This adds HCI driver which enables communication with CMAC core on
Renesas SmartBond DA1469x series. The CMAC core is running an Apache
NimBLE controller binary and uses shared memory for communcation via
mailboxes.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Enable PWM and PWM_CAPTURE in conf and add pwm node to app.overlay.
Add TSic xx6 node to pwm.dtsi.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add driver for TSic 206/306/316/506F/516/716 temperature sensor.
The driver uses PWM capture driver to read a single wire with
Manchester-like encoding.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Update Zephyr fork of MCUboot to revision:
018dc01d484358d81f889c36471d9ce5590965b6
Brings following Zephyr relevant fixes:
- 018dc01d boot/zephyr: use socs conf
- d4394c2f mbedtls config: fix too early check_config.h
includes
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Implement more robust handling for legacy SFDP tables, which may not
implement some of the JEDEC defined DWORDS for SFDP data. Instead of
failing to probe/initialize the flash when these DWORDS are not defined
in the basic flash parameter table, revert to sane defaults for SPI
flash.
Fixes#72051
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Let's also explicitly test that absolute timeouts trigger
at the correct time, even if the kernel has not seen
system clock timer announcements for a while.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
`CONFIG_PM_DEVICE` being disabled does not mean that the `power-gpio`
does not need to be controlled.
Additionally, not having a `power-gpio` property does not mean that
power management is not supported, just that is has no work to do.
Signed-off-by: Jordan Yates <jordan@embeint.com>
In #72651, build fails due to conflict when enabling mbedTLS components.
Current Wi-Fi implementation for ESP32 can discard those selected cryptos.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Take card lock when running IOCTL command, to avoid race conditions that
could occur within the lower SDHC transfer implementations (as these
will be called by sdmmc_wait_ready)
Fixes#72368
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The ARC QEMU boards are maintained by Synopsys, so
let's add boards/qemu/arc to Synopsys platform entry
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Fix the compile error when input driver is enabled.
Error message:
In file included from zephyr/zephyr/include/zephyr/sys/util_macro.h:34,
from zephyr/zephyr/include/zephyr/irq_multilevel.h:15,
from zephyr/zephyr/include/zephyr/devicetree.h:20,
from zephyr/zephyr/include/zephyr/device.h:12,
from zephyr/zephyr/drivers/input/input_gpio_keys.c:9:
zephyr/zephyr/include/zephyr/toolchain/gcc.h:87:36:
error: static assertion failed:
"zephyr-code must be specified to use the input-gpio-keys driver"
Signed-off-by: Jason Yu <zejiang.yu@nxp.com>
Apply the commit 21975231e2
("usb: device: cdc_acm: Prevent recursive logging loop")
to the new CDC ACM implementation.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The CDNS will report a M0 error if the data length is not what
it expects, but certain CCCs can have a variable length such as
GETMXDS and GETCAPS. This sets it up to ignore the M0 error if
it sees that ccc was GETMXDS or GETCAPS.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
GETSTATUS and GETMRL where not checking the right argc length. This
corrects it to check for the right count.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
adds API checks for fixed partitions access macros that are
called with nodes as an argumet.
Signed-off-by: Mateusz Michalek <mateusz.michalek@nordicsemi.no>
adds size, offset and divice access macros that are
operating with nodes as an argumet.
Signed-off-by: Mateusz Michalek <mateusz.michalek@nordicsemi.no>
Let's use the native_posix entropy driver by now,
as the real target relies on the PSA one, and we
currently do not have plans to include that.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This is not yet possible.
So let's add a check that provides an easy to understanding
error message instead of a bunch of kconfig and build warnings.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
These tests run fine in this board, let's provide an
overlay and enable them.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Misc fixes for the grtc timer driver:
* In non tickless mode:
* The tick time would drift a bit with each interrupt
* If something would cause a very significant delay
in handling the tick interrupt the number of announcements
would be incorrect
* Fortickless mode: The calculation of the next tick time
in sys_clock_set_timeout() was incorrectly done,
resulting in two spurious, too early, wakes of the kernel
before each correct wake. This caused tests/kernel/context/
to fail.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
* Update the HW models module to
5d638052c9fe1ef3bd7638067354eba4d3f2fa78
Including the following:
* 5d63805 Makefile: Also build NRF54L15 models by default
* 0154337 GRTC: Add model
* ecd2a01 PPIB: Add model
* 086fe1e hal: hack: Add initial nRF54L15 support
* 384f29d zephyr integration: Add support for nRF54L15
* b17fffc hal: Include new peripherals hals in static hal version
* 67fc961 TEMP: Add nrf54L15 reset values
* 4fd6b6f docs: HW impl. status: Add nrf54L15
* 30f7a7b nrf54L15: Initial HW models with reused peripherals
* 6150de0 TIMER: Add support for CLK freqs != 16MHz
* 4b245cd IRQ controller: Fix typo
* 0b0ab3a irq_ctrl: Support more than 64 interrupts
* 86800c9 Override HAL type qualifiers to remove const
* d2433a1 Make: Add basic infra for NRF54L15
* 3ec8f66 nrf_hack: Reorganize header in preparation for the nrf54 plat
* 9f1f473 DPPI types: Use 54 like NRF_DPPI names
* ed8f9b7 Make: Provide a reasonable default for BSIM_COMPONENTS_PATH
* e55aaff RADIO: Add an explicit check to silence a build warning
* 7630b69 RADIO: Make function declaration prototype
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The new kconfig options intend to represent a final
nRF54L product, let's handle them appropriately.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
In preparation for simulated nRF54L targets,
let's add kconfig options aking to the ones
we have for the nRF52 and 53 devices.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Move it to a common file named `zephyr,memory-common.yaml`, which
replaces `zephyr,memory-attr.yaml` and takes its contents as well.
This is so that another binding, e.g., `vnd,memory-region`, can support
being combined with the `zephyr,memory-region` binding like so:
node@deadbeef {
compatible = "vnd,memory-region", "zephyr,memory-region";
zephyr,memory-region = "NAME";
...
};
To allow this, edtlib would require `vnd,memory-region` to include the
property definitions from this new common file.
The same can't be done by including `zephyr,memory-region.yaml` directly
because that file marks the property in question as always required, and
it shouldn't be required whenever the `vnd,memory-region` compatible is
used on its own.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add the Kconfig options and use the aliased
addresses for the bootcode regions of the IMX7D
and IMX6SX SOCs to allow the Linux rproc
framework to load the irq-vectors into
the correct memory areas.
Activating this option might enlarge the bin
file if the zephyr,flash and rom_start chosen
region addresses are not matching.
It is up to the user to enable this feature
based on code location choices (OCRAM, DDR, TCM...).
Signed-off-by: Jérémy LOCHE - MAKEEN Energy <jlh@makeenenergy.com>
In order to support Linux rproc loading, some SOCs require
the boot-vector and irq-vectors to be placed into a defined
memory area for the mcu to boot.
This is necessary for NXP's IMX SOCs for instance but
can be leveraged by other SOCs that have multiple
zephyr,flash choices.
Signed-off-by: Jérémy LOCHE - MAKEEN Energy <jlh@makeenenergy.com>
By default, the QSPI region is marked as EXTMEM and inaccessible
(see #57467), mark the first 64MB as IO on stm32f769i_disco.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
According to the datasheet, fRSCLK (Clock Frequency for READ instructions)
is 66MHz; it doesn't mention 72MHz anywhere.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
