Cnfigures the LPC55xxx SoC with dual-core (first core boots the second)
and enables the on-SoC mailbox to handle inter-core communication.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Added gpio_loopback to indicate that test requires pins to be
shorten. This allows to filter out tests on setup which does
not have pin setup.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Currently a lot of common kconfig options are being set in
board-specific overlays.
This commit puts them in the main prj.conf.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
The STM32F105xx USB clock goes through a prescaler either PLL1 x2 /2
or PLL1 x2 /3, the output of this must be 48 MHz. As such, the output
of PLL1 must be 48 MHz or 72 MHz.
NOTE: This requires that the system is running from PLL1 (PLLCLK).
Support for running from PLL2 will be implemented in the future.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
The STM32F105xx is effectively an STM32F107xx without Ethernet. As such,
it's possible to include the STM32F105's device tree from STM32F107, and
add in any additional nodes (currently just DMA2, though according to
the datasheet, this may be supported by the STM32F105xx and other parts
too).
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
Set the prescaler in register BTR according to the configured bitrate in DTS.
This bug appeared in commit 8b6c1bd4b7
Signed-off-by: Julien D'Ascenzio <julien.dascenzio@paratronic.fr>
```
/home/humanentity/zephyr/drivers/ipm/ipm_handlers.c:23: undefined reference to 'z_impl_max_data_size_get'
```
The error shows when having CONFIG_BT=y and CONFIG_USERSPACE=y, and
is easily reproduced by adding
```C
CONFIG_USERSPACE=y
```
to `samples/bluetooth/peripheral/prj.conf` and building the sample.
E.g.
```
$ west build -p auto -b nrf5340pdk_nrf5340_cpuapp samples/bluetooth/peripheral
```
Signed-off-by: Peter Andersson <pelleplutt1976@gmail.com>
Retain the assumption that the loop will assign a pointer, but
initialize it pointer first to eliminate build warnings.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The fs_seek and fs_tell are expected to return -ENOTUSP if file system
driver lacks implementation of said funcions.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Remove all odr values from Kconfig and always init it
at 12.5Hz. It is responsibility of application to set
the rate to a different value using SENSOR_ATTR_SAMPLING_FREQUENCY.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common binding file that will be included by all bindings
handled by iis2dlpc driver. For now this includes optional drdy-gpios
property and it is shared by the i2c and spi version of the driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The LwM2M firmware pull object no longer uses the system workqueue
to execute firmware_transfer(), but directly executes it itself.
Previously, the workqueue would be blocked because firmware_transfer()
indirectly calls a blocking connect(). This would lead to problems
with e.g. modem drivers that use UART to interface with the modem
hardware, as some UART drivers use the workqueue.
Fixes#31053.
Signed-off-by: Maik Vermeulen <maik.vermeulen@innotractor.com>
As the tcp header struct can be cast to unaligned memory, mark
it as packed and access fields using UNALIGNED_GET/PUT when
needed.
Fixes#31145
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The interrupt numbers for two socs for the gpio peripheral was wrong.
This commits corrects this issue for the relevant socs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
The watchdog and rng nodes were a sub-node of the gpio node.
This commits corrects this issue for the relevant socs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds support for ADC on G0 series.
Simple implementation: sequencer not fully configurable,
and only one common sampling time.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
PWM, as other peripherals should not be enabled as part of
default board configuration.
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There are some drivers in the tree that support devices on multiple
different buses, although so far this has not been represented in
device tree using the bus concept. In order to convert these drivers &
bindings to refer to a formal bus in device tree we need to be able to
match bindings which lack an explicit "on-bus: ..." value against any
parent bus. This will also be needed for any external bindings, since
those would not be aware of on-bus (as it's a Zephyhr-specific
extension).
The two drivers I'm particularly targeting is the ns16550 UART driver
(drivers/serial/uart_ns16550.c) and the DW I2C driver
(drivers/i2c/i2c_dw.c). They both support devices with a fixed MMIO
address as well as devices connected and discovered over PCIe. The
only issue is that instead of encoding the bus information the proper
DT way these bindings use a special "pcie" property in the DT node
entries to indicate whether the node is on the PCIe bus or not.
Being able to convert the above two drivers to use the DT bus concept
allow the removal of "hacks" like this:
if DT_INST_PROP(0, pcie) || \
DT_INST_PROP(1, pcie) || \
DT_INST_PROP(2, pcie) || \
DT_INST_PROP(3, pcie)
to the more intuitive:
if DT_ANY_INST_ON_BUS_STATUS_OKAY(pcie)
This also has the benefit that the driver doesn't need to make any
arbitrary assumptions of how many matching devices there may be but
works for any number of matches. This is already a problem now since
e.g. the ns16550 driver assumes a maximum of 4 nodes, whereas
dts/x86/elkhart_lake.dtsi defines up to 9 different ns16550 nodes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Get rid of weak functions adding a new API to register an object to
receive notifications when the system changes power state.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Rename Kconfig BT_CTLR_SCAN_SYNC_ISO_MAX to
BT_CTLR_SCAN_SYNC_ISO_SET, to be consistent with other
Kconfig naming.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
AUX_CONNECT_RSP PDU static buffer definition was missing one
byte required for the Extended Header Flags.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Document with comments, the explanation of node rx count and
the design of the free rx PDU management.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
