michaelh/zephyr
1
0
Fork 0
Code Releases Activity
zephyr/soc/arm/st_stm32/stm32f4/dts_fixup.h

311 lines
17 KiB
C
Raw Normal View History

license: cleanup: add SPDX Apache-2.0 license identifier Update the files which contain no license information with the 'Apache-2.0' SPDX license identifier. Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of Zephyr, which is Apache version 2. Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2019-04-06 09:08:09 -04:00
/* SPDX-License-Identifier: Apache-2.0 */
drivers: flash: stm32: Convert to use device tree Convert STM32 flash drivers to use device tree to get the flash controller name and base address. Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2018-01-19 14:58:39 -06:00
/* SoC level DTS fixup file */
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_NUM_IRQ_PRIO_BITS DT_ARM_V7M_NVIC_E000E100_ARM_NUM_IRQ_PRIORITY_BITS
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOA_BASE_ADDRESS DT_ST_STM32_GPIO_40020000_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOA_CLOCK_BITS_0 DT_ST_STM32_GPIO_40020000_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOA_CLOCK_BUS_0 DT_ST_STM32_GPIO_40020000_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOA_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40020000_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOA_LABEL DT_ST_STM32_GPIO_40020000_LABEL
#define DT_GPIO_STM32_GPIOA_SIZE DT_ST_STM32_GPIO_40020000_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOA_CLOCK_BITS DT_ST_STM32_GPIO_40020000_CLOCK_BITS
#define DT_GPIO_STM32_GPIOA_CLOCK_BUS DT_ST_STM32_GPIO_40020000_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOB_BASE_ADDRESS DT_ST_STM32_GPIO_40020400_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOB_CLOCK_BITS_0 DT_ST_STM32_GPIO_40020400_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOB_CLOCK_BUS_0 DT_ST_STM32_GPIO_40020400_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOB_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40020400_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOB_LABEL DT_ST_STM32_GPIO_40020400_LABEL
#define DT_GPIO_STM32_GPIOB_SIZE DT_ST_STM32_GPIO_40020400_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOB_CLOCK_BITS DT_ST_STM32_GPIO_40020400_CLOCK_BITS
#define DT_GPIO_STM32_GPIOB_CLOCK_BUS DT_ST_STM32_GPIO_40020400_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOC_BASE_ADDRESS DT_ST_STM32_GPIO_40020800_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOC_CLOCK_BITS_0 DT_ST_STM32_GPIO_40020800_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOC_CLOCK_BUS_0 DT_ST_STM32_GPIO_40020800_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOC_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40020800_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOC_LABEL DT_ST_STM32_GPIO_40020800_LABEL
#define DT_GPIO_STM32_GPIOC_SIZE DT_ST_STM32_GPIO_40020800_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOC_CLOCK_BITS DT_ST_STM32_GPIO_40020800_CLOCK_BITS
