Need to do the ENET module-level clock initialization from zephyr
instead of MCUX HAL, because now there are multiple zephyr drivers with
different init priorities that rely on the module being clocked. MDIO
must be initialized before the ENET MAC, and the MAC driver currently
calls ENET_Init from the HAL to initialize the clock, but MDIO needs the
module clock enabled first on some platforms. So replace the MAC init
with ENET_Up from the HAL, which doesn't include clock init, then do
clock init from a higher priority sys init based on the parent
compatible.
Also, add support for enet clock ungating with clock_control_on on ccm
driver do this with current platforms supported.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
- PHY can be set up as rmii but still use 25 MHz MDC, add DT property
value for this case
- Fix KSZ8081 driver spamming phy status in debug level logging,
and fix some other state/logging logic
- Fix PHY driver not rescheduling monitor work if first configuration
fails, change code path to use goto for errors
- Handle case where some phys are not using the gpio pins in phy driver
Make GPIO properties of ksz8081 phy optional since these hardware pins
may be unused on some boards
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This macros needed additional checks before invoking
arch_buffer_validate.
- size can not be less then 0. Some functions invoke this macro
using signed type which will be promote to unsigned when invoking
arch_buffer_validate. We need to do an early check.
- We need to check for possible overflow, since a malicious user
application could use a negative number that would be promoted
to a big value that would cause a integer overflow when adding it
to the buffer address, leading to invalid checks.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Commit adds implementation of the specification
recommendations regarding randomization of
responses on the access layer.
3.7.3.1 Transmitting an Access messages
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
At present, many of the NXP S32 shim drivers do not make use of
devicetree instance-based macros because the NXP S32 HAL relies on an
index-based approach, requiring knowledge of the peripheral instance
index during both compilation and runtime, and this index might not
align with the devicetree instance index.
The proposed solution in this patch eliminates this limitation by
determining the peripheral instance index during compilation
through macrobatics and defining the handler of SI Rx event within
the shim driver itself.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Remove the functions linux_socketcan_setsockopt() and
linux_socketcan_getsockopt() as they are unused.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The patch updates README with detailed description of the requirements
regarding target devicetree needed to correctly build the sample.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
When commit 5b4f4253c1 introduced
"nordic,qspi-nor" dts binding the sample wasn't aligned to the change.
From that moment the sample started to be filtered out by the Twister.
The patch adds Nordic's compatible to the test filter.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
This is continuation of the 64fbbd9a44
where spi-flash0 alias was defined for some of boards' devicetrees.
It's needed to turn on building samples/drivers/spi_flash for boards
with "nordic,qspi-nor" compatible.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
The 2 issues were found after CONFIG_OSDP_SC_ENABLED was enabled:
- missing curly brace after if
- typo in type name
Signed-off-by: Arkadiusz Wadowski <wadowski.arkadiusz@gmail.com>
During init i2c_ambiq device, the bitrate calculation is not correct,
results in incorrect device speed, or failed to configure i2c device
if clock-frequency is set to higher than I2C_BITRATE_STANDARD
Signed-off-by: Bryan Zhu <bzhu@ambiq.com>
Added possibility for link 2 modem mock instance for
validating P2P communication without any data stubbing.
Signed-off-by: Juha Heiskanen <juha.heiskanen@nordicsemi.no>
Added missing command and message handling for use existing
modem cmux for DCE role.
DCE CMUX connection can be now initialized from DTE side.
Signed-off-by: Juha Heiskanen <juha.heiskanen@nordicsemi.no>
Enable INPUT_SHELL and INPUT_KBD_MATRIX_STATE by default if the sample
is compiled with CONFIG_SHELL=y. This makes it easier to use the shell
commands in the sample by just enabling the shell and let any help
command turn on automatically.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a "input kbd_matrix_state" shell command. This prints the state of
a keyboard matrix in a much more compact representation than the normal
input event dump, but also keeps track of any key seen during the
execution and reports that on the "off" command. The output can be used
to help setting the actual-key-mask property.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Pulls update in nrfx_qspi driver with fixed order of applying workaround
for anomaly 215 on nRF52840 and anomaly 43 on nRF5340.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Add `BUILD_ASSERT`s to make sure that the interrupt bits
allocated to each levels are enough to cover the number of
IRQs in each respective level.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Updated the tests to use info from the devicetree or Kconfig as
ground truth and compare that with the output from the
functions under test.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Assert that the `local_irq` of each levels should only ranges
from `0` to `CONFIG_MAX_IRQ_PER_AGGREGATOR`, so that it doesn't
overflow the other aggregators.
