This allows to build the shell with BT_CTLR_DTM and/or BT_CTLR_ADV_EXT
enabled.
The issues has been introduced by commit
bf897cf941 (Bluetooth: Shell: Restructure
shell files).
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Before this patch, any unexpected socket error during poll (caused by
LTE disconnects for instance) would lead to a infinite loop because the
error state was never cleared, handled or even signaled to the user.
Signed-off-by: Benjamin Lindqvist <benjamin@eub.se>
This is a bug fix for adxl372_accel_convert_q31 function.
Function is used to convert samples received from
sensor to q31_t format when RTIO stream is used.
Signed-off-by: Vladislav Pejic <vladislav.pejic@orioninc.com>
Optimize function which enables UARTE peripheral. It is called
only when interrupts are locked so data->flags does not require
atomic operation. Use standard logical operations so save few
bytes.
Simplify uarte_disable_locked.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
So far new platforms did not use legacy shim but it shall
be now a default uart shim for all platforms.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Improved a workaround. When FIFO is not empty then FLUSHRX
task will generate RXSTARTED event to indicated that DMA transfer
was started. This property can be used to detect when FIFO was
not empty and workaroud a HW bug where RX.AMOUNT register is not
updated after flushing empty FIFO.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add runtime PM to the driver. When asynchronous or interrupt
driven API is used, there are 3 independent paths for enabling
the device: RX, TX and TX poll_out. TX poll_out requires special
handling because number of poll_out calls does not need to much
number of TXSTOPPED interrupts. To handle that special flag is
added. For standard RX and TX is simpler.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
A code ifdefed by UARTE_BAUDRATE_RETENTION_WORKAROUND was missing a
closing bracket. It was missed because CI did not compile any target
that is applying this workaround and enables code compilation.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Remove the use of floating point to calculate in
`pwm_rpi_get_cycles_per_sec` to fixed point calculations that result in the
same value. There is still a division here, which is somewhat slow still,
but the end result about twice fast for the whole path through the led pwm
code.
Even better would be to cache these values, since there is no interface in
this driver to change the configuration past init time.
Signed-off-by: David Brown <david.brown@linaro.org>
Zephyr 3.7.0 has been released and it is time to remove the migration
code added in 9cf07bbdb5 (bluetooth:
Rename rpmsg HCI driver and sample to ipc).
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
The cache_size and lookahead_size are set at compile time using the
CONFIG_FS_LITTLEFS_CACHE_SIZE and CONFIG_FS_LITTLEFS_LOOKAHEAD_SIZE values
from Kconfig, or from the cache-size and lookahead-size properties in a
'zephyr,fstab,littlefs' compatible in the devicetree. Those values are
also used to statically allocate buffers that are pointed at by the
read_buffer, prog_buffer, and lookahead_buffer members of the lfs_config
structure.
At runtime, when using a block device, the cache_size and lookahead_size
are updated to be multiples of the underlying block device's block_size,
which may make them bigger than the original size used to allocate the
static buffers. Log an error and fail the operation when this occurs.
Signed-off-by: Phil Hindman <phindman@xes-inc.com>
Added check where stream_flash_erase_page checks if requested
offset is actually within stream flash designated area.
Fixes#79800
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The current selected start-up time takes 8 seconds to initialize.
When xosc32 is used as main clock reference it blocks the whole
initializarion of the system by that amount of time. This patch
relax that condition setting the initialization time to 62ms.
Fixes#79949
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Both ram and rom reports print their outputs in the console
and publish their reports in json.
footprint is wrapper to generate both reports but it is currently
not printing their outputs in the console nor given any feedback to
the user that those reports were generated.
Change it to behave like the others reports allowing the user to see them
and / or redirect to a file if they want.
Signed-off-by: Flavio Ceolin <flavio.ceolin@gmail.com>
Removed the LE Audio specific definition and instead
refer to the value defined by iso.h as it is ISO/Core
that defines this size, and not BAP/Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
With the recent introduction of the SUIT manifest starter binary blob,
it is now possible to use it with the nRF54H20 during the flashing
procedure in order to provide a valid SUIT manifest to the system.
This PR introduces the code that handles programming the SUIT manifest
starter, as well as a new --suit-manifest-starter command-line option.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The format specifier for size_t is zu.
Using d only works when int and size_t are the same
underlying type which is not the case for 64bit systems,
which leads to a build warning in this case.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
There are issues with 64 bit compilation in hostap so disable
native_sim/native/64 board from the tests. The board will be
enabled again after updating the hostap from upstream and fixing
the issues.
Fixes#80437
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The bis_iso_qos.rx was missing in param sent in bt_iso_big_sync
Also, MSE = 0 is valid (fixed error check)
Signed-off-by: Lars Knudsen <LAKD@demant.com>
Add optional value parameter to dt_compat_any_has_prop
kconfig preprocessor function, which puts an additional constraint on
the truth of the function in that the property value must match the
parameter value.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
By defining this snippet it becomes simpler to build an application
for the Zephyr Bluetooth Controller in environments
where this is not enabled in device tree by default.
It removes the need for adding boilerplate overlay files
to applications.
Also, we would be able to add this snippet by default for
samples and tests where it is required to use the zephyr
link layer.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Reset value of this register is supposed to be 0 but I noticed on some
chip, it was not resetting to 0 on system reset, don't know why, but
this supposedly redundant clear is fine for now.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
These properties should eventually be removed from this binding as they
have been introduced to control soc specific clock trees and don't
correlate to anything in the IP, but for now just make them not required
and remove them from DT for SOCs that don't even use them.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
WS25Q512JV can only run at 104MHz at 3.3V, unless the read parameter
bits are changed. Since we don't reprogram these currently, reduce max
frequency to safe value
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This is a bug fix for adxl362_temp_convert_q31 and
adxl362_accel_convert_q31 functions.
Functions are used to convert samples received from
sensor to q31_t format when RTIO stream is used.
Signed-off-by: Vladislav Pejic <vladislav.pejic@orioninc.com>
For tests that support both targeting unit_testing and
other targets, we check in the cmake code the BOARD variable.
Let's allow users to set this to either of unit_testing
or unit_testing/unit_testing so it behaves like for other
tests.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Fix filtering done in
22c3438f1b
Otherwise we end up with tests defined twice, as a .unit and .zerphyr
variant but both run in normal builds, and none for unit tests.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Use full board name in cmake file.
Akin to the fix done in
https://github.com/zephyrproject-rtos/zephyr/pull/80270/
following the changes from
https://github.com/zephyrproject-rtos/zephyr/pull/77250/
Note after the Zephyr cmake code has been run the BOARD
variable is split into BOARD BOARD_QUALIFIERS,
where BOARD does not contain the qualifiers anymore
(see cmake/modules/boards.cmake for more info).
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The truncation is not possible in practice but add suitable cast to
avoid the warning.
samples/net/sockets/echo_server/src/tcp.c:297:54: warning:
‘%d’ directive output may be truncated writing between 1 and 10 bytes
into a region of size 5 [-Wformat-truncation=]
297 | snprintk(name, sizeof(name), "tcp4[%d]", slot);
| ^~~~~~~~~~
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The NET_SOCKET_SERVICE_SYNC_DEFINE_STATIC() macro was changed
earlier but the compilation error was missed. Fixing the macro
call.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