#define DT_GPIO_STM32_GPIOC_CLOCK_BUS DT_ST_STM32_GPIO_40020800_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOD_BASE_ADDRESS DT_ST_STM32_GPIO_40020C00_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOD_CLOCK_BITS_0 DT_ST_STM32_GPIO_40020C00_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOD_CLOCK_BUS_0 DT_ST_STM32_GPIO_40020C00_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOD_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40020C00_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOD_LABEL DT_ST_STM32_GPIO_40020C00_LABEL
#define DT_GPIO_STM32_GPIOD_SIZE DT_ST_STM32_GPIO_40020C00_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOD_CLOCK_BITS DT_ST_STM32_GPIO_40020C00_CLOCK_BITS
#define DT_GPIO_STM32_GPIOD_CLOCK_BUS DT_ST_STM32_GPIO_40020C00_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOE_BASE_ADDRESS DT_ST_STM32_GPIO_40021000_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOE_CLOCK_BITS_0 DT_ST_STM32_GPIO_40021000_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOE_CLOCK_BUS_0 DT_ST_STM32_GPIO_40021000_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOE_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40021000_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOE_LABEL DT_ST_STM32_GPIO_40021000_LABEL
#define DT_GPIO_STM32_GPIOE_SIZE DT_ST_STM32_GPIO_40021000_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOE_CLOCK_BITS DT_ST_STM32_GPIO_40021000_CLOCK_BITS
#define DT_GPIO_STM32_GPIOE_CLOCK_BUS DT_ST_STM32_GPIO_40021000_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOF_BASE_ADDRESS DT_ST_STM32_GPIO_40021400_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOF_CLOCK_BITS_0 DT_ST_STM32_GPIO_40021400_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOF_CLOCK_BUS_0 DT_ST_STM32_GPIO_40021400_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOF_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40021400_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOF_LABEL DT_ST_STM32_GPIO_40021400_LABEL
#define DT_GPIO_STM32_GPIOF_SIZE DT_ST_STM32_GPIO_40021400_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOF_CLOCK_BITS DT_ST_STM32_GPIO_40021400_CLOCK_BITS
#define DT_GPIO_STM32_GPIOF_CLOCK_BUS DT_ST_STM32_GPIO_40021400_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOG_BASE_ADDRESS DT_ST_STM32_GPIO_40021800_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOG_CLOCK_BITS_0 DT_ST_STM32_GPIO_40021800_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOG_CLOCK_BUS_0 DT_ST_STM32_GPIO_40021800_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOG_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40021800_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOG_LABEL DT_ST_STM32_GPIO_40021800_LABEL
#define DT_GPIO_STM32_GPIOG_SIZE DT_ST_STM32_GPIO_40021800_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOG_CLOCK_BITS DT_ST_STM32_GPIO_40021800_CLOCK_BITS
#define DT_GPIO_STM32_GPIOG_CLOCK_BUS DT_ST_STM32_GPIO_40021800_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOH_BASE_ADDRESS DT_ST_STM32_GPIO_40021C00_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOH_CLOCK_BITS_0 DT_ST_STM32_GPIO_40021C00_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOH_CLOCK_BUS_0 DT_ST_STM32_GPIO_40021C00_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOH_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40021C00_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOH_LABEL DT_ST_STM32_GPIO_40021C00_LABEL
