- Optimize slot sizes for MCUBoot swap move algorithm
for mimxrt1160/70 boards.
- Use DT_SIZE_K/M macros for slot sizes.
- Limit mcuboot max size to 128KB.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
As far as I can tell it appears that the hardware
does not support acceleration of ICMPV6 checksums.
For now, the easiest way to fix the runtime failure of
IPV6 is just to disable the hardware acceleration if
IPV6 is expected to be used.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Handling of board changes was broken and did not support v2 boards, fix
this to optimize CI execution on localized changes of board files.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The test is broken in CI because the emulated spi bus is not built in,
adding an explicit CONFIG_EMUL=y to the test config.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add devicetree nodes for the Reset Information registers on nRF54H20,
along with a new binding.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Remove dead code that cannot be enabled.
Kconfig prevents us from enabling PM_S2RAM on 53 because it is not
supported any more.
But we still have some dead code left over in soc.c, so we delete this
code.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The doc comment relating to mpsc atomics was worded poorly. Remove
the poorly worded doc comment related to atomics and caches.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Moves the rtio_ prefixed lockfree queues to sys alongside existing
mpsc/spsc pbuf, ringbuf, and similar queue-like data structures.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Previously, dtlib would fail to parse the following:
/delete-node/ &{/};
This is accepted by dtc, so dtlib should be aligned.
The expected behavior is that the contents of the "deleted" root node
are emptied, but the node itself remains in the tree. This means that
it's possible to put that statement at the end of a DTS file and still
get a valid output. A small test case for this scenario is included.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add the test cases for Sensing(Sensing Subsystem) to verify the
functionality of sensing portion of subsystem.
The test cases are based on native_sim platform.
Signed-off-by: Qianru Huang <qianru.huang@intel.com>
Introduce the stm32h7s78_dk disco kit from STMicroelectronics
Based on the stm32H7S7 mcu
Use STM32CubeProgrammer v2.16.0 as runner.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce the stm32h7RS serie to the gpio driver,
based on the stm32h7
The SBS controller is used to configure the EXTI line among
the different GPIO port.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce the stm32h7RS serie to the pin control driver,
New GPIO port M, N, O, P
Then add the complete list and from A to P (16 port
coded on 5 bits)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce the stm32h7RS serie to the clock_controller,
based on the stm32h7 clock driver
Datasheet DS14359 rev 1 gives CPU max freq of 500MHz
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the new stm32h7rs serie with stm32H7R3, stm32H7R7,
stm32H7S3, stm32H7S7 devices from STMicroelectronics
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the support of the STM32H7RSX to the
include/zephyr/dt-bindings/reset/stm32h7_reset.h
which differs from the stm32h7 with an APB5 bus
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce the stm32h7RS serie to the clock rcc controller,
and the exti interrupt controller based on the stm32h7 rcc bindings.
Three PLL clocks are available.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the new STM32HRSX serie with stm32H7R3, stm32H7R7,
stm32H7S3, stm32H7S7 devices from STMicroelectronics
Same MPU regions as stm32h7 device.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the property of drive-strength to drive a high or low current
selection. If this property is not configured, it is the default
setting. According to the SPEC, the default drive current selection
varies from different pins.
Define the high level 0b: 8mA
low level 1b: 4mA or 2mA
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add support for configuration of the ARM PLL on the iMXRT1170/1160
series SOCs. This PLL is used to generate the M7 core frequency, and is
an integer pll. Provide default configurations for the RT1160 and RT1170
targeting 600MHz and 1GHz respectively.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
RW612 board overlay should remove the MIPI DBI nodes defined at the
board and at the shield level, because the LCDIC peripheral on this SOC
can support the MIPI DBI protocol directly without the emulated Zephyr
driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Previously the schedule_next_timeout() function was feeding the hardware
watchdog irrespective of whether or not it was started. This is now
fixed.
Signed-off-by: Balaji Srinivasan <balaji.srinivasan@nordicsemi.no>
Calculate and set a proper Transceiver Delay Compensation Offset (TDCO)
based on FlexCAN FD timing.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add testcases for rk043fn02h_ct and rk043fn66hs_ctg shields to display
and LVGL samples, so these testcases will be built by CI.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove display definition for the RT1060 EVK. This display panel is now
supported as the RK043FN02H-CT shield. Add this information to the
documentation for the board, along with other tested shields.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a shield for the RK043FN66HS-CTG panel, a Rocktech display panel with
an GT911 touch controller. This panel uses a 40+6 FPC interface for
parallel displays, which is supported by many NXP iMX RT EVKs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a shield for the RK043FN02H-CT panel, a Rocktech display panel with
an FT5336 touch controller. This panel uses a 40+6 FPC interface for
parallel displays, which is supported by many NXP iMX RT EVKs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Define parallel and i2c FPC display interfaces for the RT1060 EVK. These
interfaces are used by multiple displays for the EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add bindings for nxp display interfaces. These bindings describe the 6
and 40 pin FPC connectors used for displays on several NXP EVKs using
gpio nexus nodes.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rename the POSIX_RWLOCK_INITIALIZER back to PTHREAD_RWLOCK_INITIALIZER.
This was changed in 70e2b02c8e, but PTHREAD_RWLOCK_INITIALIZER is the
standard name used by external libraries.
Change it back to restore compatibility.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Looking to expand the sensor docs and break out significant sections.
First though to move this to a directory to allow for multiple sensor
related rst docs.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