Also, assert that the output of `z_get_sw_isr_table_idx` shouldn't
overflow the ISR table.
Update the `sw_isr_table` tests to test the range of
`CONFIG_MAX_IRQ_PER_AGGREGATOR` instead of the entire range of
level bits.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Split the `sw_isr_irq_parent_table` test into one that tests
the IRQ table index function which is generic and should
always be tested, and one that tests multi-instance -related
functions which only work in interrupt controller drivers that
has multi-instance implementation.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
The `CAT_3RD_LVL_LIST` macro is only used when
`CONFIG_3RD_LEVEL_INTERRUPTS` is enabled, so move it into the
compiler guard.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
The `irq` argument of the `Z_IF_DT_INTC_IRQN_EQ` macro
coincides with the `'irq'` argument passed into the `DT_IRQ`
macro, the former was supposed to be a number, while the latter
is a string/type, together this means that it was intepreted
as:
```c
DT_IRQ(node_id, <some_number>)
```
instead of
```c
DT_IRQ(node_id, irq)
```
as intended, so the macros never managed to match a device with
the IRQ properly, resulting in the `dev` member of the table
being NULL.
Solve this by renaming all the `irq` args in the macros to
`_irq` to avoid mixed usage.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Define the edge-trigger register base address based on whether
the PLIC node in the devicetree has an additional compatible
that supports edge-triggered interrupt.
Limited the implementation to Andes NCEPLIC100 only, updated
the devicetree binding of `andes_v5_ae350` accordingly.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
samples/boards/nrf/system_off does not enable CONFIG_PM so
it should not be listed as an example in system power management
documentation.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Update the readme to better describe contents of the sample, which is now
used to showcase the various input device types that LVGL offers.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Do not allow the modem to sleep if the driver is busy.
Fix CTS filtering. Ignore small pulses on the CTS line.
Fix socket restoration. Restored sockets could be mismatched
with a wrong type.
UDP sockets could be duplicated during restore.
Improve IO debug mode. Use warning message for IO debug mode
to easily see IO transitions color coded in a terminal.
Ensure the UART is enabled whenever the driver needs to send
commands to the modem.
Ensure DNS resolver is re-initialized after the modem is powered off.
PROD-307
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
SNTP response is not analyzed for uncertainty, and no uncertainty is given
to the `struct sntp_time` returned. Fix it with a Kconfig option that adds
optional SNTP uncertainty and timestamp fields in SNTP time struct, and
calculates these when parsing the response.
Adds two helper functions to convert Q16.16/Q32.32 in seconds to `int64_t`
in microseconds to facilitate this.
Also changes combined `lvm` field in `struct sntp_pkt` to bit-fields
`li`, `vn`, and `mode`.
Signed-off-by: Jasper Smit <git@jrhrsmit.nl>
This error message may confuse when `CONFIG_BT_MESH_ACCESS_LAYER_MSG` is
enabled and all messages are processed by the callback anyway.
This error message also confuses when a node is subscribed to the same
address as it publishes to, which makes it generating the error message
every time it publishes a message.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This change allows a custom RPL use pending mechanism and the mesh
settings work to store pending RPL entries. `bt_mesh_rpl_pending_store`
is a public API and should be implemented anyway. The custom RPL
implementation has to trigger settings with the
`BT_MESH_SETTINGS_RPL_PENDING` flag to ask the mesh settings work to
call `bt_mesh_rpl_pending_store`.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