#define DT_GPIO_STM32_GPIOH_SIZE DT_ST_STM32_GPIO_40021C00_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOH_CLOCK_BITS DT_ST_STM32_GPIO_40021C00_CLOCK_BITS
#define DT_GPIO_STM32_GPIOH_CLOCK_BUS DT_ST_STM32_GPIO_40021C00_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOI_BASE_ADDRESS DT_ST_STM32_GPIO_40022000_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOI_CLOCK_BITS_0 DT_ST_STM32_GPIO_40022000_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOI_CLOCK_BUS_0 DT_ST_STM32_GPIO_40022000_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOI_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40022000_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOI_LABEL DT_ST_STM32_GPIO_40022000_LABEL
#define DT_GPIO_STM32_GPIOI_SIZE DT_ST_STM32_GPIO_40022000_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOI_CLOCK_BITS DT_ST_STM32_GPIO_40022000_CLOCK_BITS
#define DT_GPIO_STM32_GPIOI_CLOCK_BUS DT_ST_STM32_GPIO_40022000_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOJ_BASE_ADDRESS DT_ST_STM32_GPIO_40022400_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOJ_CLOCK_BITS_0 DT_ST_STM32_GPIO_40022400_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOJ_CLOCK_BUS_0 DT_ST_STM32_GPIO_40022400_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOJ_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40022400_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOJ_LABEL DT_ST_STM32_GPIO_40022400_LABEL
#define DT_GPIO_STM32_GPIOJ_SIZE DT_ST_STM32_GPIO_40022400_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOJ_CLOCK_BITS DT_ST_STM32_GPIO_40022400_CLOCK_BITS
#define DT_GPIO_STM32_GPIOJ_CLOCK_BUS DT_ST_STM32_GPIO_40022400_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOK_BASE_ADDRESS DT_ST_STM32_GPIO_40022800_BASE_ADDRESS
#define DT_GPIO_STM32_GPIOK_CLOCK_BITS_0 DT_ST_STM32_GPIO_40022800_CLOCK_BITS_0
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOK_CLOCK_BUS_0 DT_ST_STM32_GPIO_40022800_CLOCK_BUS_0
#define DT_GPIO_STM32_GPIOK_CLOCK_CONTROLLER DT_ST_STM32_GPIO_40022800_CLOCK_CONTROLLER
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_GPIO_STM32_GPIOK_LABEL DT_ST_STM32_GPIO_40022800_LABEL
#define DT_GPIO_STM32_GPIOK_SIZE DT_ST_STM32_GPIO_40022800_SIZE
dts_fixups: Use DT_ prefix in all defined labels not related to Kconfig These changes were obtained by running a script created by Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following specification: 1. Read the contents of all dts_fixup.h files in Zephyr 2. Check the left-hand side of the #define macros (i.e. the X in #define X Y) 3. Check if that name is also the name of a Kconfig option 3.a If it is, then do nothing 3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it has neither of these two prefixes 4. Replace the use of the changed #define in the code itself (.c, .h, .ld) Additionally, some tweaks had to be added to this script to catch some of the macros used in the code in a parameterized