This puts the QSPI peripheral into memory-mapped mode when
CONFIG_STM32_MEMMAP is set. Writes and erase put it back into indirect
write mode.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
This CONFIG_STM32_MEMMAP is for enabling the MemoryMapped mode
on external octo or quad spi memory.
In this case, the flash_stm32_read is done in mem map mode
the flash_stm32_erase is not available.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
When CONFIG_USB_DEVICE_STACK=n then the sine wave
generator was enabled, which caused build errors.
This commit fixes those errors and also adds the
nRF5340 as a build target for the USB tests.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Align SYS_CLOCK_HW_CYCLES_PER_SEC with other SMP nSIM
configurations and set it to 1000000.
This significantly reduce verification time on HS5x platforms.
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Access to this region should no longer be requested via UICR, because it
will be statically reserved by secure domain firmware.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
PR #72100 broke execution of unit type tests. This commit fixes
it by bringing back the "old" logic for selecting a binary path
for unit type tests.
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
Check if the driver is suspended in gpio_keys_change_deferred(), this
avoids a potential situation where a race condition could try and read
from a pin that has just been disconnected.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Since a long is 64-bits on 64-bit architectures, and 32-bits
on 32-bit architectures, we can simplify the definition of
PRIQ_BITMAP_SIZE by defining it in terms of BITS_PER_LONG.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
The gpio-emul driver does not actually require any reg property,
since it is not in the physical memory map of any device. So
let's remove that property from the bindings.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
When a sensor that depends on an ADC is enabled in devicetree, enable
the ADC subsystem. ADC is roughly equivalent to a bus for these sensors
(the mechanism through which data is transferred), which had the same
conversion applied in #48707.
The same benefits apply here, namely removing the need for the following
pattern in board `.kconfig` files:
```
configdefault ADC
default y if SENSOR
```
Signed-off-by: Jordan Yates <jordan@embeint.com>
Some stm32 devices with quadspi (like stm32l47x or stm32l48x)
does not support Dual-Flash Mode. Avoid building error even if
the &quadspi node has a <flash-id> property defined.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The mic_state is a guarded field in event_done_extra where it was
accessed outside of its guard.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Remove all CAN controller "bus-speed" and "bus-speed-data"
properties. These all use the default bitrates set via Kconfig.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Set the default initial bitrates globally via Kconfig. The initial bitrates
can still be overridden using the "bus-speed" and "bus-speed-data"
devicetree properties.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fix missing change to run Twister with default options setup.
Should be implemented together with #72399
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
SD ops card_read() implementation does not need to unlock mutex, as this
is managed by the calling function card_write_blocks. Remove this stray
k_mutex_unlock() call.
Fixes#72287
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
RCAR MMC driver previously had to report inaccurate maximum supported
frequency to SD subsystem so that the subsystem would select SDR104 mode
timing. Remove this logic, as it should no longer be needed.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Report bus frequency, and use correct names for the timing modes when SD
cards do not support UHS modes.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Reword frequency and timing selection logic for SDIO framework so that
the maximum supported timing mode between the card and host will be
selected, even if the maximum frequency supported by the host is not
equal to the maximum frequency for that mode.
Also, resolve an issue where a host and card combo only supporting HS
mode or worse would still use legacy timing mode, because the CCCR flags
were not being checked when checking if HS bus speed could be used.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
SDMMC framework frequency and timing selection logic has several
longstanding issues, including:
- requiring that SD hosts support the maximum frequency possible for a
given UHS mode in order to apply that timing
- selecting SDHC_TIMING_SDR25 for high speed mode, when SDHC_TIMING_HS
would be correct
Rework the frequency and timing selection logic within the SD framework
to resolve these issues.
Fixes#52589Fixes#67943
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add UNSUPPORTED frequency macro for HS mode frequencies, used when a
card does not support any high speed mode frequencies
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use frequency macros to define SD frequencies, this should increase
readability of the file and reduce errors.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rather than relying to the alphanumeric test ordering implemented in
ZTEST to ensure certain tests run first, setup the SDHC IO properties to
known good values before starting any of the tests. This allows the SDHC
tests to run in any order, rather than needing certain tests to run
first.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update NXP hal to the revision pointing to the following commit:
"drivers: csi: Rework to fix the low framerate issue"
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The default stack size of RFCOMM DLC is 256.
The default value is sufficient for basic operation.
If more stack space is used (such as call function printk)
in context of callback disconnected of RFCOMM DLC, the
default stack size is not sufficient.
Add a configuration BT_RFCOMM_DLC_STACK_SIZE to configure
the RFCOMM DLC stack size.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
To avoid the case that CONN_TX is available but RFCOMM_TX is
unavailable, set the default value of BT_RFCOMM_TX_MAX to
BT_CONN_TX_MAX.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
The maximum data length of event packet is 255 for BR/EDR.
Such as the data length of event Remote Name Request
Complete is 255.
Set BT_BUF_EVT_RX_SIZE to 255 to avoid error "Not enough
space in buffer" from bt_hci driver.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Add macros to get Major Service Classes, Major Device
Class and Minor Device Class.
Define Major Device Class code.
Define Minor Device Class field for Computer Major
Class.
Define Minor Device Class field for Phone Major Class.
Define Minor Device Class field for Audio/Video Major
Class.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Fix default command line options check dependency on `--device-testing`
when it is provided to run Twister and turn device command options
as mandatory.
Fixes after changes introduced with #72399.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
If the controller can detect VBUS state changes, enable USB support only
when the device is connected and disable it when the device is
disconnected.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Lock the scheduler to ensure that the context is not preempted before it
is fully initialized.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
udc_init() only initializes and enables the USB regulator. This is
enough to detect VBUS changes, the USB controller is enabled in
udc_enable(). Deinitialization happens correspondingly in reverse order.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
There are controllers with capability to detect VBUS state change. This
can be used in a generic application to explicitly handle the VBUS
detected event after usbd_init() and for example allow the PMIC to
detect to what type of port device controller is connected.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
