Private node identity advertisements must stop immediately when
ordered by PTS. To do so; adding enabled parameter to
btp_priv_node_id_get_cmd.
Signed-off-by: alperen sener <alperen.sener@nordicsemi.no>
Private Node Identity advertisement on a subnet should stop as soon as
the network is removed.
Signed-off-by: alperen sener <alperen.sener@nordicsemi.no>
The datasheet erroneously suggested to add a + 1 to the abort len.
This was suggested because if a controller gave a EoD, then it was
afraid that the abort would take precedence over the EoD. This was
not true. The EoD will always take precedence over a controller
abort. Remove the + 1 as this can cause issues.
For example, when talking to a part that will auto-increment a read
address, having the +1 can unknownly move this address pointer further
than anticipated.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
It is most certainly 'okay' for a secondary controller to do a
ENTDAA. Remove the 'block' that was preventing this.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Add a workaround for NRF52 anomaly 78: "High current consumption when
using timer STOP task only". Use the SHUTDOWN task instead.
For consistency, CLEAR the timer timer after STOPPING on devices that
lack the SHUTDOWN task. This also aligns the behavior with
nrfx_timer_disable().
For devices with the SHUTDOWN task, this restores the behavior previous
to e92323f.
Fixes#87224
Signed-off-by: Marco Widmer <marco.widmer@bytesatwork.ch>
Fixes an issue where pinctrl psel properties encoded with
NRF_PSEL_DISCONNECTED() caused a build failure.
Signed-off-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
Add missing support for J-Link in board.cmake configuration
for Nucleo G4 boards so they can be
flashed and debugged using J-Link.
Signed-off-by: Kuba Gryglak <gryglak.kuba@protonmail.com>
doc: same54_xpro Fixed broken links in index
- Updated pdf link to datasheet
- Added html link to datasheet
- Added link to product page
- Updated zip file link
- Added zip file link to newer revision
Signed-off-by: Robert Perkel <robert.perkel@microchip.com>
The disparity in C objects built causes
the test to fail.
This removes those lines from the log
to inline log comparison.
Let's disable it in the relevant test.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
Replace uses of OVERLAY_CONFIG with EXTRA_CONF_FILE
to follow the rest of Zephyr where OVERLAY_CONFIG was
deprecated in favor of EXTRA_CONF_FILE.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
`nsos_connect_blocking()` is not returning the error as expected. It is
expected to return a negative `NSI_ERRNO_MID_...` value, but it is
returning a positive errno value. `nsos_connect_blocking()` should map
the errno value to a negative `NSI_ERRNO_MID_...`, which `nsos_connect()`
maps back to a -1 return with errno=`ECONNREFUSED`.
the current sequence of events:
- `ECONNREFUSED` occurs during connection
- `nsos_connect_blocking()` returns positive `ECONNREFUSED`
- `nsos_connect()` returns positive `ECONNREFUSED`
- `zsock_connect()` returns positive `ECONNREFUSED`
the expected sequence of events:
- `ECONNREFUSED` occurs during connection
- `nsos_connect_blocking()` returns negative `NSI_ERRNO_MID_ECONNREFUSED`
- `nsos_connect()` returns -1, errno=`ECONNREFUSED`
- `zsock_connect()` returns -1, errno=`ECONNREFUSED`
Signed-off-by: Noah Olson <noah@wavelynx.com>
Having the log level set at debug causes a message to be printed
every time a mailbox message is sent or received. If we log this
using the RPMSG shell, then each message sent generates another
message, causing an an infinite message loop.
Do not set the level to debug by default, allow the level to
be set by the config LOG_DEFAULT_LEVEL.
Signed-off-by: Andrew Davis <afd@ti.com>
If an option is set in the project default configuration it does not
need to be set again in a board specific configuration overlay. Remove
instances of this.
Signed-off-by: Andrew Davis <afd@ti.com>
The message data field is currently empty, this works for some as the all
available virtqueues can be signaled when any message comes in on the host
side. For TI Mailbox and RemoteProc Linux drivers we do check the content
and expect the message to contain the correct Vring ID to signal.
Signed-off-by: Andrew Davis <afd@ti.com>
When core is suspended and power mode has non zero exit_latency_us
a system timeout will be rescheduled to a point in time that is
earlier by exit_latency_us than request. It is to accommodate for
lengthy resuming procedure which would cause requested timeout to
be significantly late. However, setting additional wake up point
has cost, it is one more redundant core wake up and that impacts
performance and power consumption.
Add Kconfig option to chose what conversion method is used. It has
the biggest impact on small exit_latency_us where conversion may
result in 0 ticks (no pre-wake up) or 1 tick (wake up).
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
This removes big structures allocated on stack.
It also moves linked list node to dedicated buffer.
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
Remove InitStructs of LL driver, since they take a lot of space on stack.
This can cause stack overflow in some scenarios.
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
Keep the minimum configurations in frdm_rw612.conf and rd_rw612_bga.conf
for basic STA functionality of embedded supplicant case.
Add the superset configurations in nxp/overlay_rw612.conf.
Add the supplicant support in nxp/overlay_hostap_rw612.conf.
Add the basic debug support in nxp/overlay_rw612_debug.conf.
Add the supplicant debug support in nxp/overlay_hostap_rw612_debug.conf.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
NET_L2_ETHERNET should be enabled by default.
NXP_WIFI_SHELL should be enabled by default when SHELL is enabled.
NXP_WIFI_TX_RX_ZERO_COPY should not be enabled by default for RW612,
as it has special requirement for NET_BUF_DATA_SIZE.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
MCUboot has a configuration for single application slot RAM loading, in
which the single loader (or a hook thereof) can load an application from
an arbitrary flash location to RAM. Applications that are to be loaded
in this way need to specify, in their mcuboot header, the load address
in RAM they are meant to be loaded.
This patch adds a new Kconfig for this mode. The load address used comes
from devicetree chosen property "mcuboot,ram-load-dev", if it exists,
and if not, "zephyr,sram".
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Some OpenThread functions were called without verifying the return
value, which not only is not the best practice, but also could lead to
build warnings with llvm. This commit fixes it.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The IT8xxx2 timer driver uses timer 7 and timer 8 to implement the alarm
timer and the top timer, respectively.
Signed-off-by: Yunshao Chiang <Yunshao.Chiang@ite.com.tw>
Add possibility to use pinctrl to configure pins that should be assigned
to nRF VPR coprocessors and also provide a way of preventing activation
of the nordic_vpr_launcher driver for an enabled VPR so that it can be
supplied with the code to execute and launched in a custom way.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add an entry for the RAM region assigned to soft peripherals that will
disable caching for that region. Without this, communication with the
FLPR coprocessor cannot be performed correctly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