form, e.g.: - CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS - CONFIG_UART_##idx##_TX_PIN - I2C_SBCON_##_num##_BASE_ADDR and to prevent adding DT_ prefix to the following symbols: - FLASH_START - FLASH_SIZE - SRAM_START - SRAM_SIZE - _ROM_ADDR - _ROM_SIZE - _RAM_ADDR - _RAM_SIZE which are surprisingly also defined in some dts_fixup.h files. Finally, some manual corrections had to be done as well: - name##_IRQ -> DT_##name##_IRQ in uart_stm32.c Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
2018-11-13 15:15:23 +01:00
#define DT_GPIO_STM32_GPIOK_CLOCK_BITS DT_ST_STM32_GPIO_40022800_CLOCK_BITS
#define DT_GPIO_STM32_GPIOK_CLOCK_BUS DT_ST_STM32_GPIO_40022800_CLOCK_BUS
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2C_1_BASE_ADDRESS DT_ST_STM32_I2C_V1_40005400_BASE_ADDRESS
#define DT_I2C_1_EVENT_IRQ_PRI DT_ST_STM32_I2C_V1_40005400_IRQ_EVENT_PRIORITY
#define DT_I2C_1_ERROR_IRQ_PRI DT_ST_STM32_I2C_V1_40005400_IRQ_ERROR_PRIORITY
i2c: Rename CONFIG_I2C_[0..5]_NAME -> DT_I2C_[0..5]_NAME Now that everything is DT based for I2C drivers we can rename the CONFIG_I2C_[0..5]_NAME define to DT_I2C_[0..5]_NAME. Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-22 09:38:21 -05:00
#define DT_I2C_1_NAME DT_ST_STM32_I2C_V1_40005400_LABEL
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2C_1_EVENT_IRQ DT_ST_STM32_I2C_V1_40005400_IRQ_EVENT
#define DT_I2C_1_ERROR_IRQ DT_ST_STM32_I2C_V1_40005400_IRQ_ERROR
#define DT_I2C_1_BITRATE DT_ST_STM32_I2C_V1_40005400_CLOCK_FREQUENCY
#define DT_I2C_1_CLOCK_BITS DT_ST_STM32_I2C_V1_40005400_CLOCK_BITS
#define DT_I2C_1_CLOCK_BUS DT_ST_STM32_I2C_V1_40005400_CLOCK_BUS
#define DT_I2C_2_BASE_ADDRESS DT_ST_STM32_I2C_V1_40005800_BASE_ADDRESS
#define DT_I2C_2_EVENT_IRQ_PRI DT_ST_STM32_I2C_V1_40005800_IRQ_EVENT_PRIORITY
#define DT_I2C_2_ERROR_IRQ_PRI DT_ST_STM32_I2C_V1_40005800_IRQ_ERROR_PRIORITY
i2c: Rename CONFIG_I2C_[0..5]_NAME -> DT_I2C_[0..5]_NAME Now that everything is DT based for I2C drivers we can rename the CONFIG_I2C_[0..5]_NAME define to DT_I2C_[0..5]_NAME. Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-22 09:38:21 -05:00
#define DT_I2C_2_NAME DT_ST_STM32_I2C_V1_40005800_LABEL
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2C_2_EVENT_IRQ DT_ST_STM32_I2C_V1_40005800_IRQ_EVENT
#define DT_I2C_2_ERROR_IRQ DT_ST_STM32_I2C_V1_40005800_IRQ_ERROR
#define DT_I2C_2_BITRATE DT_ST_STM32_I2C_V1_40005800_CLOCK_FREQUENCY
#define DT_I2C_2_CLOCK_BITS DT_ST_STM32_I2C_V1_40005800_CLOCK_BITS
#define DT_I2C_2_CLOCK_BUS DT_ST_STM32_I2C_V1_40005800_CLOCK_BUS
#define DT_I2C_3_BASE_ADDRESS DT_ST_STM32_I2C_V1_40005C00_BASE_ADDRESS
#define DT_I2C_3_EVENT_IRQ_PRI DT_ST_STM32_I2C_V1_40005C00_IRQ_EVENT_PRIORITY
#define DT_I2C_3_ERROR_IRQ_PRI DT_ST_STM32_I2C_V1_40005C00_IRQ_ERROR_PRIORITY
i2c: Rename CONFIG_I2C_[0..5]_NAME -> DT_I2C_[0..5]_NAME Now that everything is DT based for I2C drivers we can rename the CONFIG_I2C_[0..5]_NAME define to DT_I2C_[0..5]_NAME. Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-22 09:38:21 -05:00
#define DT_I2C_3_NAME DT_ST_STM32_I2C_V1_40005C00_LABEL
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2C_3_EVENT_IRQ DT_ST_STM32_I2C_V1_40005C00_IRQ_EVENT
