The CSI needs to be initialized BEFORE the camera sensor to provide
clock to the camera sensor. It is now possible to do so as direct
reference to the sensor via phandle is now removed. There will be
no check failure on the init order anymore when compiling.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "source_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Remove the obsolete comment about the init order of the CSI and the
camera sensors (e.g. mt9m114) which is not true anymore.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
As getting bytes per pixel of a pixel format is a very common operation,
add an utility function for it instead of repeating the same codes in
different drivers.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Instead of fixing csi2rx clock frequencies, set them according to the
pixel rate got from the camera sensor.
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Add set_ctrl callback to propagate controls to the sensor.
Signed-off-by: Farah Fliss <farah.fliss@nxp.com>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "sensor_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The ov5640 camera driver now supports both MIPI CSI2 (DPHY) and DVP
modes. It is in MIPI CSI2 mode in this overlay. Add bus-type property
for this. In this mode, data-lanes property is required as well.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Change the bytes occupied by the ssid member in the wifi structure
to 'WIFI_SSID_MAX_LEN + 1' so that it can eliminate the
'-Wstringop-truncation' warning.
Signed-off-by: James Roy <rruuaanng@outlook.com>
nrf54h20dk_nrf54h20_cpurad by default has less RAM dedicated for
DMA transfers and default 1k buffer cannot be used for
uart_async_long_buf case. Use custom value.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
One of the test case is performing long transfers using 1k buffers.
For some targets there may be not enough RAM to perform such
transfers. Make long buffer length configurable.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The LPC55S36 board has an integrated MCU-Link debug probe, not an
LPC-Link2. Also, it is now possible to directly use the stock CMSIS-DAP
mode with the `linkserver` runner.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
HAS_SEGGER_RTT Kconfix symbol is missing in NXP MCXC series Kconfig.
Add the symbol to fix and enable Segger RTT samples.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Add the Kconfig menu to the sample configuration.
Update sample.yaml by adding the shield configuration.
Signed-off-by: Charles Dias <charlesdias.cd@outlook.com>
mcxc242 has usb device capability. Add usb to board documentation and
to the yaml file. Enable and configure it in board dts.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
USB configuration is missing in Devicetree for NXP MCX C series.
Add the configuration to common and SoC specific dtsi file.
Delete usb node for SoCs without USB support.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Some NXP socs with Kinetis USB do not have USB voltage regulator.
It causes build error in USB samples.
Fix it by enabling and disabling the voltage regulator only if
present.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Some NXP SoC's do not have USB voltage regulator present.
Add property to indicate it. Negative logic is used, because
the regulator is present in great majority of SoC's, and thus the new
property can be added only for SoC's without the regulator.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Similar to commit aeec014cbe, this
renames the identifiers to have prefix of "__llext_sym_name_"
instead of having suffix of "_sym_name" in LLEXT symbol tables
for SLID-enabled applications. This is needed to avoid confusing
the gen_device_deps.py script as it searches for objects (e.g.
__device_dts_ord_*) by matching name stems without regard to
suffixes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Replace "CONFIG_SOC_SERIES_STM32H7X || CONFIG_SOC_SERIES_STM32H5X"
by the compatble st_stm32h7_ethernet
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
Add stm32h7 ethernet compatible "st,stm32h7-ethernet",
used also for stm32h5.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
