
So I remove "#include <errno.h>", which is useless in device.c. Also,
"#include <sys/util.h>" is removed for the same reason.
Signed-off-by: Steven Wang <steven.l.wang@linux.intel.com>
A Kconfig boolean is added to allow users to provide their own
output strings when running tests via ztest.
This allows changing e.g. the PASS/FAIL/SKIPPED strings,
add counters, change separators, and similar.
A test using the feature and relevant documentation is added.
Signed-off-by: Torstein Grindvik <torstein.grindvik@nordicsemi.no>
Adds additional model callback that gets called on node_reset. Will also
erase any user data when this happens.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Adds user data file in the model settings, allowing each model instance
to store some application specific data without having to reinvent the
settings path encoding for model element/ID combinations. Exposes the
settings_handler interface in the model callback structure and adds a
data store function.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Adds a structure of callbacks for each model instance. This allows for
more flexible model implementations, that can interact with the Mesh
stack without going through the application.
For now, only an init callback is added, replacing the init mechanism in
the foundation models. The init callback does not provide the primary
flag that used to be in the foundation model callbacks, but replaces
this with an inline function in access.h.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