#define DT_I2C_3_ERROR_IRQ DT_ST_STM32_I2C_V1_40005C00_IRQ_ERROR
#define DT_I2C_3_BITRATE DT_ST_STM32_I2C_V1_40005C00_CLOCK_FREQUENCY
#define DT_I2C_3_CLOCK_BITS DT_ST_STM32_I2C_V1_40005C00_CLOCK_BITS
#define DT_I2C_3_CLOCK_BUS DT_ST_STM32_I2C_V1_40005C00_CLOCK_BUS
#define DT_I2S_1_BASE_ADDRESS DT_ST_STM32_I2S_40013000_BASE_ADDRESS
#define DT_I2S_1_IRQ_PRI DT_ST_STM32_I2S_40013000_IRQ_0_PRIORITY
#define DT_I2S_1_NAME DT_ST_STM32_I2S_40013000_LABEL
#define DT_I2S_1_IRQ DT_ST_STM32_I2S_40013000_IRQ_0
#define DT_I2S_1_CLOCK_BITS DT_ST_STM32_I2S_40013000_CLOCK_BITS
#define DT_I2S_1_CLOCK_BUS DT_ST_STM32_I2S_40013000_CLOCK_BUS
drivers: i2s: change the stm32 DMA in the driver to use dts This commit moves DMA parameters previously hard coded in the driver to the dts. Signed-off-by: Song Qiang <songqiang1304521@gmail.com> Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-24 15:57:17 +08:00
#define DT_I2S_1_DMA_CONTROLLER_TX \
DT_ST_STM32_I2S_40013000_TX_DMAS_CONTROLLER
#define DT_I2S_1_DMA_CHANNEL_TX DT_ST_STM32_I2S_40013000_TX_DMAS_CHANNEL
#define DT_I2S_1_DMA_SLOT_TX DT_ST_STM32_I2S_40013000_TX_DMAS_SLOT
#define DT_I2S_1_DMA_CHANNEL_CONFIG_TX \
DT_ST_STM32_I2S_40013000_TX_DMAS_CHANNEL_CONFIG
#define DT_I2S_1_DMA_FEATURES_TX \
DT_ST_STM32_I2S_40013000_TX_DMAS_FEATURES
#define DT_I2S_1_DMA_CONTROLLER_RX \
DT_ST_STM32_I2S_40013000_RX_DMAS_CONTROLLER
#define DT_I2S_1_DMA_CHANNEL_RX DT_ST_STM32_I2S_40013000_RX_DMAS_CHANNEL
#define DT_I2S_1_DMA_SLOT_RX DT_ST_STM32_I2S_40013000_RX_DMAS_SLOT
#define DT_I2S_1_DMA_CHANNEL_CONFIG_RX \
DT_ST_STM32_I2S_40013000_RX_DMAS_CHANNEL_CONFIG
#define DT_I2S_1_DMA_FEATURES_RX \
DT_ST_STM32_I2S_40013000_RX_DMAS_FEATURES
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2S_2_BASE_ADDRESS DT_ST_STM32_I2S_40003800_BASE_ADDRESS
#define DT_I2S_2_IRQ_PRI DT_ST_STM32_I2S_40003800_IRQ_0_PRIORITY
#define DT_I2S_2_NAME DT_ST_STM32_I2S_40003800_LABEL
#define DT_I2S_2_IRQ DT_ST_STM32_I2S_40003800_IRQ_0
#define DT_I2S_2_CLOCK_BITS DT_ST_STM32_I2S_40003800_CLOCK_BITS
#define DT_I2S_2_CLOCK_BUS DT_ST_STM32_I2S_40003800_CLOCK_BUS
drivers: i2s: change the stm32 DMA in the driver to use dts This commit moves DMA parameters previously hard coded in the driver to the dts. Signed-off-by: Song Qiang <songqiang1304521@gmail.com> Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-24 15:57:17 +08:00
#define DT_I2S_2_DMA_CONTROLLER_TX \
DT_ST_STM32_I2S_40003800_TX_DMAS_CONTROLLER
#define DT_I2S_2_DMA_CHANNEL_TX DT_ST_STM32_I2S_40003800_TX_DMAS_CHANNEL
#define DT_I2S_2_DMA_SLOT_TX DT_ST_STM32_I2S_40003800_TX_DMAS_SLOT
#define DT_I2S_2_DMA_CHANNEL_CONFIG_TX \
DT_ST_STM32_I2S_40003800_TX_DMAS_CHANNEL_CONFIG
#define DT_I2S_2_DMA_FEATURES_TX \
DT_ST_STM32_I2S_40003800_TX_DMAS_FEATURES
#define DT_I2S_2_DMA_CONTROLLER_RX \
DT_ST_STM32_I2S_40003800_RX_DMAS_CONTROLLER
#define DT_I2S_2_DMA_CHANNEL_RX DT_ST_STM32_I2S_40003800_RX_DMAS_CHANNEL
#define DT_I2S_2_DMA_SLOT_RX DT_ST_STM32_I2S_40003800_RX_DMAS_SLOT
#define DT_I2S_2_DMA_CHANNEL_CONFIG_RX \
DT_ST_STM32_I2S_40003800_RX_DMAS_CHANNEL_CONFIG
#define DT_I2S_2_DMA_FEATURES_RX \
