Add build tests for the IT8801 MFD drivers, including GPIO,
Input and PWM functionalities.
GPIO, Input test: west build -p always -b native_sim
PWM test: west build -p always -b it82xx2_evb
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Separate the current driver for the FPGA iCE40 into two different ones.
One implements only the SPI load mode, the other one only the GPIO
bitbang mode.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Don't duplicate the test's output running it on `native_sim` after
`LOG_BACKEND_NATIVE_POSIX` was enabled by default (bd9836be8c)
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Use a string for the mipi-mode property over an integer value, as this
significantly improves the readability of the MIPI DBI device binding.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Replace NULL checks for the set and clear registers with BUILD_ASSERTs
in the iCE40 device instantiation.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Some nodelabels in the display build_all test overlay lacked a "test"
prefix, causing test failures on boards that also define displays with
this nodelabel. Prefix these nodes with "test" to resolve this issue.
Fixes#81610
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a driver for the MB85RSM1T FRAM chip.
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Replace the enum for load modes for the iCE40 with a boolean flag,
as there are only two options:
- SPI: default, which should be used whenever possible
- GPIO bitbang: workarorund, in case a low-end microcontroller is used
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Renamed the label of 'ti_tmp116_eeprom@0' node because 'eeprom' label name
already exists in some boards, such as adp_xc7k/ae350, bytesensi_l,
same54_xpro.
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
Remove CONFIG_MMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the mmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
mmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The peer remote device "source_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Instead of fixing csi2rx clock frequencies, set them according to the
pixel rate got from the camera sensor.
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The peer remote device "sensor_dev" can be retrieved from the
remote-endpoint-label. Direct reference via phandle is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The ILPS22QS is an ultra-compact piezoresistive absolute pressure sensor
which functions as a digital output barometer, supporting dual full-scale
up to user- selectable 4060 hPa. The device delivers ultra-low pressure
noise with very low power consumption and operates over an extended
temperature range from -40 °C to +105 °C.
(https://www.st.com/en/mems-and-sensors/ilps22qs.html)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add wsen_hids_2525020210002 driver with
the corrected name and compatibility with
the hal update as well as added new features.
Signed-off-by: Wajdi ELMuhtadi <wajdi.elmuhtadi@we-online.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Some devices may belong to >1 power domain, so with the current design
this is something not possible to describe. It's worth to note that
Linux also uses the `power-domains` naming scheme, not `power-domain`.
This patch also introduces `power-domain-names` so that each entry in
`power-domains` can be given a name if needed. `#power-domain-cells`
is now required as well.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Use EXTRA_CONF_FILE in sample yaml files,
that replaced deprecated OVERLAY_CONFIG
since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Adds a Kconfig fragment which changes the MFD init priority
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
The test targets the following devices at this time.
- atmel,winc1500
- inventek,eswifi
- inventek,eswifi-uart
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Replace wrong compatibility strings for max14906 and max14916.
Fix wrong addressees for max14906 and max14916.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
Fixed incorrect I2C register definitions in the test file
tests/drivers/build_all/sensor/i2c.dtsi.
Signed-off-by: Paweł Czaplewski <pawel.czaplewski@arrow.com>
TI tmp1075 driver implemented based on tmp108 driver.
The driver initializes the sensor based on the DTS.
Added tmp1075 example overlay file to thermometer sample.
All you need to do to use the sensor is to connect the I2C and
optionally interrupt line.
To see default DTS configuration option inspect `ti,tmp1075.yaml`
bindings file and sensor spec.
Signed-off-by: Paweł Czaplewski <pawel.czaplewski@arrow.com>
Change the unit of the sense resistor in the devicetree binding from
micro-ohms to milli-ohms. This is done for three reasons.
Firstly, the maximum value resistor that can currently be represented
is 4.2 kOhms, due to the limitation of devicetree properties to 32 bits.
Secondly, storing the resistance at such a high resolution makes
overflows much more likely when the desired output unit is micro-amps,
not milli-amps.
Finally, micro-ohms, are an unnecessarily precise unit for the purpose
of these calculations, and a resolution that is not realistic to
achieve. The high resistor resolution results in large divisors that
reduce the resolution of outputs. Unlike resistors characterised down to
the micro-ohm, devices wanting to measure micro-amps are actually
realistic.
Signed-off-by: Jordan Yates <jordan@embeint.com>
