Use the already available in the tree mechanism of adding assembly
instructions right after WFI/WFE to implement the workaround for
nRF5340 anomaly 168 (replace the 4 NOP solution used on the network
core as it turned out to be insufficient) and provide two related
Kconfig options so that users are able to adjust the workaround to
their actual needs (disable it entirely or use it in the extended
version).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Configure to grant SI permissions to allow to set MAC,
update hash filter table and promiscuous multicast.
Fixes#66198
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
The PAN1783A evaluation board is a development tool for the nRF5340
from Nordic Semiconductor.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
Recent nRF 802.15.4 Radio Driver provides assert abstraction layer.
The assert abstraction layer is implemented in Zephyr in following
ways depending on the `NRF_802154_ASSERT_CHOICE` Kconfig choice.
`NRF_802154_ASSERT_ZEPHYR_MINIMAL` (default) gives ability to still
perform run-time checking of the nRF 802.15.4 Radio Driver operation
with minimum memory overhead and configurable behavior on fault
detection regardless of the `CONFIG_ASSERT` Kconfig option value.
`NRF_802154_ASSERT_ZEPHYR` gives ability to use asserts provided and
configurable by Zephyr including the ability to turn off the run-time
checking of the nRF 802.15.4 Radio Driver operation.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
This patch adds definitions for the nRF9151,
which is software-compatible with nRF9161.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Currently, the arch_curr_cpu() implementation always uses the TPIDRURO
register, even on Cortex-M CPUs where such a register is not available,
causing a CPU fault.
This commit fixes it by reverting to the use of generic kernel struct
to obtain the current cpu instead of using the TPIDRURO register.
Signed-off-by: Gustavo Romero <gustavo.romero@linaro.org>
Verify that TCP keep alive options can be set properly and that TCP
connections time out correctly when keep-alive probes fail to get
replies.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The number of Kconfig options for the TCP stack grew considerably,
therefore it makes sense to move them to a separate file not to bloat
the Kconfig file with generic networking options.
Take this opportunity to reorder TCP options, so that protocol
parameters (timings/buffer sizes) are not mixed up with optional
protocol features (fast retransmit/congestion avoidance etc.).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When a TCP connection is established, if there is no data exchange
between the two parties within the set time, the side that enables
TCP Keep-alive will send a TCP probe packet with the same sequence
number as the previous TCP packet. This TCP probe packet is an empty
ACK packet (the specification recommends that it should not contain
any data, but can also contain 1 nonsense byte, such as 0x00.). If
there is no response from the other side after several consecutive
probe packets are sent, it is determined that the tcp connection has
failed, and the connection is closed.
The keep-alive default parameters are aligned with Linux defaults.
Signed-off-by: Horse Ma <mawei@coltsmart.com>
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
- Allow non RTIO i2c drivers to be intermixed with RTIO drivers
- Remove reference to rtio_spsc_drop_all()
- Fix impllicit cast which throws an error with more restrictive
compile flags
Signed-off-by: Yuval Peress <peress@google.com>
Fix intel_adsp_generic.rst following the merge of the rimage git
repository back into the sof git repository:
- https://github.com/thesofproject/sof/issues/7270
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Ambiq UART requires specific busy wait during initialization for
propagating powering control registers, original k_busy_wait()
used here generated a dead loop because k_busy_wait() relays on
timer, who's driver is initialized after UART(UART init in
PRE_KERNEL_1, timer init in PRE_KERNEL_2), replace k_busy_wait()
with checking power status register is more suitable here.
Signed-off-by: Bryan Zhu <bzhu@ambiq.com>
The float_apis group is incorrectly placed in x86/32 header.
This should be in kernel.h enclosing k_float_* functions.
So move it.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The `mikroe_mini_m4_for_stm32` board doesn't have its RTC node
enabled, and is failing the following test:
`tests/benchmarks/footprints/benchmark.kernel.footprints.pm`
This board seems to have been missed out from 44b8370, let's
enable the rtc & clk_lsi here.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
This can be used to interpret the "status" in the disconnect result event.
To start with a few common reasons are enumerated but can be extended in
the future.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This can be used to interpret the "status" in the connect result event.
To start with a few common reasons are enumerated but can be extended in
the future.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
If observed resource was written during the pMin period, it did
not schedule any wake-up event into the future. Notify message would
then only be generated as a result of any other (like Update) event.
Refactor check_notifications() to follow same pattern as retransmit_req().
Return the next event timestamp, which could be now.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Automatic Wi-Fi station reconnection is forced even when
application requests disconnection. This PR adds a check
in the disconnection event reason to decide whether or not
perform the reconnection.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
With TF-M enabled the storage_partition can be used as memory that is
known to be configured as non-secure flash region.
The slot1_ns_partition partition is only correct when TF-M is built
with BL2 enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Make sure that the flash partition is valid.
With TF-M enabled the storage_partition can be used as memory that is
known to be configured as non-secure flash region.
The slot1_ns_partition partition is only correct when TF-M is built
with BL2 enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Print a finished message, so that it is clear that this in the end
of the sample. This makes it certain that we didn't crash without
output on the last test.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Stop erasing outside of the test partition.
We shouldn't really on this being accesible memory.
This region may be consider as secure when application is non-secure.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Enable the TF-M NS storage partition for nordic boards.
This partition is otherwise not used, and configured as secure.
Fixes: #59376
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add `compatible` node to Ambiq SoCs, along with secondary common compat,
since they share many similarities.
Signed-off-by: Mateusz Karlic <mkarlic@antmicro.com>
As the display API now check against valid callback functions and
returns -ENOSYS (or equalent), there is no need to provide
such functions in the driver code
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
The FTM counter modulo register (MOD) holds a 16-bit value, but PWM
set_cycles API allows to set 32-bit cycles values.
Fixes#66226
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The arm_core_tz.c trustzone driver was developed by Nordic and was
previously used by Nordic, but it is not used by us any more. Since we
stopped using it I can see that it has bit rotted (the include path
for tz.h is not available), so no else has started using it either
evidently.
Remove the broken and dead code.
We keep the HAS_ARM_SAU Kconfig as it is selected by a myriad of
platforms and determines if __SAUREGION_PRESENT is defined. I have
been unable to prove that this define is also unused.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This fixes missing connection reference release.
The bt_conn_le_create returns the connection object reference that needs
to be released by API caller.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
The bt connect and bt connect-name commands should only
attempt to connect to connectable devices that we are not
already connected to.
This commit moves the check for BT_GAP_ADV_PROP_CONNECTABLE
as well as checks that we do not already have a connection
to that device with the current ID.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The is_substring did not work for true substrings, as it
would always compare [0] to [0], so it would return false
for the substring "BC" being in "ABC".
Removed the tolower as it is not necessary and fixes the issue.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Fix error writing to the CR register on the first call to SPI configure on
NXP MKE1xF. On the first call, the module clock is not enabled and writing
to the CR register will fail.
Fixes: #66036
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The DMA channel data structure can retain config information.
We need to clear this everytime dma_configure is called on a
channel.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Use helper function to convert string to int for appearance value.
This makes the code more clear, as the big-endian conversion function
gives the wrong impression about the byte order of advertising data.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
It's not good to see struct_tags.json change from one build to the next
when nothing changes.
Python's sets are not deterministic, see long story for older commit
f896fc2306 ("scripts: gen_handles: Sort the device handles")
Simply convert multiple_directories to a sorted list before using it.
Fixes commit 80e78208e6 ("kernel: syscalls: no need to include all
syscalls in binary")
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