DT_ST_STM32_I2S_40003800_RX_DMAS_FEATURES
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2S_3_BASE_ADDRESS DT_ST_STM32_I2S_40003C00_BASE_ADDRESS
#define DT_I2S_3_IRQ_PRI DT_ST_STM32_I2S_40003C00_IRQ_0_PRIORITY
#define DT_I2S_3_NAME DT_ST_STM32_I2S_40003C00_LABEL
#define DT_I2S_3_IRQ DT_ST_STM32_I2S_40003C00_IRQ_0
#define DT_I2S_3_CLOCK_BITS DT_ST_STM32_I2S_40003C00_CLOCK_BITS
#define DT_I2S_3_CLOCK_BUS DT_ST_STM32_I2S_40003C00_CLOCK_BUS
drivers: i2s: change the stm32 DMA in the driver to use dts This commit moves DMA parameters previously hard coded in the driver to the dts. Signed-off-by: Song Qiang <songqiang1304521@gmail.com> Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-24 15:57:17 +08:00
#define DT_I2S_3_DMA_CONTROLLER_TX \
DT_ST_STM32_I2S_40003C00_TX_DMAS_CONTROLLER
#define DT_I2S_3_DMA_CHANNEL_TX DT_ST_STM32_I2S_40003C00_TX_DMAS_CHANNEL
#define DT_I2S_3_DMA_SLOT_TX DT_ST_STM32_I2S_40003C00_TX_DMAS_SLOT
#define DT_I2S_3_DMA_CHANNEL_CONFIG_TX \
DT_ST_STM32_I2S_40003C00_TX_DMAS_CHANNEL_CONFIG
#define DT_I2S_3_DMA_FEATURES_TX \
DT_ST_STM32_I2S_40003C00_TX_DMAS_FEATURES
#define DT_I2S_3_DMA_CONTROLLER_RX \
DT_ST_STM32_I2S_40003C00_RX_DMAS_CONTROLLER
#define DT_I2S_3_DMA_CHANNEL_RX DT_ST_STM32_I2S_40003C00_RX_DMAS_CHANNEL
#define DT_I2S_3_DMA_SLOT_RX DT_ST_STM32_I2S_40003C00_RX_DMAS_SLOT
#define DT_I2S_3_DMA_CHANNEL_CONFIG_RX \
DT_ST_STM32_I2S_40003C00_RX_DMAS_CHANNEL_CONFIG
#define DT_I2S_3_DMA_FEATURES_RX \
DT_ST_STM32_I2S_40003C00_RX_DMAS_FEATURES
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2S_4_BASE_ADDRESS DT_ST_STM32_I2S_40013400_BASE_ADDRESS
#define DT_I2S_4_IRQ_PRI DT_ST_STM32_I2S_40013400_IRQ_0_PRIORITY
#define DT_I2S_4_NAME DT_ST_STM32_I2S_40013400_LABEL
#define DT_I2S_4_IRQ DT_ST_STM32_I2S_40013400_IRQ_0
#define DT_I2S_4_CLOCK_BITS DT_ST_STM32_I2S_40013400_CLOCK_BITS
#define DT_I2S_4_CLOCK_BUS DT_ST_STM32_I2S_40013400_CLOCK_BUS
drivers: i2s: change the stm32 DMA in the driver to use dts This commit moves DMA parameters previously hard coded in the driver to the dts. Signed-off-by: Song Qiang <songqiang1304521@gmail.com> Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-24 15:57:17 +08:00
#define DT_I2S_4_DMA_CONTROLLER_TX \
DT_ST_STM32_I2S_40013400_TX_DMAS_CONTROLLER
#define DT_I2S_4_DMA_CHANNEL_TX DT_ST_STM32_I2S_40013400_TX_DMAS_CHANNEL
#define DT_I2S_4_DMA_SLOT_TX DT_ST_STM32_I2S_40013400_TX_DMAS_SLOT
#define DT_I2S_4_DMA_CHANNEL_CONFIG_TX \
DT_ST_STM32_I2S_40013400_TX_DMAS_CHANNEL_CONFIG
#define DT_I2S_4_DMA_FEATURES_TX \
DT_ST_STM32_I2S_40013400_TX_DMAS_FEATURES
#define DT_I2S_4_DMA_CONTROLLER_RX \
DT_ST_STM32_I2S_40013400_RX_DMAS_CONTROLLER
#define DT_I2S_4_DMA_CHANNEL_RX DT_ST_STM32_I2S_40013400_RX_DMAS_CHANNEL
#define DT_I2S_4_DMA_SLOT_RX DT_ST_STM32_I2S_40013400_RX_DMAS_SLOT
#define DT_I2S_4_DMA_CHANNEL_CONFIG_RX \
DT_ST_STM32_I2S_40013400_RX_DMAS_CHANNEL_CONFIG
#define DT_I2S_4_DMA_FEATURES_RX \
DT_ST_STM32_I2S_40013400_RX_DMAS_FEATURES
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2S_5_BASE_ADDRESS DT_ST_STM32_I2S_40015000_BASE_ADDRESS
#define DT_I2S_5_IRQ_PRI DT_ST_STM32_I2S_40015000_IRQ_0_PRIORITY
