Use the sys_cache* functions to enable the caches on same70 and
samv71. This will ensure that CONFIG_CACHE_MANAGEMENT is
considered correctly.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Use sys_cache_data_enable instead of arch_dcache_enable to enable
the cache. This will ensure that CONFIG_CACHE_MANAGEMENT
is considered correctly.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Remove the redundant cache config options for kv5x and use
the sys_cache* functions to enable the caches. This will automatically
consider CONFIG_CACHE_MANAGEMENT.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Replace the redundant cache config options for the nxp_imx and
use sys_cache* functions to enable the caches. These will automatically
consider CONFIG_CACHE_MANAGEMENT.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Use sys_cache* for enabling the caches in nxp_s32. This automatically
considers CONFIG_CACHE_MANAGEMENT and will activate the
cases only if this is active.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Some charger devices (such as BQ25710 and ISL9241) issue
notifications to the system via a dedicated line (such as
the PROCHOT signal on x86 platforms) to almost instantly
throttle the system load to prevent a brownout event.
This patch introduces two properties to configure two
distinct input current notification events of different
severity.
Signed-off-by: Ricardo Rivera-Matos <ricardo.rivera-matos@cirrus.com>
Adds support for setting a falling input voltage limit regulated
by an analog loop. Under heavy loads the analog loop will throttle
the charge current to prevent the power source from crashing.
Signed-off-by: Ricardo Rivera-Matos <ricardo.rivera-matos@cirrus.com>
Adds support for setting the target threshold for an input current
limit regulated by an analog loop. The analog loop responds by
throttling the charge current limit as necessary.
These are distinct from comparator based overcurrent protection
thresholds that isolated the charger from the power source when
triggered.
Signed-off-by: Ricardo Rivera-Matos <ricardo.rivera-matos@cirrus.com>
Previously, if an SD I/O operation was attempted while another thread
held the mutex for the SD card, the I/O operation would simply fail. Add
a timeout to k_mutex_lock calls within the SD subsystem, so that
multithreaded access to the SD card instead blocks until the SD card is
available for I/O
Fixes#66211
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Switch to using named IRQs as index-based access makes no guarantees about
devicetree interrupt order.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch to using named IRQs as index-based access makes no guarantees about
devicetree interrupt order.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Consistently use "int0" and "int1" as interrupt names for CAN controllers
based on the Bosch M_CAN IP core. This aligns with the upstream Linux
bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit partially reverts a change which was introduced in the
previous commit 5b9a0e5456.
usb_dc_ep_start_read() should also be called on transfer endpoints
like it has been before, otherwise the endpoint will not be armed
after it has been reconfigured.
Signed-off-by: Manuel Aebischer <manuel.aebischer@netmodule.com>
Needed for full functionality of the job server in twister
which only works with kitware supplied ninja version.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support for J-Link over IP and J-Link remote server.
If the "--dev-id" is a valid ip, the transport over ip is selected.
Otherwise usb is selected.
Signed-off-by: Michael Arnold <marnold@baumer.com>
Added the sl_assert, sl_common, em_core_generic, em_system_generic files
and updated related files in gecko/common and gecko/emlib to include
the mentioned files.
Signed-off-by: Sateesh Kotapati <sateesh.kotapati@silabs.com>
This is a follow-up to commit c7e4d23c5d.
After all calls to `nrfx_dppi_*` and `nrfx_ppi_*` functions were
replaced with corresponding `nrfx_gppi_*` calls, it is no longer
needed to include the `nrfx_dppi.h` and `nrfx_ppi.h` headers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The sample needs to check in Kconfig whether PPI or DPPI is present
on the target platform in order to enable the proper allocator in nrfx.
It should not use the `HAS_HW_NRF_*` symbols for this as those take
into account also the status of the corresponding DT node, not only
its presence.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This sample makes calls to the nrfx_gpiote driver functions that
require absolute pin numbers, not relative to a given GPIO port,
so instead of getting the numbers with the `DT_GPIO_PIN` macro,
it should use `NRF_DT_GPIOS_TO_PSEL`.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... so that it is possible to use a GPIO expander pin as the CS line.
Communication with the expander may involve an operation that cannot
be done from the interrupt context (e.g. an I2C transaction).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit ea1be7f242.
After the driver performs its initialization, it needs to deactivate
the QSPI peripheral. Otherwise, the peripheral would unnecessarily
consume power until some QSPI operation is performed (and only then
it will get deactivated), what depending on the application may take
a significant amount of time.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
`release` is a mandatory method in the `struct spi_driver_api` API but
is not implemented in the SPI emulator. This can cause a test calling
`spi_release()` to segfault. Add a stub implementation that just returns
zero.
Signed-off-by: Tristan Honscheid <honscheid@google.com>
With commit 734adf52c6, the MCUX LPI2C config structure no longer
contains a direct base address pointer. The base address must be
accessed via DEVICE_MMIO_NAMED_GET. Some declarations in the LPCI2C
target mode handler still used the old method of accessing the base
address, causing a build failure. Fix these accesses to use the local
declaration of the "base" variable.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
clangsa reports the error
mdio_nxp_enet.c:245:10: error: label at end of compound statement:
expected statement
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Current setting missed some necessary files which should be
covered by Ambiq platforms. Add them in this commit.
Signed-off-by: Aaron Ye <aye@ambiq.com>
Convert the sample for the lmp90100_evb shield to use devicetree for
configuring the ADC channel.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Include zephyr/dt-bindings/adc/adc.h and zephyr/dt-bindings/gpio/gpio.h in
the shield DTS overlays to simplify using this shield in application
overlays.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Mention the change in the ti,lmp90xxx bindings to use the common
io-channel-cells name "input" instead of "positive" and "negative".
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use the common io-channel-cells name "input" instead of "positive" and
"negative" to make this binding work with the various ADC DT macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add a small paragraph about the input SDL touch driver,
clarifying the evdev driver is not the only input one.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add a small paragraph about the EEPROM simulator,
and improve slightly the flash simulator section
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Changes shield processing order from being on a root-by-root
basis to being order they were supplied to cmake
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
If accept() returns an error, it typically means that the
system is running out of resources. In this case sleep
some time in order the system to cool down a bit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If accept() returns an error, it typically means that the
system is running out of resources. In this case sleep
some time in order the system to cool down a bit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Make the retransmission timer much shorter so that the test
is run faster (about 50% faster test run in qemu_x86).
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add a function callback that is called when the TCP connection
is closed. This is only available if doing network tests.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Make sure the connection is closed by the timer if the final
ack is lost in closing state.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
