Change updates log level only if UART log backend is enabled in Kconfig
configuration. The log level update is not needed in case logs are
provided over other backend (e.g. RTT).
Change affects both USB stacks.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Uart FIFO is useful in case of wakeup on serial as it will allow
to avoid losing chars.
Enable it systematically on all overlays for this sample.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Add tests suite covering HTTP2 HPACK header compression and Huffman
encoding.
Note - many HPACK encoding/decoding cases in tests look similar, but
there are subtle differences in HPACK header used. For decoding, we
should be able to decode all of them. For encoding, we only test what
we support (no dynamic indexing).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Current NET_SOCKETS_POLL_MAX and ZVFS_OPEN_MAX values were too low for
the sample after the DNS refactoring, making the sample unusable in
current state.
Bump those values accordingly to make the sample functional again.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
We should return the errno value in such case, as ret will always be -1
on failure, which might misleading, as it does not give any hint on what
failed.
Also bump the log level of the error message, so the failure is visible
w/o needing to enable debug logs. Such a failure is fatal for the DNS
subsystem, so error level is justified here.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The `dns_data` buffer, allocated by the DNS dispatcher was dereferenced
twice - once in registered DNS handler, second time in the dispatcher
itself.
Since the buffer was allocated by the dispatcher, and it's not really
guaranteed that the buffer will be freed in the registered handler (this
depends on the processing outcome, the function may return early w/o
freeing the net buf in case of errors), it makes most sense for the
dispatcher to keep ownership of the buffer. Hence, the registered
handlers will no longer release the buffer provided in any case, and the
dispatcher will free it on exit.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Some of the new max32 family boards were missing the vendor name in
their board yamls and not being tested by `twister --vendor adi`.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Let's provisionally disable the nrf54l15 BT tests in CI
due to instability issues in the controller for this
platform.
See https://github.com/zephyrproject-rtos/zephyr/issues/74635
This should be reverted once the underlaying issue is fixed.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Remove obsolete workaround with conditional turning off "-g"
flag when Thread Local Storage used.
Recent versions of MetaWare have no issue with linking files with
TSL-related data.
Moreover, pointed workaround breaks userspace for recently added
ARC-V platforms, as they use both TLS and DWARF info while compilation
process.
Fixes https://github.com/zephyrproject-rtos/zephyr/issues/29920
Signed-off-by: Nikolay Agishev <agishev@synopsys.com>
Most people would expect green_pwm_1 to go to LD1 on the dev board.
However it is routed to CN1 pin 2, since routing it to LD1 would
interfere with SPI SCK on the Arduino connector. This PR adds a
comment to tell users that LD1 won't light up as expected and to
fix the comments stating which PWM goes to which pin.
Also updated the documentation to note this.
Signed-off-by: Glenn Andrews <glenn.andrews.42@gmail.com>
Apply the workaround for the issue "BBRAM First Byte" in the
NPCX49nF_Errata. This bypass limits the access to the BBRAMs' first byte
(i.e., the offset 0). As a result, only 127 bytes are available in npcx4
chips.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Bits in the BBRAM status register (BKUP_STS) are write-1-to-clear bits.
The current driver writes 0 to clear those bits, which is incorrect.
Fix it in this commit.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
These 2 tests have been seen failing in CI due to
the real time timeout.
Let's increase their deadline so it does not happen.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The generic stack pointer checker in the architecture code is
enough so we can remove the platform specific one. Besides,
xtensa_dc233c_stack_ptr_is_sane() does not do much checking
either.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This checks for stack boundaries during backtrace to make sure
we are not stepping into invalid memory.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Check that the stack frame pointer is valid before dumping
any registers while handling exceptions. If the pointer is
invalid, anything it points to will probably be also be
invalid. Accessing them may result in another access
violation.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
It is observed that during logging in fatal exception,
it prints "FATAL EXCEPTION(null)". Exact reason is unknown
as debugging through GDB would make it all work again. So
separating it into two log statements to avoid this situation.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Input subystem tests and samples were failing to build on these max32
boards because the zephyr,code property was missing on gpio-keys child
nodes. The devicetree binding doesn't specify the property as required,
but the driver implements a build assert when the property isn't
defined.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
With the update of the Kconfig symbols to new naming scheme,
CONFIG_PTHREAD does not exist anymore.
Use the new CONFIG_POSIX_THREADS instead
Follow-up: #73047
Signed-off-by: Pierrick Guillaume <pierguill@gmail.com>
In size_report script, if the DWARF section of ELF file contains both
debug_loc and a debug_loclists sections, LocationListsPair class is
used to track locations. In that case, parse_from_attribute was missing
one argument which was causing the script to fail.
Signed-off-by: Zhani Baramidze <jbaramidze@meta.com>
When TLS is used, `__tdata_start` is PROVIDED by
"thread-local-storage.ld" using absolute address, which
makes it land in wrong flash address. This causes risc-v startup
code to fail during memcpy/memset.
This PR overrides `__tdata_start` to use ADDR, which will
make sure it is placed in DROM region due to AT keyword.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
GitHub labels were hard to visually parse so use guilabel role to make them
stand out more, and put them in tabular format.
Other minor cosmetic tweaks
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Achieve proper syntax highlighting using "console"
language when command snippets start with a prompt.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
config file snippets should use "cfg" pygment to get proper highlighting
This commit updates all occurences where "kconfig" or other languages
were used.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add `FILE` typedef in the `stdio.h` so that when doing
`FILE *file` definition checkpatch doesn't complain about
the position of the '*' and fail in CI.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
According to the nrfx peripheral resource sharing example in
samples/boards/nrf/nrfx_prs it should be possible to share a resource
and apply the pins on peripheral that share resource ID.
However the sample only works since it only demonstrates UART and SPIM,
and by enabling both another SPIM driver, and UART is enabled for the
console. It would not be possible to enable a TWIM driver in addition.
Instead allow the PSELs if the configuration for NRFX has been enabled.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Currently iterable sections as per the documentation are added with
zephyr_linker_sources(SECTIONS ...) after bss/noinit.
This commit allows putting sections after common-rom.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Use PDU_BIS_LLID_FRAMED in empty PDUs for framed BIS
Allocate room for header when calculating max_pdu for framed BIS
Set group_sync_delay, stream_sync_delay and framed properly for BIS
broadcaster
Add missing call to isoal_tx_event_prepare() for BIS
Signed-off-by: Troels Nilsson <trnn@demant.com>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
- Assign sync_delay parameters for ISO-AL sink creation
- Store framing information from BIGinfo for use in sink creation
- Set max_octets for sink creation
Signed-off-by: Morten Priess <mtpr@oticon.com>