#define DT_I2S_5_NAME DT_ST_STM32_I2S_40015000_LABEL
#define DT_I2S_5_IRQ DT_ST_STM32_I2S_40015000_IRQ_0
#define DT_I2S_5_CLOCK_BITS DT_ST_STM32_I2S_40015000_CLOCK_BITS
#define DT_I2S_5_CLOCK_BUS DT_ST_STM32_I2S_40015000_CLOCK_BUS
drivers: i2s: change the stm32 DMA in the driver to use dts This commit moves DMA parameters previously hard coded in the driver to the dts. Signed-off-by: Song Qiang <songqiang1304521@gmail.com> Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-24 15:57:17 +08:00
#define DT_I2S_5_DMA_CONTROLLER_TX \
DT_ST_STM32_I2S_40015000_TX_DMAS_CONTROLLER
#define DT_I2S_5_DMA_CHANNEL_TX DT_ST_STM32_I2S_40015000_TX_DMAS_CHANNEL
#define DT_I2S_5_DMA_SLOT_TX DT_ST_STM32_I2S_40015000_TX_DMAS_SLOT
#define DT_I2S_5_DMA_CHANNEL_CONFIG_TX \
DT_ST_STM32_I2S_40015000_TX_DMAS_CHANNEL_CONFIG
#define DT_I2S_5_DMA_FEATURES_TX \
DT_ST_STM32_I2S_40015000_TX_DMAS_FEATURES
#define DT_I2S_5_DMA_CONTROLLER_RX \
DT_ST_STM32_I2S_40015000_RX_DMAS_CONTROLLER
#define DT_I2S_5_DMA_CHANNEL_RX DT_ST_STM32_I2S_40015000_RX_DMAS_CHANNEL
#define DT_I2S_5_DMA_SLOT_RX DT_ST_STM32_I2S_40015000_RX_DMAS_SLOT
#define DT_I2S_5_DMA_CHANNEL_CONFIG_RX \
DT_ST_STM32_I2S_40015000_RX_DMAS_CHANNEL_CONFIG
#define DT_I2S_5_DMA_FEATURES_RX \
DT_ST_STM32_I2S_40015000_RX_DMAS_FEATURES
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
#define DT_I2S_6_BASE_ADDRESS DT_ST_STM32_I2S_40015400_BASE_ADDRESS
#define DT_I2S_6_IRQ_PRI DT_ST_STM32_I2S_40015400_IRQ_0_PRIORITY
#define DT_I2S_6_NAME DT_ST_STM32_I2S_40015400_LABEL
#define DT_I2S_6_IRQ DT_ST_STM32_I2S_40015400_IRQ_0
#define DT_I2S_6_CLOCK_BITS DT_ST_STM32_I2S_40015400_CLOCK_BITS
#define DT_I2S_6_CLOCK_BUS DT_ST_STM32_I2S_40015400_CLOCK_BUS
drivers: i2s: change the stm32 DMA in the driver to use dts This commit moves DMA parameters previously hard coded in the driver to the dts. Signed-off-by: Song Qiang <songqiang1304521@gmail.com> Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-10-24 15:57:17 +08:00
#define DT_I2S_6_DMA_CONTROLLER_TX \
DT_ST_STM32_I2S_40015400_TX_DMAS_CONTROLLER
#define DT_I2S_6_DMA_CHANNEL_TX DT_ST_STM32_I2S_40015400_TX_DMAS_CHANNEL
#define DT_I2S_6_DMA_SLOT_TX DT_ST_STM32_I2S_40015400_TX_DMAS_SLOT
#define DT_I2S_6_DMA_CHANNEL_CONFIG_TX \
DT_ST_STM32_I2S_40015400_TX_DMAS_CHANNEL_CONFIG
#define DT_I2S_6_DMA_FEATURES_TX \
DT_ST_STM32_I2S_40015400_TX_DMAS_FEATURES
#define DT_I2S_6_DMA_CONTROLLER_RX \
DT_ST_STM32_I2S_40015400_RX_DMAS_CONTROLLER
#define DT_I2S_6_DMA_CHANNEL_RX DT_ST_STM32_I2S_40015400_RX_DMAS_CHANNEL
#define DT_I2S_6_DMA_SLOT_RX DT_ST_STM32_I2S_40015400_RX_DMAS_SLOT
#define DT_I2S_6_DMA_CHANNEL_CONFIG_RX \
DT_ST_STM32_I2S_40015400_RX_DMAS_CHANNEL_CONFIG
#define DT_I2S_6_DMA_FEATURES_RX \
DT_ST_STM32_I2S_40015400_RX_DMAS_FEATURES
dts: arm: stm32: cleanup whitespace in dts_fixup headers Try to format the dts_fixup header files as uniformly as possible. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-09-19 16:35:52 +02:00
drivers: counter: rtc_stm32: convert to DT_INST defines Convert driver to use DT_INST_ defines. Removed DT_RTC_0 fixup macros but keep DT_RTC_NAME_0 as it is still in use across RTC users. Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2020-02-27 17:48:19 +01:00
#define DT_RTC_0_NAME DT_INST_0_ST_STM32_RTC_LABEL
drivers/rtc: Enable RTC driver for STM32F4 series Enable RTC driver for STM32F4 series. Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
2018-06-20 19:48:31 +03:00
soc: stm32: Add fixups for WWDG EWI and clock info Extended the WWDG fixups to support early wake interrupt handling and clock information. Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
2019-07-15 15:47:29 +03:00
#define DT_WDT_0_NAME DT_INST_0_ST_STM32_WATCHDOG_LABEL
soc: arm: stm32: Revert changes for ADC fixups We need to define DT_ADC_1_NAME to use generic ADC subsystems(ex. adc_shell). Signed-off-by: Takumi Ando <takumi@t15.red>
2020-03-18 21:31:36 +09:00
#define DT_ADC_1_NAME DT_ST_STM32_ADC_40012000_LABEL
arm: stm32f4: Add CAN1 support Add CAN1 pinmux definitions and DT entries for STM32F4 series. Signed-off-by: Erwin Rol <erwin@erwinrol.com>
2019-01-19 11:30:40 +01:00
#define DT_CAN_1_BASE_ADDRESS DT_ST_STM32_CAN_40006400_BASE_ADDRESS
#define DT_CAN_1_BUS_SPEED DT_ST_STM32_CAN_40006400_BUS_SPEED
#define DT_CAN_1_NAME DT_ST_STM32_CAN_40006400_LABEL
#define DT_CAN_1_IRQ_TX DT_ST_STM32_CAN_40006400_IRQ_TX
#define DT_CAN_1_IRQ_RX0 DT_ST_STM32_CAN_40006400_IRQ_RX0
#define DT_CAN_1_IRQ_RX1 DT_ST_STM32_CAN_40006400_IRQ_RX1
#define DT_CAN_1_IRQ_SCE DT_ST_STM32_CAN_40006400_IRQ_SCE
#define DT_CAN_1_IRQ_PRIORITY DT_ST_STM32_CAN_40006400_IRQ_0_PRIORITY
#define DT_CAN_1_SJW DT_ST_STM32_CAN_40006400_SJW
#define DT_CAN_1_PROP_SEG DT_ST_STM32_CAN_40006400_PROP_SEG
#define DT_CAN_1_PHASE_SEG1 DT_ST_STM32_CAN_40006400_PHASE_SEG1
#define DT_CAN_1_PHASE_SEG2 DT_ST_STM32_CAN_40006400_PHASE_SEG2
#define DT_CAN_1_CLOCK_BUS DT_ST_STM32_CAN_40006400_CLOCK_BUS
#define DT_CAN_1_CLOCK_BITS DT_ST_STM32_CAN_40006400_CLOCK_BITS
dts: arm: stm32f4: add CAN_2 controller Add the CAN controller device tree node for CAN_2 of the STM32F4 SoC series. Signed-off-by: Ivo Clarysse <ivo@bcdevices.com>
2020-01-25 06:59:38 -08:00
#define DT_CAN_2_BASE_ADDRESS DT_ST_STM32_CAN_40006800_BASE_ADDRESS
#define DT_CAN_2_BUS_SPEED DT_ST_STM32_CAN_40006800_BUS_SPEED
#define DT_CAN_2_NAME DT_ST_STM32_CAN_40006800_LABEL
#define DT_CAN_2_IRQ_TX DT_ST_STM32_CAN_40006800_IRQ_TX
#define DT_CAN_2_IRQ_RX0 DT_ST_STM32_CAN_40006800_IRQ_RX0
#define DT_CAN_2_IRQ_RX1 DT_ST_STM32_CAN_40006800_IRQ_RX1
#define DT_CAN_2_IRQ_SCE DT_ST_STM32_CAN_40006800_IRQ_SCE
#define DT_CAN_2_IRQ_PRIORITY DT_ST_STM32_CAN_40006800_IRQ_0_PRIORITY
#define DT_CAN_2_SJW DT_ST_STM32_CAN_40006800_SJW
#define DT_CAN_2_PROP_SEG DT_ST_STM32_CAN_40006800_PROP_SEG
#define DT_CAN_2_PHASE_SEG1 DT_ST_STM32_CAN_40006800_PHASE_SEG1
#define DT_CAN_2_PHASE_SEG2 DT_ST_STM32_CAN_40006800_PHASE_SEG2
#define DT_CAN_2_CLOCK_BUS DT_ST_STM32_CAN_40006800_CLOCK_BUS
#define DT_CAN_2_CLOCK_BITS DT_ST_STM32_CAN_40006800_CLOCK_BITS
drivers: flash: stm32: Convert to use device tree Convert STM32 flash drivers to use device tree to get the flash controller name and base address. Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2018-01-19 14:58:39 -06:00
/* End of SoC Level DTS fixup file */
Copy permalink